KROHNE OPTISOUND 3020 Bedienungsanleitung

OPTISOUND 3020 Quick setup guide

Ultrasonic Level Transmitter

Foundation Fieldbus

Contents

OPTISOUND 3020 • Foundation Fieldbus

62690-EN-220310

Contents

1 For your safety ......................................................................................................................... 3

1.1 Authorised personnel ....................................................................................................... 3

1.2 Appropriate use................................................................................................................ 3

1.3 Warning about incorrect use............................................................................................. 3

1.4 General safety instructions............................................................................................... 3

1.5 EU conformity................................................................................................................... 3

1.6 NAMUR recommendations .............................................................................................. 4

2 Product description ................................................................................................................. 5

2.1 Conguration.................................................................................................................... 5

3 Mounting................................................................................................................................... 6

3.1 Mounting instructions ....................................................................................................... 6

4 Connecting to power supply................................................................................................... 7

4.1 Connection procedure...................................................................................................... 7

4.2 Wiring plan, single chamber housing................................................................................ 8

4.3 Wiring plan, double chamber housing .............................................................................. 8

5 Set up with the display and adjustment module PLICSCOM .............................................. 9

5.1 Insert display and adjustment module.............................................................................. 9

5.2 Setup steps ...................................................................................................................... 9

5.3 Menu schematic............................................................................................................. 12

6 Supplement ............................................................................................................................ 14

6.1 Technical data ................................................................................................................ 14

Information:

This quick setup guide enables quick setup and commissioning of

your instrument.

Youcanndfurtherinformationinthecorresponding,comprehensive

operating instructions as well as in the Safety Manual for instruments

withSILqualication.

Operating instructions OPTISOUND 3020 C - Foundation Field-

bus: Document-ID 51116

Editing status of the quick setup guide: 2022-03-07

1 For your safety

OPTISOUND 3020 • Foundation Fieldbus

62690-EN-220310

1 For your safety

1.1 Authorised personnel

All operations described in this documentation must be carried out

onlybytrained,qualiedpersonnelauthorisedbytheplantoperator.

Duringworkonandwiththedevice,therequiredpersonalprotective

equipment must always be worn.

1.2 Appropriate use

OPTISOUND3020Cisasensorforcontinuouslevelmeasurement.

Youcannddetailedinformationabouttheareaofapplicationin

chapter " Product description".

Operational reliability is ensured only if the instrument is properly

usedaccordingtothespecicationsintheoperatinginstructions

manual as well as possible supplementary instructions.

1.3 Warning about incorrect use

Inappropriateorincorrectuseofthisproductcangiverisetoapplica-

tion-specichazards,e.g.vesseloverllthroughincorrectmounting

oradjustment.Damagetopropertyandpersonsorenvironmental

contaminationcanresult.Also,theprotectivecharacteristicsofthe

instrument can be impaired.

1.4 General safety instructions

Thisisastate-of-the-artinstrumentcomplyingwithallprevailing

regulationsanddirectives.Theinstrumentmustonlybeoperatedina

technicallyawlessandreliablecondition.Theoperatorisresponsi-

ble for the trouble-free operation of the instrument. When measuring

aggressiveorcorrosivemediathatcancauseadangeroussituation

if the instrument malfunctions, the operator has to implement suitable

measures to make sure the instrument is functioning properly.

The safety instructions in this operating instructions manual, the na-

tionalinstallationstandardsaswellasthevalidsafetyregulationsand

accidentpreventionrulesmustbeobservedbytheuser.

Forsafetyandwarrantyreasons,anyinvasiveworkonthedevice

beyond that described in the operating instructions manual may be

carried out only by personnel authorised by the manufacturer. Arbi-

traryconversionsormodicationsareexplicitlyforbidden.Forsafety

reasons,onlytheaccessoryspeciedbythemanufacturermustbe

used.

Toavoidanydanger,thesafetyapprovalmarkingsandsafetytipson

thedevicemustalsobeobserved.

1.5 EU conformity

ThedevicefullsthelegalrequirementsoftheapplicableEUdirec-

tives.ByaxingtheCEmarking,weconrmtheconformityofthe

instrumentwiththesedirectives.

The EU conformity declaration can be found on our homepage.

1 For your safety

OPTISOUND 3020 • Foundation Fieldbus

62690-EN-220310

1.6 NAMUR recommendations

NAMUR is the automation technology user association in the process

industry in Germany. The published NAMUR recommendations are

acceptedasthestandardineldinstrumentation.

ThedevicefullstherequirementsofthefollowingNAMURrecom-

mendations:

• NE 21 – Electromagnetic compatibility of equipment

• NE43–Signallevelforfaultinformationfrommeasuringtransduc-

ers

• NE53–Compatibilityofelddevicesanddisplay/adjustment

components

For further information see www.namur.de.

2 Product description

OPTISOUND 3020 • Foundation Fieldbus

62690-EN-220310

2 Product description

2.1 Conguration

Thetypelabelcontainsthemostimportantdataforidenticationand

use of the instrument:

• Instrument type

• Articleandserialnumberdevice

• Article number documentation

• Technicaldata:Approvals,processtemperature,processtting/

material,signaloutput,voltagesupply,protection

Type label

3 Mounting

OPTISOUND 3020 • Foundation Fieldbus

62690-EN-220310

3 Mounting

3.1 Mounting instructions

The reference plane for the measuring range is the lower edge of the

transducer.

Make sure that a minimum distance from the reference plane - the

so-calleddeadzone,inwhichmeasurementisnotpossible-is

maintained.Theexactvalueofthedeadzoneisstatedinchapter"

Technical data".

Fig. 1: Minimum distance to the max. level

1 blocking distance

2 Reference plane

Mountthesensoratleast200mm(7.874in)awayfromthevessel

wall.

> 200 mm

Fig. 2: Mounting on round vessel tops

1 Reference plane

2 Vessel center or symmetry axis

Reference plane for

measuring range

Mounting

4 Connecting to power supply

OPTISOUND 3020 • Foundation Fieldbus

62690-EN-220310

4 Connecting to power supply

4.1 Connection procedure

Proceed as follows:

1. Unscrew the housing lid

2. Ifadisplayandadjustmentmoduleisinstalled,removeitbyturn-

ing it to the left

3. Loosencompressionnutofthecableglandandremoveblind

plug

4. Removeapprox.10cm(4in)ofthecablemantle,stripapprox.

1cm(0.4in)ofinsulationfromtheendsoftheindividualwires

5. Insert the cable into the sensor through the cable entry

6. Lifttheopeningleversoftheterminalswithascrewdriver(see

following illustration)

7. Insert the wire ends into the open terminals according to the wir-

ing plan

Fig. 3: Connection steps 6 and 7

8. Pressdowntheopeningleversoftheterminals,youwillhearthe

terminal spring closing

9. Check the hold of the wires in the terminals by lightly pulling on

them

10. Connect the shielding to the internal ground terminal, connect the

externalgroundterminaltopotentialequalisation

11. Tighten the compression nut of the cable entry gland. The seal

ring must completely encircle the cable

12. Screw the housing lid back on

Theelectricalconnectionisnished.

4 Connecting to power supply

OPTISOUND 3020 • Foundation Fieldbus

62690-EN-220310

4.2 Wiring plan, single chamber housing

I2C

Display

12 5678

Fig. 4: Wiring plan - single chamber housing

1 Voltage supply, signal output

4.3 Wiring plan, double chamber housing

I2C

Fig. 5: Wiring plan - double chamber housing

1 Voltage supply, signal output

Wiring plan

5 Set up with the display and adjustment module PLICSCOM

OPTISOUND 3020 • Foundation Fieldbus

62690-EN-220310

5 Set up with the display and adjustment

module PLICSCOM

5.1 Insert display and adjustment module

The display and adjustment module can be inserted into the sensor

andremovedagainatanytime.Itisnotnecessarytointerruptthe

voltagesupply.

Proceed as follows:

1. Unscrew the housing lid

2. Place the display and adjustment module in the desired position

ontheelectronics(fourpositionsin90°osetcanbeselected)

and turn to the right until it clicks into place.

3. Screw housing lid with inspection window tightly back on

Disassemblyiscarriedoutinreverseorder.

The display and adjustment module is powered by the sensor, an ad-

ditional connection is not necessary.

Fig. 6: Insert display and adjustment module in the single chamber housing

Note:

Ifyouintendtoretrottheinstrumentwithadisplayandadjustment

moduleforcontinuousmeasuredvalueindication,ahigherlidwithan

inspection glass is required.

5.2 Setup steps

1. Go to the menu " Basic adjustment"viathedisplayandadjust-

ment module.

Mount/dismount display

and adjustment module

Set parameters

5 Set up with the display and adjustment module PLICSCOM

OPTISOUND 3020 • Foundation Fieldbus

62690-EN-220310

▶Basicadjustment

Display

Diagnostics

Service

Info

2. Carry out the adjustment in the menu items " Min. adjustment"

and " Max. adjustment".

Max.adjustment

100.00 %

1.000 m(d)

2.000 m(d)

Min. adjustment

0.00 %

5.000 m(d)

4.000 m(d)

3. Select in the menu item " Medium" the medium of your applica-

tion,forexample"Aqueous solution".

Medium

Liquid

4. Select in the menu item " Application"thevessel,theapplication

andthevesselform,forexample,"Storage tank".

Vessel shape

Storage tank

The sensor measures the distance from the sensor to the medium

surface.Forindicationofthereallevel,anallocationofthemeasured

distance to the percentage height must be carried out.

Theactuallevelisthencalculatedonthebasisoftheseentered

values.Atthesametime,theoperatingrangeofthesensorislimited

frommaximumrangetotherequestedrange.

Parameter adjustment

Inhaltsverzeichnis

Andere KROHNE Sender Handbücher

KROHNE

KROHNE OPTIWAVE 7300 C Verdrahtungsschema

KROHNE

KROHNE OPTIWAVE 5200 C/F Verdrahtungsschema

KROHNE

KROHNE OPTISOUND 3030 C Bedienungsanleitung

KROHNE

KROHNE OPTISOUND 3010 C Bedienungsanleitung

KROHNE

KROHNE OPTIFLEX 1300 C Verdrahtungsschema

KROHNE

KROHNE OPTIWAVE X500 Verdrahtungsschema

KROHNE

KROHNE OPTIWAVE 1010 Bedienungsanleitung

KROHNE

KROHNE OPTISOUND3020 C Bedienungsanleitung

KROHNE

KROHNE OPTIBAR 5060 Verdrahtungsschema

KROHNE

KROHNE OPTIBAR 5060 Verdrahtungsschema

KROHNE

KROHNE OPTIBAR 5060 eDP Verdrahtungsschema

KROHNE

KROHNE OPTISOUND 3020 C Bedienungsanleitung

KROHNE

KROHNE OPTISOUND 3020 C Bedienungsanleitung

KROHNE

KROHNE OPTISOUND 3030 C Bedienungsanleitung

KROHNE

KROHNE OPTIBAR P 1010 Verdrahtungsschema

KROHNE

KROHNE TT 51 Series Bedienungsanleitung

KROHNE

KROHNE OPTIWAVE 1400 C Verdrahtungsschema

KROHNE

KROHNE PM 3050 Bedienungsanleitung

KROHNE

KROHNE OPTIFLEX 2200 C Verdrahtungsschema

KROHNE

KROHNE OPTISOUND 3010 C Bedienungsanleitung

KROHNE

KROHNE OPTIWAVE 1010 Verdrahtungsschema

KROHNE

KROHNE OPTIBAR DP 3050 Bedienungsanleitung

KROHNE

KROHNE OPTISOUND 3010 C Bedienungsanleitung

KROHNE

KROHNE OPTIWAVE 400 Series Verdrahtungsschema

Beliebte Sender Handbücher anderer Marken

NIVELCO

NIVELCO EasyTREK SCA-300 Series Betriebsanleitung

Honeywell

Honeywell 5816WMBR Bedienungsanleitung

Kamstrup

Kamstrup READy MTU Betriebsanleitung

Omega

Omega ZW Series Bedienungsanleitung

ABB

ABB Field 264H Leitfaden

Alinco

Alinco DJ-V17T Bedienungsanleitung

Dejero

Dejero EnGo 3x Bedienungsanleitung

Rosemount

Rosemount 4600 Bedienungsanleitung

Speaka Professional

Speaka Professional 2342740 Bedienungsanleitung

trubomat

trubomat GAB 1000 Bedienungsanleitung

Teledyne Analytical Instruments

Teledyne Analytical Instruments LXT-380 Bedienungsanleitung

Rondish

Rondish UT-11 Bedienungsanleitung

MG 10JRE Bedienungsanleitung

Burkert

Burkert 8177 Bedienungsanleitung

Firetide

Firetide HotPort 3203 Handbuch

Tele Radio

Tele Radio T9-02 Bedienungsanleitung

Rotronic

Rotronic HygroFlex HF3 Series Bedienungsanleitung

Jamara

Jamara FCX6 Pro Tel Bedienungsanleitung