KTM RC 125 Handbuch

SETUP INSTRUCTIONS 2020

RC 125

Art. no. 3214236en

INTRODUCTION

*3214236en*

3214236en

01/2020

INTRODUCTION

Perform the work described in these setup instructions before the vehicle is delivered to the customer.

Read the setup instructions in their entirety before beginning work.

All specifications contained herein are non-binding. KTM Sportmotorcycle GmbH specifically reserves the right

to modify or delete technical specifications, prices, colors, forms, materials, services, designs, equipment, etc.,

without prior notice and without specifying reasons, to adapt these to local conditions, as well as to stop produc-

tion of a particular model without prior notice. KTM accepts no liability for delivery options, deviations from fig-

ures and descriptions, misprints, and other errors. The models portrayed partly contain special equipment that

does not belong to the regular scope of supply.

These setup instructions were written to correspond to the latest state of this series. We reserve the right to make

changes in the interest of technical advancement without at the same time updating this manual.

We shall not provide a description of general workshop methods. Likewise, safety rules that apply in a workshop

are not specified here. It is assumed that the work will be performed by a fully trained mechanic.

Reproduction, even in part, as well as copying of all kinds, is permitted only with the express written permission

of the copyright owner.

ISO 9001(12 100 6061)

KTM applies quality assurance processes that lead to the highest possible product quality as

defined in the ISO 9001 international quality management standard.

Issued by: TÜV Management Service

KTM Sportmotorcycle GmbH

Stallhofnerstraße 3

5230 Mattighofen, Austria

This document is valid for the following models:

RC 125 EU (F5003T1, F5003T2)

1 MEANS OF REPRESENTATION

1.1 Symbols used

The meaning of specific symbols is described below.

Indicates an expected reaction (e.g. of a work step or a function).

Indicates an unexpected reaction (e.g. of a work step or a function).

Indicates a page reference (more information is provided on the specified page).

Indicates information with more details or tips.

Indicates the result of a testing step.

Indicates a voltage measurement.

Indicates a current measurement.

Indicates a resistance measurement.

Indicates the end of an activity including potential rework.

1.2 Formats used

The typographical formats used in this document are explained below.

Proprietary name Indicates a proprietary name.

Name®Indicates a protected name.

Brand™ Indicates a brand available on the open market.

Underlined terms Refer to technical details of the vehicle or indicate technical terms, which

are explained in the glossary.

SETUP 2

2.1 Transport mode

H02713-01

This vehicle was blocked for transport in the software.

To operate the vehicle, the vehicle electronics must be enabled.

This process is conducted during initial setup in KTM Dealer.net.

Enabling ensures that the initial setup in KTM Dealer.net is docu-

mented.

Enabling can be performed either temporarily, e.g. for a test ride,

or permanently for vehicle handover.

Info

Make sure that the vehicle is permanently enabled before

handing it over to the customer.

2.2 Diagnostics connector

H01911-10

Diagnostics connector 1is located under the front rider's seat.

2.3 Unpacking and setting up the vehicle

A00034-10

–Remove the straps and the box.

S01886-01

–Remove the adhesive tape in the upper area of the motorcycle.

2 SETUP

A00043-10

–Roll down the film at the sides.

Info

To avoid damaging the motorcycle during unpacking,

leave the other films on the vehicle until you have fin-

ished work on the vehicle.

–Remove the separate enclosure and unpack it. Check the sepa-

rate enclosure for completeness.

Info

The procedure in the event of missing components is

described in the customer service manual.

–Check the vehicle for transport damage.

Info

The procedure in the event of transport damage is

described in the customer service manual.

S01885-10

Condition

Left and right handlebar stub not mounted.

–Remove protective film on the left and right handlebar

stub.

–Mount left and right handlebar stub on the upper triple

clamp.

Info

Make sure the cables and wiring are positioned cor-

rectly.

–Mount and tighten screws 1.

Guideline

Screw, handle-

bar stub

M6 8 Nm (5.9 lbf ft)

Loctite®243™

–Mount and tighten screws 2.

Guideline

Screw, anti-rotation

lock, handlebar

stub

M5 4 Nm (3 lbf ft)

–Position the clutch and hand brake assembly on the han-

dlebar stubs, mount the clamp screws and tighten.

–Attach the clutch cable to the clutch lever and slide on the

protection cap.

–Connect the cable of the brake light switch to the hand

brake assembly.

SETUP 2

S01888-10

–Position damping rubber 3on both sides.

–Join plug-in connector 4of the rear mirror on both sides.

–Position the rear mirror on both sides. Mount and tighten the

screws.

–Position all controls in their exact positions on the handlebar.

–Tighten all screws.

–Check the throttle cable play. ( p. 8)

H03807-10

–Make sure that the clutch cable is attached to the clutch

release lever and secured.

–Check the clutch lever play. ( p. 7)

F01048-10

–Mount rear reflector 5with spring washers 6on holding

plate 7.

–Mount the retaining plate on the license plate holder.

–Mount the license plate holder.

–Carefully loosen and remove the tension belt over the link fork.

Info

An assistant prevents the motorcycle from falling over.

–Carefully loosen and remove the tension belts around the lower

triple clamp.

The vehicle is released at the front.

–Together with an assistant, take the vehicle off the pallet.

Warning

Risk of injury Battery acid and battery gases cause

serious chemical burns.

–Keep 12 V batteries out of the reach of children.

–Wear suitable protective clothing and safety

glasses.

–Avoid contact with battery acid and battery gases.

–Keep sparks or open flames away from the 12 V

battery.

–Only charge 12 V batteries in well-ventilated

rooms.

–Rinse the affected area immediately with plenty of

water in the event of contact with the skin.

–Rinse eyes with water for at least 15 minutes and

consult a doctor immediately if battery acid and

battery gases get into the eyes.

–Fill the 12 V battery.

2 SETUP

Info

Read the notes in the 12 V battery accessory pack.

–Charge the 12-V battery. ( p. 11)

–Remove the front rider's seat. ( p. 9)

–Store the tool set below the seat.

–Remove the battery cover. ( p. 10)

S01889-01

–Remove spare key and KEYCODECARD and keep in a safe place

for the handover.

–Install the 12-V battery. ( p. 13)

–Remove the remaining film, padding, the corrugated card-

board, and the other packaging material.

–Refuel. ( p. 15)

–Prepare the vehicle according to the specifications in

KTM Dealer.net for handover to the customer.

WORK 3

3.1 Checking the clutch lever play

Note

Clutch damage If there is no free travel by the clutch lever, the clutch will begin to slip.

–Check the free travel of the clutch lever each time before using the motorcycle.

–Adjust the free travel of the clutch lever when necessary in accordance with the specification.

V00625-11

–Check the clutch lever for smooth operation.

–Move the handlebar to the straight-ahead position.

–Pull the clutch lever until resistance is perceptible, and deter-

mine the play in the clutch lever A.

Clutch lever play A1 … 3 mm (0.04 …

0.12 in)

» If the clutch lever play does not meet the specified value:

–Adjust play in the clutch lever. ( p. 7)

–Move the handlebar to and fro over the entire steering range.

The clutch lever play must not change.

» If the clutch lever play changes:

–Check the routing of the clutch cable.

3.2 Adjusting play in the clutch lever

V00672-10

–Move the handlebar to the straight-ahead position.

–Push back sleeve 1.

–Loosen lock nut 2.

–Adjust the play in the clutch level Aby turning adjusting

screw 3.

Guideline

Clutch lever play A1 … 3 mm (0.04 …

0.12 in)

–Tighten lock nut 2.

–Position bellows 1.

3 WORK

3.3 Checking throttle cable play

400192-11

–Check the throttle grip for smooth operation.

–Move the handlebar to the straight-ahead position. Turn the

throttle grip back and forth slightly and determine the play in

throttle cable A.

Throttle cable play A3 … 5 mm (0.12 … 0.2 in)

» If the throttle cable play does not meet specifications:

–Adjust the throttle cable play. ( p. 8)

Danger

Danger of poisoning Exhaust gases are toxic and inhal-

ing them may result in unconsciousness and death.

–Always make sure there is sufficient ventilation

when running the engine.

–Use effective exhaust extraction when starting or

running the engine in an enclosed space.

–Start the engine and let it run at idle speed. Move the handle-

bar to and fro over the entire steering range.

The idle speed must not change.

» If the idle speed changes:

–Check the throttle cable routing.

3.4 Adjusting throttle cable play

V00671-10

–Move the handlebar to the straight-ahead position.

–Push back sleeve 1.

–Loosen lock nut 2.

–Adjust the throttle cable play with barrel adjuster 3.

Guideline

Throttle cable play 3 … 5 mm (0.12 … 0.2 in)

–Tighten lock nut 2.

–Slide on sleeve 1.

3.5 Removing the passenger seat

Preparatory work

–Remove the front rider's seat. ( p. 9)

Andere Handbücher für RC 125

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere KTM Motorrad Handbücher

KTM

KTM 85 SX 2017 Handbuch

KTM

KTM 150 EXC TPI 2022 Bedienungsanleitung

KTM

KTM 65 SX 2017 Handbuch

KTM

KTM 50 SX 2017 Bedienungsanleitung

KTM

KTM 450 EXC-F Six Days 2017 Handbuch

KTM

KTM 85 SX 19/16 2013 Handbuch

KTM

KTM Freeride 250 R EU 2014 Handbuch

KTM

KTM Super Duke 990s Bedienungsanleitung

KTM

KTM 350 XCF-W USA Bedienungsanleitung

KTM

KTM 990 Super Duke EU 2010 Bedienungsanleitung

KTM

KTM 450 SMR Bedienungsanleitung

KTM

KTM 450 SX-F EU 2014 Handbuch

KTM

KTM Freeride 350 Bedienungsanleitung

KTM

KTM RC 390 2018 Bedienungsanleitung

KTM

KTM 1190 RC8 R EU/UK 2009 Bedienungsanleitung

KTM

KTM 50 SX 2015 Handbuch

KTM

KTM 250 EXC-F 2021 Bedienungsanleitung

KTM

KTM RC 125 EU 2015 Handbuch

KTM

KTM 350 EXC-F SIX DAYS EU Bedienungsanleitung

KTM

KTM RC 125 2018 Handbuch

KTM

KTM SX-E 5 Handbuch

KTM

KTM 125 SX 2021 Bedienungsanleitung

KTM

KTM 690 Enduro R 2021 Handbuch

KTM

KTM 85 SX 2018 Handbuch

Beliebte Motorrad Handbücher anderer Marken

OHVALE

OHVALE GP-0 Stücklistenhandbuch

Yamaha

Yamaha Star XV19CTSZ 2009 Bedienungsanleitung

HYOSUNG

HYOSUNG ST7 Bedienungsanleitung

Husqvarna

Husqvarna FC 250 2016 Bedienungsanleitung

Ducati

Ducati SCRAMBLER 800 Gebrauchsanweisung

MOTO GUZZI

MOTO GUZZI QUOTA 1100 ES Bedienungsanleitung

APRILIA

APRILIA ETV MILLE CAPONORD - PART1 02-2001 Bedienungsanleitung

Yamaha

Yamaha 2006 YZF-R1V Bedienungsanleitung

Fantic

Fantic Enduro 125 Bedienungsanleitung

Ducati

Ducati Supersport 750 desmodue Bedienungsanleitung

MV Agusta

MV Agusta 2008 F4 312RR 1078 Gebrauchsanweisung

Yamaha

Yamaha XVS650A Bedienungsanleitung

Yamaha

Yamaha YZF-R6T(C) Handbuch

Ducati

Ducati 748 monoposto strada Bedienungsanleitung

ATK

ATK 1988 250 Bedienungsanleitung

Excelsior-HENDERSON

Excelsior-HENDERSON 1999 HCX Bedienungsanleitung

Triumph

Triumph Thunderbird Bedienungsanleitung

Yamaha

Yamaha 2006 FJR1300A Bedienungsanleitung