Koshin PX-55011A Bedienungsanleitung

Original instructions

Engine Pump

Moto-pompe

motorpumpe

Motopompa

Bomba del Motor

Model

Modèle

Modell

Modello

Modelo

« PX-55011 / 55022 / 55022A »

« PXL-52511 / 52522 »

INSTRUCTION MANUAL

MANUEL D’UTILISATION

BEDIENUNGSANLEITUNG

MANUALE D’USO

MANUAL DE INSTRUCCIONES

12 Kami-Hachinotsubo Kotari, Nagaokakyo City, Kyoto 617-8511 JAPAN

TEL.+81-75-954-6111 FAX.+81-75-954-6119

www.koshinpump.com

- 1 -

PLEASE READ THIS MANUAL BEFORE OPERATION.

"ACCEPTABLE FOR INDOOR OR OUTDOOR USE"

"SUBMERSIBLE PUMP"

CAUTION

Before use, please make sure to read the instruction manual.

Do not operate the pump out of water or insufﬁcient water.

WARNING

Risk of electric shock. This pump is supplied with a grounding conductor and

grounding-type attachment plug. To reduce risk of electrical shock, connect only to a

properly grounded, grounding-type receptacle.

TO REDUCE THE RISK OF ELECTRIC SHOCK, INSTALL ONLY ON A CIRCUIT

PROTECTED BY A GROUND-FAULT CIRCUIT-INTERRUPTER (GFCI).

NOTE

This pump has not been investigated for use in swimming pool or marine areas.

This pump has been evaluated for use with water only.

High Performance Submersible Pump

OPERATION MANUAL

• Thank you for choosing Koshin Submersible Pump.

• This manual is prepared for your safety when operating pump.

Please read carefully and comprehend fully before use.

(Wrong usage could cause injury or death.)

• Please keep this manual handy for future reference.

- 2 -

EN AFTER USING PUMP

1. In cold climates, do not allow pump to freeze.

Remove pump from water to prevent damage due to freezing.

2. Completely drain and dry pump of water before storing.

CAUTION

The pump is used a double mechanical seal.

(See ﬁgure)

Consulting the following table assemble it.

Mechanical

seal

Motor side

(Carbon)

Pump side

(Carborundum)

Outside

diameter 20.5mm 20.0mm

Internal

diameter 16.0mm 15.5mm

Double mechanical

Internal diameter

Motor

side Pump

side

Outside diameter Carborundum

Carbon

TROUBLESHOOTING GUIDE

PROBLEM POSSIBLE CAUSE SOLUTION

No start at

all or stops

immediately

after start

Not properly connected to

power circuit Correct the connection

The GFCI, leakage circuit

breaker is actuated Check the power circuit

The impeller is caught

by foreign substance Repair the point of leakage

ecalperroriapeRtnrubsirotoM

gnitarehtotegatlovehtesiaRpordegatloV

Failure during

operation The protector is actuated

Remove foreign substance if

the impeller is clogged

Lower the liquid temperature

if it is too high

No pumping

or poor

performance

gnitarehtotegatlovehtesiaRpordegatloV

High delivery head Lower the head

Discharge pipe is clogged Overhauling

tnemecalpeRraewrellepmI

Clogging of foreign matter

in strainer pump Overhauling

- 3 -

INSTALLATION AND USE

• An acceptable motor-control switch shall be provided at the time of installation.

• Thermally protected

1. This pump works under an automatic surface control

system whereby it is automatically switched on and off by

a ﬂoat switch.

2. The pump starts automatically when the water level rises

and the ﬂoat comes up to the ON water level, and stops

automatically when the water level falls and the ﬂoat

comes down to the OFF water level.

3. The ON and OFF water levels can be adjusted by

loosening the cord band bolt. However, the length of the

cord between the cord band and the ﬂoat switch should

be between 50mm and 150mm, otherwise the ﬂoat switch

will not operate normally.

4. The ﬂoat switch should be installed where it does not

come into contact with walls or is any other obstructions.

5. The pump should not be installed where water is

discharged directly onto the ﬂoat.

AFTER USING PUMP

1. In cold climates, do not allow pump to freeze.

Remove pump from water to prevent damage due to freezing.

2. Completely drain and dry pump of water before storing.

CAUTION

1. Leak Current Breaker

For home use, attach a leak current breaker, GFCI (offered separately) to ensure safety.

2. Connect the power source

Absolutely refrain from connecting this pump to any other power source than 110V

AC or 220V AC, 50Hz.

3. Water to use

Absolutely refrain from using the pump for any oil, sea water, strong alkaline or strong

acidic solution, or any agricultural chemicals.

4. Do not run dry!

Idling can cause trouble, to prevent short cycling place pump at deepest position as possible.

5. Handling of power cord (cabtype cable)

Never lift or move pump by power cord. Only lift by handle or tie rope supplied to handle.

b. Select and use proper size extension cord. Do not run extension cord in water.

6. Using in bath, etc.

Do not enter the water when pump is being used.

The OFF water level

: 100~130mm

Cord Band

50~150mm

Float switch

The ON

water level

350~

410mm

Leave

space

- 4 -

EN MAINTENANCE AND INSPECTION

1. Periodically check the insulated condition with a megger tester.

To be acceptable, the resistance between the earthing wire and the power cord should

be 100Meg ohm and higher.

2. The shaft of the water-tight mechanism as the most critical part of the pump is sealed

with liquid parafﬁn. The life changes greatly depending on the operating condition but

the quantity should be checked periodically.

Use 230cc of Crystol No.70 by Exxon Mobil Corporation for the sealing. The liquid

parafﬁn can be checked easily by removing the hexagon socket head bolt at a lower

side of the pump body.

SPECIFICATIONS

MODEL PX-55011 PX-55022 PX-55022A PXL-52511 PXL-52522

PUMP

Connection Dia

50 mm (2") 25 mm (1")

Total Head 10 m (32.8 ft)

Delivery Volume

260 L/min

(68.6 USG/min) 120 L/min

(31.7 USG/min)

MOTOR

Voltage AC-110V AC-220V AC-110V AC-220V

Frequency 50 Hz

Rated Current 6.5 A 3.2 A 6.0 A 2.9 A

Out put 400 W

Consumption 580 W 620 W 590 W 540 W

Revolution 2900 rpm

Model Induction Motor

Power Cord

10 m (32.8 ft)

[BAB-1]

5 m (19.6 ft)

[BAA-1]

10 m (32.8 ft)

[BAB-1/BAC-1]

5 m (19.6 ft)

[BAA-1]

10 m with

Float Switch

(32.8 ft)

[BAA-0]

10 m (32.8 ft)

Standard

Accessories 1 Rope (5 m) , 1 Hose Band,

1 Hose Nipple

1 Rope (5 m) , 1 Hose Band

1 Cupling Packing

1 Cupling , 1 Hose Nipple

Net Weight 11 kg (24.2 lb)

11.8 kg (26 lb)

12.7 kg (28 lb)

*Starting current is three times higher than rated current.

- 5 -

PERFORMANCE CURVE

20 40 60 80

1000 200 300

PX - 55011

- 55022

- 55022A

PX -55011

-55022

-55022A

DELIVERY VOLUME (L/min)

*Performance ratings are guaranteed minimum, not inﬂated maximum.

**Starting current is three times higher than rated current.

(USG/min)

TOTAL HEAD (m)

(ft)

DEMENSION

390㨪490

180

243

50㨪150

160

5000

The on water level

350㨪410

10000

222.5

151.5 PX-55022A

ONLY

The off

water level

100㨪130

330

308

279

208

Ǿ72

PLUG

MODEL

PX-55022-BAA

PX-55011-BAB

PX-55022-BAB

PX-55022-BAC

PX-55022A-BAA

- 6 -

EN PARTS LIST

PX-55011-BAB / PX-55022-BAA/BAB/BAC / PX-55022A-BAA

No.

PARTS CODE

PARTS NAME

QTY

0438123 PX-5011 MOTOR ASSY 110V 1

0438120 PX-5022 MOTOR ASSY 220V 1

0438151 PX-5022 CE MOTOR ASSY 220V 1

2A 0430289 POWER CORD ASSY 5m 1

2B 0438102 CE POWER CORD ASSY 10m 1

2C 0438142 EU POWER CORD ASSY 10m 1

3 0390031 CORD SUPPORTER 1

4 0260018 CORD BAND 1

5 0438066 CHAIN ASSY 1

6 703305100 SCREW M5×10 2

7 827305005 HEXAGON NUT M5 1

8 0438155 FLOAT ASSY 1

9A 703305104 SCREW M5×14 2

9B 703305110 SCREW(55022A) M5×50 2

10 0390330 SUPPORT PLATE 1

11 707805046 SCREW M5×12 1

12 0430284 HEAD PACKING 1

13A 743605031 HEXAGON BOLT M6×18 4

743605031 HEXAGON BOLT(55022A) M6×18 3

13B 743605032 HEXAGON BOLT(55022A) M6×20 1

14 0430441 IMPELLER FIXING BUSH 1

15 0430285 IMPELLER 1

16 0430273 BACK LINER 1

17 0430271 FRONT COVER 1

18 889955125 O-RING G125 1

19 734505037 HEXAGON SOCKET BOLT M5×20 3

20 0390003 MECHANICAL SEAL 1

21 0340142 SEAL RING 1

22 0340153 BIND SCREW M6×8 1

No.

PARTS CODE

PARTS NAME

QTY

23 0430300 IMPELLER WASHER 1

24 0390025 IMPELLER ADJUSTING WASHER 2

25 0390037 SOCKET BOLT M10×12 1

26 854255010 SEAL WASHER φ10 1

27 0430274 CASING 1

28 0430269 SUCTION 1

29 0430270 STRAINER 1

30 0430305 DELIVERY FLANGE G2 1

31 0430283 DELIVERY PACKING 1

32 846005008 WASHER φ85

33 835305008 HEXAGON CAP NUT M8 3

34 0390213 HOSE NIPPLE φ50 1

35 940019060 HOSE BAND φ60 1

36 0398020 PS ROPE 5M 1

37 735705162 HEXAGON BOLT M8×70 3

38 895154014 OIL SEAL VR14A 1

39 0430301 THRUST WASHER 1

40 0430299 THRUST PACKING 1

41 845305008 TOOTHED WASHER 8B 1

42 846505008 WASHER φ8-1.6 1

43 0430268 HANDLE 1

44 0430392

110V CONDENSER(55011) 32µF 260VAC

0430393

220V CONDENSER(55022) 8µF 480VAC

0430344 PX-55011-BAB NAME PLATE 1

0430317 PX-55022-BAA NAME PLATE 1

0430336 PX-55022-BAB NAME PLATE 1

0430479 PX-55022-BAC NAME PLATE 1

0430558 PX-55022A-BAA NAME PLATE 1

46 0390383 PARAFFIN OIL 230CC 1

- 7 -

PERFORMANCE CURVE

20 3010 40 50

100 150

020050

PXL -52511

-52522

DELIVERY VOLUME (L/min)

*Performance ratings are guaranteed minimum, not inﬂated maximum.

**Starting current is three times higher than rated current.

(USG/min)

TOTAL HEAD (m)

(ft)

DEMENSION

224

Ǿ191

152

315

286

215

10000

(For BAB)

10000(For BAC)

- 8 -

EN PARTS LIST

PXL-52511/ PXL-52522

No.

PARTS CODE

PARTS NAME

QTY

10438123 PX-5011 MOTOR ASSY 110V 1

0438151 PX-5022 CE MOTOR ASSY 220V 1

2A 0438102 CE POWER CORD ASSY 1

2B 0438142 EU POWER CORD ASSY 1

3 0390031 CORD SUPPORTER 1

4 0260018 CORD BAND 1

5 0438066 CHAIN ASSY 1

6 703305100 SCREW M5×10 2

7 827305005 HEXAGON NUT M5 1

8 703305102 SCREW M5×14 2

9 743605031 HEXAGON BOLT M6×18 4

10 0430441 IMPELLER FIXING BUSH 1

11 0430285 IMPELLER 1

12 0430271 FRONT COVER 1

13 889955125 O-RING G125 1

14 734505037 SOCKET BOLT M5×20 3

15 0390003 MECHANICAL SEAL 1

16 0390383 PARAFFIN OIL 230CC 1

17 0430300 IMPELLER WASHER 1

18 0390025 IMPELLER ADJUSTING WASHER 2

19 0390037 SOCKET BOLT M10×12 1

20 854255010 SEAL WASHER φ10 1

21 0430334 PX-L CASING 1

22 0430329 PX-L SUCTION 1

23 0430241 PX-L STRAINER 1

24 0430350 DELIVERY FLANGE 1

25 0430242 STUD BOLT 3

26 0430236 STRAINER STAND 1

27 0430239 SEAL RING 1

No.

PARTS CODE

PARTS NAME

QTY

28 0430331 ONE WAY CHECK VALVE 1

29 827405008 HEXAGON NUT M8 3

30 0430283 DELIVERY PACKING 1

31 0430290 STUD BOLT M8×36×11/21 2

32 846005008 WASHER φ82

33 835305008 HEXAGON CAP NUT M8 3

34 0340781 COUPLING 1

35 0340782 HOSE NIPPLE 1

36 0340065 COUPLING PACKING 1

37 940019032 HOSE BAND φ32 1

38 0398020 PS ROPE 5m 1

39 0340142 SEAL RING 1

40 0340153 BIND SCREW M6×8 1

41 0430301 THRUST WASHER 1

42 895154014 OIL SEAL VR14A 1

43 0430299 THRUST PACKING 1

44 845305008 TOOTHED WASHER 8B 1

45 846505008 WASHER φ8-1.6 1

46 854255008 SEAL WASHER φ83

47 0430361 PX-L LONG PIPE 2

48 0430362 PX-L SHORT PIPE 1

49 0430360 PX-L SUCTION PACKING 1

50 0430268 HANDLE 1

51 0430393 220V CONDENSER 8µF480VAC 1

52 0430284 HEAD PACKING 1

0430379 PXL-52511-BAB NAME PLATE 1

0430380 PXL-52522-BAB NAME PLATE 1

0430577 PXL-52522-BAC NAME PLATE 1

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Sprachen:

Andere Koshin Wasserpumpe Handbücher

Koshin

Koshin MF-2524 Bedienungsanleitung

Koshin

Koshin KTH-S Series Gebrauchsanweisung

Koshin

Koshin HIDELS Bedienungsanleitung

Koshin

Koshin FD-12 Bedienungsanleitung

Koshin

Koshin FR-200 Bedienungsanleitung

Koshin

Koshin PKG-1500 Bedienungsanleitung

Koshin

Koshin SEV-25S Bedienungsanleitung

Koshin

Koshin FP-25 Bedienungsanleitung

Koshin

Koshin FS-12D Bedienungsanleitung

Koshin

Koshin Agro-Mate PGH-50 Bedienungsanleitung

Koshin

Koshin PONSTAR PX Series Bedienungsanleitung

Koshin

Koshin KTH - 100X Bedienungsanleitung

Koshin

Koshin SEY-50D Bedienungsanleitung

Koshin

Koshin GB-13T Bedienungsanleitung

Koshin

Koshin PBX Series Bedienungsanleitung

Koshin

Koshin PONSTAR PB Series Bedienungsanleitung

Koshin

Koshin SEH-50X Bedienungsanleitung

Koshin

Koshin PXJ-250 Bedienungsanleitung

Koshin

Koshin SEV-25L Bedienungsanleitung

Koshin

Koshin SEH-50X Bedienungsanleitung

Koshin

Koshin SEV-50D Bedienungsanleitung

Beliebte Wasserpumpe Handbücher anderer Marken

Neptun

Neptun NPHW 5500 Bedienungsanleitung

Sensidyne

Sensidyne Gilian BDX-II Montage- und Bedienungsanleitung

Draper

Draper 47808 Bedienungsanleitung

Trolla

Trolla 12820 Bedienungsanleitung

Sunfab

Sunfab SVH Series Bedienungsanleitung

WilTec

WilTec 50740 Bedienungsanleitung

Fieldmann

Fieldmann FVC 5015 EK Bedienungsanleitung

Everbilt

Everbilt EFSUB5-122HD Bedienungsanleitung

Graco

Graco Husky 3300e Bedienungsanleitung

esotec

esotec 101018 Bedienungsanleitung

moyno

moyno 2000 CC Bedienungsanleitung

Becker

Becker BASIC VASF 2.80/1-0.AC230 Bedienungsanleitung

Sykes AmeriPumps

Sykes AmeriPumps GP100M Fehlerbehebungshandbuch

DUROMAX

DUROMAX XP WX Series Bedienungsanleitung

BRINKMANN PUMPS

BRINKMANN PUMPS SBF550 Bedienungsanleitung

Franklin Electric

Franklin Electric IPS Bedienungsanleitung

Xylem

Xylem e-1532 Series Bedienungsanleitung

Milton Roy

Milton Roy PRIMEROYAL Bedienungsanleitung