Kramer KDS-SW2-EN7 Bedienungsanleitung

KDS-SW2-EN7 Quick Start

P/N:

2900- 301547QS

Rev:

Scan for full manual

KDS-SW2-EN7 Quick Start Guide

This guide helps you installand use your KDS-SW2-EN7 for the first time.

Go to www.kramerav.com/downloads/KDS-SW2-EN7to download the latest user manual andcheck if

firmware upgrades are available.

Step 1: Check what’s in the box

KDS-SW2-EN7 2x1 4K AVoIP Switcher Encoder

2 Bracket sets

1 Quick start guide

Step 2: Get to know your KDS-SW2-EN7

Feature

Function

HDMI IN Connector

Connect to an HDMI acceptor.

USB-C IN Port

Connect to a USB-C source.

•When powered by a Kramer 24V power supply (optional), charges sources (that

support USB Power Delivery 2.0) up to 60W.

LCD Display

Use for device configuration such as input selection, unique channel/AV stream setting

and EDID.

Menu Navigation

Button



Press to return to the previous menu.



Press to move up to the next configuration parameter.



Press to go to the next menu.



Press to move down to the next configuration parameter.

Enter

Press to accept changes.

LINK LED

See LED Functionality.

NET LED

See LED Functionality.

ON LED

See LED Functionality.

Feature

Function

24V/5A DC Connector

Connect to the power adapter (purchased separately).

RESET Recessed Button

Press and hold for 10 seconds to reset the device to its factory default values. All LEDs flash.

LAN MEDIA 1G(PoE) RJ-45

Port

Unicast: connect for streaming either directly to a decoder or via LAN.

Multicast: connect to multiple decoders or connect to one decoder to which multiple

decoders are daisy-chained via SERVICE (1G) port.

Feature

Function

LAN SERVICE 1G RJ-45

Port

Used optionally for physical separation between AV and command streams to separate LAN

for security and reliability purposes.

RS-232 3-pin Terminal Block

Connector

Connect to an RS-232 device to use as a Gateway and bi-directional signal extension (even

when no AV signal is extended).

AUDIO IN/OUT 5-pin

Terminal Block Connector

Connect to a balanced analog stereo audio source/acceptor.

IR 3.5 Mini Jack

Connect to an IR sensor or emitter for bi-directional signal extension (even when no AV

signal is extended). Expected voltage for IR receiver - (3.3V).

USB Type A Charging Ports

(1 and 2)

Connect to USB devices, for example, to a speakerphone and webcam.

HOST USB Type B Port

Connect to a USB host.

HDMI OUT Connector

Connect to loop the signal.

LED Functionality

KDS-SW2-EN7 LEDs function as follows:

LED

Color

Definition

LINK LED

Lights Green

A link is established between KDS-SW2-EN7 and the decoder is

transmitting A/V signals.

Flashes Green

A signal is established, and a problem is detected

NET LED

Off

No IP address is acquired.

Lights green

A valid IP address has been acquired.

Flashes Green very fast (for 60sec)

A device identification command is sent (Flag me).

Lights Yellow

Device falls back to default IP address.

Lights Red

Security is blocking IP access.

ON LED

Flashes Red

On fallback address acquiring, device ‘ON’ LED flashes continuously in

slow 0.5/10sec cadence

Lights Green

When power is on.

Flashes Green Slowly

Device is in standby mode.

Flashes green fast

FW is downloaded in the background.

Flashes Green very fast (for 60sec)

A device identification command is sent (Flag me).

Lights Yellow

Device falls back to default IP address

Lights Red

Security is blocking IP access.

Post reboot, all LEDs light for 3 seconds then return to their normal LED display mode.

Step 3: Mount KDS-SW2-EN7

Install KDS-SW2-EN7 using one of the following methods:

•Attach the rubber feet and place the unit on a flat surface.

•Fasten a bracket (included) on each side of the unit and attach it to a flat surface

(see www.kramerav.com/downloads/KDS-SW2-EN7).

•Mount the unit in a rack using the recommended rack adapter

(see www.kramerav.com/product/KDS-SW2-EN7).

•Ensure that the environment (e.g., maximum ambient temperature &

air flow) is compatible for the device.

•Avoid uneven mechanical loading.

•Appropriate consideration of equipment nameplate ratings should be

used for avoiding overloading of the circuits.

•Reliable earthing of rack-mounted equipment should be maintained.

•Maximum mounting height for the device is 2 meters.

Step 4: Connect inputs and outputs

Always switch OFF the power on each device before connecting it to your KDS-SW2-EN7 and KDS-DEC7.

KDS-SW2-EN7 and KDS-DEC7 can stream 4K video, requiring a gigabit Ethernet switch for high quality performance, since the

maximum momentary transfer rate can reach 850Mbps. We recommend using AVoIP Ethernet switches that support: Multicast

forwarding or filtering, IGMP Snooping, IGMP Querier, IGMP snooping fast leave and Jumbo frame (8000 bytes or larger).

Connecting the audio input/output

To a balanced

stereo audio

source/acceptor:

To an unbalanced

stereo audio

acceptor:

To an unbalanced

stereo audio source:

To achieve specified extension distances, use the recommended Kramer cables available at www.kramerav.com/product/KDS-SW2-EN7.

Using third-party cables may cause damage!

Step 5: Connect power

By-default, the device uses PoE for powering the device.

Optionally, you can separately purchase a power adapter to connect to the product and plug into the mains electricity.

Safety Instructions (See www.kramerav.com for updated safety information)

Caution:

•For products with relay terminals and GPIO ports, please refer to the permitted rating for an external connection, located next to the terminal or in the User Manual.

•There are no operator serviceable parts inside the unit.

Warning:

•Use only the power cord that is supplied with the unit.

•Disconnect the power and unplug the unit from the wall before installing.

Step 6: Operate KDS-SW2-EN7

Allocating the IP Address via LCD screen menu

KDS-SW2-EN7 IP default address is 192.168.1.39. By default, DHCP is enabled, and assigns an IP address to the device. If

DHCP Server is not available, for example, in case a device is connected directly to the laptop, that device gets the default IP

address. If this IP addresses is already in use, the system searches for a random unique IP in the range of 192.168.X.Y. the

allocated IP address can be identified using the LCD screen menu.

To allocate the IP address via LCD screen Menu:

1. Connect the device to the 24V DC power adapter and connect the adapter to the mains electricity. The ON LED lights

green, and the LINK LED flashes (indicating that no streaming activity is detected).

2. Use the Navigation button to view the assigned IP address on the LCD screen:

▪DEV STATUS > LAN1 Status

▪DEV STATUS > LAN2 Status (if the Service port connected as well).

Setting Channel Number

Each encoder requires a unique channel number, and the connected decoders should be tuned to that encoder channel. You

can set the channel number via the LCD screen menu or the embedded web pages.

To set the channel number for KDS-SW2-EN7 via LCD screen menu:

1. Connect the device to the 24V DC power adapter and connect the adapter to the mains electricity. The ON LED lights

green, and the LINK LED flashes (indicating that no streaming activity is detected).

2. In the LCD screen menu, go to DEV SETTINGS > CH DEFINE.

3. Change channel number using arrow buttons and set a unique channel number.

4. Press Enter to save your selection.

To set the channel number via web pages:

1. Connect the KDS-SW2-EN7 Ethernet port to the network and power the device.

2. Access the embedded web pages.

3. In the Main page:

For KDS-SW2-EN7:

▪Go to AV Routing page.

▪Select Channel ID and define the channel ID number.

Andere Handbücher für KDS-SW2-EN7

Inhaltsverzeichnis

Andere Kramer Schalten Handbücher

Kramer

Kramer VP-440 Bedienungsanleitung

Kramer

Kramer MV-6 Bedienungsanleitung

Kramer

Kramer 6241HD Bedienungsanleitung

Kramer

Kramer VP-725DSA Bedienungsanleitung

Kramer

Kramer VP-214DS Bedienungsanleitung

Kramer

Kramer VP-770 Bedienungsanleitung

Kramer

Kramer ProScale VP-728 Bedienungsanleitung

Kramer

Kramer VS-21T Bedienungsanleitung

Kramer

Kramer ProScale VP-728 Bedienungsanleitung

Kramer

Kramer VP-438 Bedienungsanleitung

Kramer

Kramer VS-33Vxl Bedienungsanleitung

Kramer

Kramer VP-444 Bedienungsanleitung

Kramer

Kramer VM-218DTxr Bedienungsanleitung

Kramer

Kramer DIP-31M Bedienungsanleitung

Kramer

Kramer VM-22H Bedienungsanleitung

Kramer

Kramer ASPEN-32UFX Bedienungsanleitung

Kramer

Kramer VS-21HDMI Bedienungsanleitung

Kramer

Kramer DigiTOOLS VS-41USB Bedienungsanleitung

Kramer

Kramer VS-311H Bedienungsanleitung

Kramer

Kramer VP-311DVI Bedienungsanleitung

Kramer

Kramer VP-28 Bedienungsanleitung

Kramer

Kramer VP-558 Bedienungsanleitung

Kramer

Kramer TP-590T Bedienungsanleitung

Kramer

Kramer VP-796A Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung