Kreg 500 Series Bedienungsanleitung
OWNER’S MANUAL
We’re here to help.
We want you to have an exceptional project building experience.
If you have questions or need support, please get in touch.
Tell us about your experience.
Your opinion counts. And we’re always looking for ways to improve.
Share your feedback so we can keep growing and innovating for you.
www.kregtool.com/feedback
WARNING Every user must read and follow instructions and safety precautions in this manual.
Failure to do so could result in serious injury. Save manual for future reference.
English 2
French (N. America) 11
Spanish (N. America) 21
Kreg Pocket-Hole Jig 500-Series
Manual applies to all 500-Series Pocket-Hole Jigs
2
Safety Precautions
WARNING Before using a power tool with this product, read, and follow the
tool manufacturer’s instructions and safety precautions in addition to the safety
precautions below to reduce risk of serious injury from hazards such as re, electric
shock, or rotating drill bit.
■Always wear personal protective equipment recommended by the manufacturer of
the power tool you are using, such as eye, hearing, or respiratory protection.
■The drill bit is sharp. Handle with care.
■Do not allow familiarity gained from frequent use of your tools to replace safe
work practices. A moment of carelessness is sufcient to cause severe injury.
■Avoid awkward hand positions where a sudden slip could cause contact with the
rotating bit.
■When drilling, always ensure workpiece is clamped securely. It is dangerous to
hold workpiece in place by hand.
WARNING Do not operate this tool or any machinery while under the inuence of
drugs, alcohol, or medications.
WARNING This product can expose you to chemicals including Acrylonitrile and
other chemicals, which are known to the State of California to cause cancer and
reproductive harm. For more information go to www.P65Warnings.ca.gov.
Table of Contents
Safety Precautions . . . . . . . . . .2
Pre-Operation . . . . . . . . . . . . . 3
Product Description . . . . . . . . . 3
Operation - Drilling Your First
PocketHole . . . . . . . . . . . . . . 4
Operation - Drilling and Driving
Pocket-HoleScrews . . . . . . . . . 6
Using the Quick Reset Feature . . . . 8
Using Your Kreg Jig. . . . . . . . . . 9
Care and Cleaning . . . . . . . . . . 9
Accessories . . . . . . . . . . . . . . 9
3
Pre-Operation
Review this section before you begin. Ensure you have all tools/materials on hand
and compare the package with the items listed in the Hardware Included and Product
Description sections. If any item appears missing or lost, do not use this product.
Contact Technical Support or return product to place of purchase.
Product Description
A
A1
C
D
E
B
Part Description Part Description
A
KPHJ520 Pocket-Hole Jig A1-Drill
Guide with GripMaxx™ anti-slip
surface
D Easy-set stop collar
B Easy-set pocket-hole drill bit E 6" Driver bit
C Material thickness gauge/Hex wrench
Note This product may include sample screws and a clamp, depending upon the
model you have purchased.
4
Operation - Drilling Your First PocketHole
1 Determine the Material Thickness and Set the Stop Collar
a. Use the material thickness gauge (C) to determine the material thickness range.
b. Set the stop collar (D) by placing it on the drill bit (B) and aligning the window of
the stop collar (D) with the material thickness range determined in step a.
c. Use the hex wrench (C) to lock the stop collar (D) into place on the drill bit (B).
C
B
D
C
2 Adjust the Drill Guide
Adjust the drill guide by pressing both tabs (1) on the guide and sliding it to the
measurement setting (2) that corresponds with your material measurement.
2
1
5
3 Position Your Workpiece
There are two different methods for aligning your Kreg Jig with your workpiece:
a. Align the center line of any pocket-hole guide (numbers 1, 2, or 3) with the
desired location on your workpiece. For wider panels (over 3-1/2" wide) pocket
holes should be placed 5/8" to 1-1/2" from each edge of the workpiece and then
every 6" to 8".
b. Use the board centering marks (letters A, B, or C) to center two pocket holes on
the workpiece ranging in width from 1-1/4" to 3-1/2" wide. See the table below
for details on each size range.
1 2 3 A B C
Board Width Center Mark Drill Guide
1-1/4" to 1-3/4" C 2 and 3
1-3/4" to 2-3/8" A 1 and 2
2-3/8" to 3-1/2" B 1 and 3
c. Place your workpiece in the jig and squeeze the handle (4) repeatedly to clamp
you workpiece securely into the jig. Proceed to the Operation - Drilling and
Driving Pocket-Hole Screws section to start drilling.
Tip To drill pocket holes on similar
workpieces at a faster pace, see the
Using the Quick Reset Feature section
of the manual.
Tip The handle can be rotated to provide
a comfortable hand position. 4
6
Operation - Drilling and Driving
Pocket-HoleScrews
1 Drill Pocket Holes
WARNING When drilling, always ensure the workpiece is clamped securely.
a. Place your prepared drill bit (B) with stop collar (D) into your drill.
b. Insert your drill bit into the drill guide (1) and bring your drill up to speed before
contacting the workpiece to ensure correct rotation of the drill bit.
c. Drill until the stop collar (D) stops going any deeper due to contact between the
stop collar (D) and drill guide (1). Remove the drill bit (B) from the drill guide while
the drill bit is still rotating.
d. When done drilling pocket hole(s), pull the trigger (2) to release the clamping
pressure and remove your workpiece.
1
D
B
2
7
2 Drive Screws
a. Ensure you are using the correct screw size according to this chart:
Gauged Material
Thickness
Easy-Set
Stop Collar
Material
Thickness Stop
Screw Length
1/2 Range 1/2 1/2 1" (25 mm)
3/4 Range 3/4 3/4 1-1/4" (32 mm)
3/4 3/4 1-1/2" (38 mm)
1-1/2 Range 1½ 1½ 2-1/2" (64 mm)
For more information on screw selections, go to www.Kregtool.com/Screws or
simply scan the QR code on the side of your sample screw package.
Tip A 1" screw is recommended for most applications, but if your workpiece is
on the low end of the range, a 3/4" screw might be required to keep the screw tip
from protruding.
Note If your material thickness falls in the range, use the same setup
techniques as the 3/4" range with a 1-1/2" screw.
b. Clamp joints in place to ensure a better nished joint. These examples show face
joints and edge joints.
WARNING When drilling, always ensure the workpiece is clamped securely.
c. Place your screw on the driver tip (E), position the screw in the pocket hole, and
drive the screw until it is fully seated without overdriving.
E
E
E
E
8
Using the Quick Reset Feature
The Quick Reset feature allows you to drill pocket holes on multiple similar
workpieces by limiting the back and forth movement of the clamp for a faster clamp
and release of your workpiece. To use the Quick Reset feature:
a. Squeeze the handle (1) to clamp your workpiece securely in the jig.
b. Tighten the knob (2) by hand until it is tight.
c. Drill your pocket holes.
d. Pull the drill guide release (3) to move the clamp back just enough to release the
workpiece.
e. Align to your next hole location and squeeze the handle (1) two or three times to
quickly re-clamp.
f. Once nished with your similarly-sized workpieces, loosen the knob (2) and pull
the drill guide release (3) to return the clamp to its maximum opening.
2
13
9
Using Your Kreg Jig
a. Your Kreg Jig has been designed to
work in different orientations. You may
nd it more comfortable to work with
your Kreg Jig placed with the end of
the work surface and the handle up
in the air.
b. You can secure the jig in place on your
workbench using the Pocket-Hole Jig
Clamp (1) at the bottom of the jig.
Care and Cleaning
Periodically clean your tool by vacuuming any chips and wood dust.
Keep GripMaxx™ anti-slip surface clean and free of dust by wiping with a damp
cloth.
Accessories
KPHA530 Kreg Micro Drill Guide
KPHA760 Kreg
Bench Clamp
KPHA750 Pocket-Hole Jig Docking
Station
1
EXPLORE. BUILD. SHARE.
We’re makers just like you.
That’s why we love to see what you’re working on.
Share with the community and get inspired!
#madewithKreg
Get free plans, project resources, and more.
kregtool.com and buildsomething.com
01/2020 104904 V1
Inhaltsverzeichnis
Sprachen:
Andere Kreg Werkzeuge Handbücher
Kreg
Kreg Jig K4 Bedienungsanleitung
Kreg
Kreg KMA3225 Bedienungsanleitung
Kreg
Kreg K3 Bedienungs- und Wartungshandbuch
Kreg
Kreg FOREMAN DB210 Bedienungsanleitung
Kreg
Kreg KPHJ230 Bedienungsanleitung
Kreg
Kreg KHI-PULL-INT Bedienungsanleitung
Kreg
Kreg Rip-Cut KMA2685 Bedienungsanleitung
Kreg
Kreg r3 Bedienungs- und Wartungshandbuch
Kreg
Kreg Adaptive Cutting System Parallel Guides Bedienungsanleitung
Kreg
Kreg Klamp Plate Service-Handbuch
Kreg
Kreg K4 Bedienungsanleitung
Kreg
Kreg KMA4000 Bedienungsanleitung
Kreg
Kreg PRS1000 Bedienungsanleitung
Kreg
Kreg KPHJ310 Bedienungsanleitung
Kreg
Kreg Jig R3 Bedienungsanleitung
Kreg
Kreg Track Clamp Bedienungsanleitung
Kreg
Kreg DB110 Bedienungs- und Wartungshandbuch
Kreg
Kreg KCS-DFMT Bedienungsanleitung
Kreg
Kreg KFPCHB Bedienungsanleitung
Kreg
Kreg R3-INT Bedienungsanleitung
