Kramer VM-212DT Bedienungsanleitung

VM-212DT Quick Start (P/N: 2900-300878QS REV 2)

P/N:

2900- 300878QS

Rev:

Scan for full manual

VM-212DT Quick Start Guide

This guide helps you install and use your VM-212DT for the first time.

Go to www.kramerav.com/downloads/VM-212DT to download the latest user manual and check if

firmware upgrades are available.

Step 1: Check what’s in the box

VM-212DT HDMI/HDBT Switcher/DA

4 Rubber feet

1 Set of rack ears

1 Power cord

1 Quick start guide

Step 2: Get to know your VM-212DT

Feature

Function

IR LED

Lights yellow when receiving signals from the IR remote control sensor.

IR Remote Control Sensor

Sensor for an IR transmitter. IR data is routed according to the IR routing configuration.

POWER LED

Lights green when the unit receives power.

VOLUME

Buttons

▼ Down

Press to decrease the audio volume.

▲ Up

Press to increase theaudio volume.

INPUT Button

Press to toggle between HDMI Input 1 and HDBT Input 2. Lights red when the input is valid,

selected and routing to an output(s).

1 HDMI LED

Lights green when HDMI 1 Input is selected.

2 HDBT LED

Lights green when HDBT 2 Input is selected.

EDID Buttons

READ

Press to read the selected EDID to both inputs (see Step 6).

SELECT

Press to cycle through the EDID sources, (default, external, and each output) from which to

read the EDID. The relevant LED lights green (see Step 6).

OUTPUT LEDs 1to 3

In normal operation mode: lights green when an acceptor is connected to the output.

In EDID mode: the relevant LEDs light during EDID setup (see Step 6).

EDID TYPE

LEDs

DEFAULT

Lights green when the default EDID is selected (see Step 6).

EXT.

Lights green when an externalEDID is selected.

OUTPUT

Lights green when one of the output EDIDs is selected.

Feature

Function

INPUT 1 HDMI Local Input

Connect to the HDMI source.

INPUT 2 HDBT Remote Input

Connect to the remote HDBT transmitter, (for example, the WP-20 or TP-580Txr).

OUTPUT 1 HDMI Local Output

Connect to the HDMI acceptor.

OUTPUT HDBT 2 Connector

OUTPUT HDBT Connectors.

OUTPUT HDBT 3 Connector

AUDIO OUT 3.5mm Mini Jack

Connect to the analog audio acceptor.

REMOTE IR 3.5mm Mini Jack

For future use.

IR 3.5mm Mini Jack

Connect to the remote IR sensor/emitter.

RS-232 DATA 3-pin Terminal Block

Connect to the device to be controlled via RS-232.

RS-232 CONTROL 3-pin Terminal Block

Connect to the serial controller to control the VM-212DT.

REMOTE 3-pin Terminal Block

For future use.

SETUP 4-way DIP-switch

Used to set the device behavior (see Step 7).

ETHERNET RJ-45 Connector

Connect to a remote network controller via a LAN.

RESET Switch

Press and hold while powering on the device to reset to factory default parameters.

PROG Mini USB Connector

Connect to a PC to perform firmware upgrades.

Power Connector, Fuse, and Switch

Connect to the power cord and the mains electricity.

Step 3: Install VM-212DT

Install VM-212DT using one of the following methods:

Remove the three screws from each side of the unit, reinsert those screws through therack ears

and mount on a 19" rack.

Attach the rubber feet and place the unit on a flat surface.

Step 4: Connect the inputs and outputs

Always switch OFF the power on each device before connecting it to your VM-212DT. For best results, we recommend that

you always use Kramer high-performance cables to connect AV equipment to VM-212DT.

Step 5: Connect the power

Connect the power cord to VM-212DT and plug it into the mains electricity.

Safety Instructions

Caution:

There are no operator serviceable parts insidethe unit.

Warning:

Use only the power cord that is supplied with the unit.

Warning:

Do not open the unit. High voltages can cause electrical shock! Servicing by qualified personnel only.

Warning:

Disconnect the power and unplug the unit from the wall before installing.

See www.KramerAV.com for updated safety information.

Step 6: Operate VM-212DT

Operate VM-212DT via:

Front panel buttons

Remotely, by RS-232 serial commands

transmitted by a touch screen system, PC,

or other serial controller

Embedded web pages via the Ethernet

RS-232 Control

Protocol 3000

Baud Rate:

115200

Data Bits:

Stop Bits:

Parity:

None

Command Format:

ASCII

Example: (Get EDID support on specific input/output):

#GEDID?<SP>stage, stage_id <CR>

Default Ethernet Parameters

Device Name:

KRAMER_

Gateway:

192.168.0.1

DHCP:

OFF

TCP Port:

5000

IP Address:

192.168.1.39

UDP Port:

50000

Mask:

255.255.0.0

Acquiring the EDID using the front panel buttons:

1. Press the EDID SELECT button repeatedly until the required EDID source is selected, (either Default, Ext, or one of

the outputs).

The relevant EDID TYPE / OUTPUT LEDs light green.

2. Press the EDID READ button.

The EDID READ button lights red for a short while and the EDID is copied to the currently selected input. If the EDID

READ button flashes once, this indicates that the EDID was not read and the device reverts to the last stored EDID,

as indicated by the LEDs.

Note: If the EDID READ button is not pressed for a few seconds, the procedure is terminated and the device does not store a

new EDID.

Note: The EDID can also be acquired and modified using the embedded webpages or Kramer EDID Designer software.

Selecting an input:

Press the INPUT button to toggle between the inputs.

The relevant INPUT LED lights green.

Protocol 3000 Commands:

Command

Description

Command

Description

Protocol handshaking

LOGOUT

Cancel current permission level

AUD-LVL

Set/get audio level in specific amplifier

stage

MODEL?

Read device model

AV-SW-TIMEOUT

Set/get video auto-switch timeout

MUTE

Set/get audio mute

BUILD-DATE?

Read device build date

NAME

Set/get machine (DNS) name

CPEDID

Copy EDID data from the output to the

input

NAME-RST

Reset machine name to factory default

(DNS)

DIR

List files in device

NET-DHCP

Set/get DHCP mode

DISPLAY?

Get output HPD status

NET-GATE

Set/get gateway IP

DPSW-STATUS?

Get the DIP-switch status

NET-IP

Set/get IP address

ETH-PORT

Set/get Ethernet port protocol

NET-MAC?

Get MAC address

FACTORY

Reset to factory default configuration

NET-MASK

Set/get subnet mask

FPGA-VER?

Get current FPGA version

PASS

Set/get Password

FS-FREE?

Get file system free space

PING

Sends ICMP ECHO

GEDID

Read EDID data

PROT-VER?

Get device protocol version

GET

Get file

RESET

Reset device

HDCP-MOD

Set/get HDCP mode

ROUTE

Set/get layer routing

HDCP-STAT?

Get HDCP signal status

SECUR

Start/Stop Security

HELP?

Get command list

SIGNAL?

Get input signal lock status

LDEDID

Write EDID data to input

SN?

Read device serial number

Set/get protocol permission

VERSION?

Read device firmware version

Using the Embedded Web Pages

The VM-212DT can beoperated remotely using the embedded web

pages. Access the web pages from the control computer using a web

browser and an Ethernet connection.

Before attempting to connect:

Ensure that your browser is supported.

Ensure that JavaScript is enabled.

Note: In the event that a Web page does not update correctly, clear

your Web browser’s cache.

To browse the VM-212DT web pages:

1. Open your Internet browser.

2. Type the IP number of the device (default = 192.168.1.39) in

your browser.

If authentication is enabled, the Authentication Required window

appears.

3. Enter the valid username and password to access the web

pages (default = User Name: Admin; Password: Admin).

The Web Cache message appears.

4. Click OK.

The Switching page appears

Item

Description

Page Selection Panel

Click one of the buttons to select a page.

Page Selection Panel Hide/Reveal Button

Click the arrowto open or close the page selection panel.

Switching Selection

Click one of the buttonsto select an input.

Mute Button

Click to mute/unmute the audio.

Analog Output Volume Control

Click and drag the slider to control the audio volume.

Security Indicator

Indicates whether security is enabled (locked) or disabled(unlocked).

Full Screen Button

Click to maximize the page.

Step 7: Setting the DIP Switches

Set the DIP-switches using the table on

the right. The ON/OFF positions are as

follows:

Switch down = ON

Switch up = OFF

Feature

Switch State

IR modulation selection

Off—Disable IR

On—Enable IR modulation

Extra range

Off—Disable extra range

On—Enable extra range

Compressed audio/

Audio de-embedding

Off—De-embed audio

On—Enable compressed audio

Reserved

Andere Handbücher für VM-212DT

Andere Kramer Verstärker Handbücher

Kramer

Kramer VM-24H Bedienungsanleitung

Kramer

Kramer VP-4 Bedienungsanleitung

Kramer

Kramer VP-242 Bedienungsanleitung

Kramer

Kramer 106 Bedienungsanleitung

Kramer

Kramer VP-400 Bedienungsanleitung

Kramer

Kramer VP-22 Bedienungsanleitung

Kramer

Kramer VA-4 Bedienungsanleitung

Kramer

Kramer 901 Bedienungsanleitung

Kramer

Kramer PT-102AN Bedienungsanleitung

Kramer

Kramer VM-24H Bedienungsanleitung

Kramer

Kramer VM-10xl Bedienungsanleitung

Kramer

Kramer 104LN Bedienungsanleitung

Kramer

Kramer VP-10 Bedienungsanleitung

Kramer

Kramer VM-30AV Bedienungsanleitung

Kramer

Kramer VP-200XLN Bedienungsanleitung

Kramer

Kramer VS-406 Bedienungsanleitung

Kramer

Kramer 914 Bedienungsanleitung

Kramer

Kramer VM-3S Bedienungsanleitung

Kramer

Kramer VP-200AK Bedienungsanleitung

Kramer

Kramer 105V Bedienungsanleitung

Kramer

Kramer VP-108 Bedienungsanleitung

Kramer

Kramer TOOLS VM-2C Bedienungsanleitung

Kramer

Kramer VM-2HDCPxl Bedienungsanleitung

Kramer

Kramer VM-80A Bedienungsanleitung

Beliebte Verstärker Handbücher anderer Marken

ASTRO

ASTRO HVO V40 P Bedienungsanleitung

Marantz

Marantz SUPERSCOPE BLA-545 Montageanleitung

NAD

NAD CI980 Bedienungsanleitung

Technics

Technics SE-CH770 Bedienungsanleitung

Harman Kardon

Harman Kardon HK6300 Bedienungsanleitung

NAD

NAD T975 Bedienungsanleitung

McIntosh

McIntosh MA6850 Bedienungsanleitung

Electro-Harmonix

Electro-Harmonix ENGLISH MUFF’N Bedienungsanleitung

Viatron

Viatron Autrix Bedienungsanleitung

GME

GME GA9800 Bedienungsanleitung

Atlas

Atlas CP700 Bedienungsanleitung

Roland

Roland KC-1000 Bedienungsanleitung

Pyle

Pyle PFMRA350BW Bedienungsanleitung

Advantage

Advantage S-250 Bedienungsanleitung

IRT Electronics

IRT Electronics DVA-3007 Bedienungsanleitung

Dimavery

Dimavery BA-100 Series Bedienungsanleitung

Sony

Sony XM-S400D Bedienungsanleitung

Schertler

Schertler ROY X Bedienungsanleitung