Kunz AcrEase MR44BE Datenblatt

1/19

44”ROUGH CUT

W ITH ELECTRIC CLUTCH BLADE ENGAGEMENT

OWNER’S MANUAL

With Assembly Instructions

For Models: MR44BE

KUNZ ENGINEERING, INC. / MENDOTA, IL 61342 / PH (815) 539-6954

sfasdfdsf

SAFETY INTRODUCTION

Your safety, and the safety of others, is very important. To help you make informed

decisions about safety, we have provided operating procedures and other information on

labels and in this manual. This information alerts you to potential hazards that could hurt

you or others.

This safety alert symbol is used to indicate safety instructions. Follow these

instructions to avoid personal injury and/or property damage. Read and follow all

instructions in this manual and the included engine manual.

You will find important safety information in a variety of forms, including:

Safety Labels – on the mower.

Safety Messages – preceded by a safety alert symbol and one of three signal

words: DANGER, WARNING, or CAUTION.

These signal words mean:

DANGER:Indicates an imminently hazardous situation that, if not avoided, will result in

death or serious injury. This signal word is to be limited to the most extreme situations

typically for machine components which, for functional purposes, cannot be guarded.

WARNING: Indicates a potentially hazardous situation that, if not avoided, could result in

death or serious injury, and includes hazards that are exposed when guards are removed.

It may also be used to alert against unsafe practices.

CAUTION:Indicates a potentially hazardous situation that, if not avoided, may result in

minor or moderate injury. It may also be used to alert against unsafe practices.

This entire manual is filled with important safety information. Please read it

carefully.

IMPORTANT SAFETY INFORMATION

WARNING: Do not allow anyone to operate this equipment who has not fully read and

comprehended the safety manual and who has not been properly trained in the safe

operation of the equipment.

WARNING: Operator should be familiar with all functions of the unit.

DANGER:Keep hands, feet, hair and clothing away from moving parts.

WARNING: Remove all objects from the work area that might be picked up and thrown by

the blades.

WARNING: Do not mow when children and others are around.

WARNING: Keep all safety shields and deflectors in place during operation.

WARNING: Shut off the engine and allow the mower blades to come to a complete stop

before making any adjustments to the mower.

WARNING: Shut off engine before disconnecting the mower from the tow vehicle or

attempting to move the mower by hand.

WARNING: Never carry children or passengers.

WARNING: Do not allow children to operate this machine.

WARNING: Follow all safety precautions outlined by the manufacturer of the tow vehicle

being used to pull this product.

This entire manual is filled with important safety information. Please read it

carefully.

SAFETY SIGNS AND LOCATIONS

Clean or Replace Any Safety Signs That Are not Readable or Damaged

Replacement decals can be purchased from your local dealer or

Kunz Engineering Inc.

Mendota, IL 61342

(815) 539-6954

275003 – Danger

Decal, Cut Hand & Foot

275007 – Warning

Decal, Belt Sheild

275002 – Warning

Decal, General

Serial # and Model #

Decal

ASSEMBLY INSTRUCTIONS

Read the complete assembly instructions before starting the assembly.

You should have:

- one mower deck assembly

- two carrier arm assemblies

- two rear tire assemblies

- one front cross brace tube and one rear cross brace tube with height adjust assy.

- one ATV tongue assembly

A. ASSEMBLY OF REAR WHEELS AND CARRIER ARMS

1. Set the mower deck assembly on wood blocks so that it is suspended off the ground.

Note: The operator controls are on the front of the deck. (Left and right are determined by

looking in the direction of travel or by standing at the rear of the deck assembly looking

forward.)

2. Install the rear tire assemblies on the carrier arm assemblies. Remove the hex nut and lock

washer from the rear tire assembly and install the 5/8”x7-1/2” tire axle bolt through the hole in

the carrier arm assembly. See figure 1. Secure assembly with the lock washer and hex nut

provided on the rear tire assembly. The rear tires should be offset to the outside of the deck

assembly on both sides. See figure 2.

Figure 1: Rear Tire Assembly Installation

Flat Washer

Rear Tire

Carrier Arm

Assembly

Hex Nut and

Lock Washer

Cup Washer

Bolt

Spanner

Tube

3. Install the two carrier arm assemblies in the pivot arms, which are located on the mower deck

assembly. Place the assembly so that the castered tires are on the front and the fixed tires are

on the back. See figure 2. Secure with 1/2" x 3-1/2" hex head bolts and lock nuts provided on

the pivot arms.

Note: Tighten 1/2” x 3-1/2” hex head bolts until just snug. This area needs to pivot when

adjusting the height. Under tightening can result in excessive wear and flexing. Over

tightening will make adjusting the cutting height very difficult.

Figure 2: Carrier Arm Installation

B. INSTALLATION OF CROSS BRACE TUBES AND HEIGHT ADJUST ASSY.

For this section, if your mower was purchased with an Electric Lift Kit (Part #003912), refer to

Section C of the Electric Lift Kit Owner’s Manual.

1. Remove the 1/2” x 3” hex head bolts, lock washers and nuts that are located on the top of

each carrier arm (four per carrier arm). The removed hardware will be used in step 2.

2. Install the cross brace tubes on the carrier arms with the 1/2” x 3” hex head bolts, lock washers

and nuts. Only hand tighten the hardware for this step. The support that has the height adjust

assy. fastened to it needs to be placed on the rear location. Orientate the support such that

the height adjust assy. hangs towards the engine. See figure 3.

3. Remove the 1/2” x 1” bolt and lock nut from the lower deck mount. Manually turn the screw

down towards the deck until the screw mounting flat hole lines up with the lower deck mount

hole. After achieving alignment, attach the screw mounting flat with the 1/2” x 1” hex head bolt

and secure the bolt with the provided lock nut. Do not over-tighten. This location must be able

to pivot. See figure 4.

Rear Tire Assy.

(Attach on outside for

both left and right sides)

Pivot Arm

Front (Rubber

Flap Side)

Carrier Arm

Assy.

1/2” x 3-1/2” Bolt

Figure 3: Cross Brace Tube Installation

Figure 4: Height Adjust Assy. Installation

4. Turn the crank on the height adjust assy. and raise the mower to its highest position. At this

time securely tighten the 1/2” x 3” hex head bolts, lock washers and nuts holding the cross

brace tubes in place. This step insures that proper alignment of the carrier arms has been

achieved.

Height Adjust Assy.

Cross Brace

Tube

1/2” x 3” Bolt

Screw Mounting

Flat

Height Adjust

Assy.

1/2” x 1” Bolt

Lower Deck

Mount

Screw

C. INSTALLATION OF TONGUE ASSEMBLY

1. The tongue can be installed either on the left or right carrier arm assembly depending on how

the tow-behind mower will be towed. See figure 5.Secure the hitch pivot on the chosen

carrier arm assembly with the 1/2” x 3-1/2” hex head bolt, lock washer, and nut provided.

2. Install the tongue into the hitch pivot and secure by placing the provided 5/16” wire lock pins on

each side of the hitch pivot.

Note: To help prevent any unwanted pin removal caused by oncoming debris install the 5/16”

wire lock pins with the wire lock section back from the direction of travel. See Figure 6.

Figure 5: Assembly of the Tongue and Hitch Pivot

Hitch Pivot – Attach to

Either Left or Right

Carrier Arm Assy.

Tongue

Carrier Arm

Assy.

Direct Behind Position

Offset Position

Figure 6: ATV Tongue Assembly

OPERATIONS AND ADJUSTMENTS

This safety alert symbol is used to indicate safety instructions. Follow

these instructions to avoid personal injury and/or property damage.

Read and follow all instructions in this manual and the attached engine

manual.

WARNING: Do not allow anyone to operate this equipment who has not fully read and

comprehended the safety manual and who has not been properly trained in the safe

operation of the equipment.

WARNING: Operator should be familiar with all functions of the unit.

A. TONGUE CONFIGURATIONS AND ADJUSTMENTS

WARNING: Shut off the engine and allow the mower blades to come to a complete stop

before adjusting the tongue.

The hitching system is designed so that the rough cut mower can be pulled directly behind a tow

vehicle or offset to the left or right. See Figure 7.

Note: When pulling the mower directly behind, the hitch pivot should be fastened on the right

carrier arm for maximum maneuverability. See Figure 5. When pulling the mower in

the offset position the hitch pivot can be fastened on either the right or left carrier arm.

See Figure 5.

Wire Lock Section of

Wire Lock Pin

(Placed Back From

Direction of Travel)

5/16” Wire

Lock Pins

Direction of Travel

Screw Pin Shackle

Clevis

Tongue

Shift Tongue Left or Right

Between Holes

Inhaltsverzeichnis

Andere Kunz Rasenmäher Handbücher

Kunz

Kunz AcrEase MR44B Bedienungsanleitung

Kunz

Kunz AcrEase MR55KE Bedienungsanleitung

Kunz

Kunz AcrEase C60BE Bedienungsanleitung

Kunz

Kunz AcrEase MR55K Datenblatt

Kunz

Kunz AcrEase MR55B Bedienungsanleitung

Kunz

Kunz AcrEase Pro60K-25HP Bedienungsanleitung

Kunz

Kunz AcrEase MR55KEI Datenblatt

Kunz

Kunz AcrEase MR44B Datenblatt

Kunz

Kunz AcrEase MR55BE Datenblatt

Kunz

Kunz AcrEase MR55B Bedienungsanleitung

Kunz

Kunz AcrEase MR44V Bedienungsanleitung

Beliebte Rasenmäher Handbücher anderer Marken

RHINO

RHINO 1958 Bedienungsanleitung

Wolf Garten

Wolf Garten Compact plus 40 B Bedienungsanleitung

Cub Cadet

Cub Cadet LTX 1045 Bedienungsanleitung

Craftsman

Craftsman 917.378461 Bedienungsanleitung

GGP ITALY SPA

GGP ITALY SPA CR/CS 434 SERIES Bedienungsanleitung

Challenge

Challenge CH18V2 Betriebsanleitung

TALEN TOOLS

TALEN TOOLS AVR HGM30 Bedienungsanleitung

DEWEZE

DEWEZE ATM-725 Bedienungsanleitung

Weed Eater

Weed Eater 180083 Bedienungsanleitung

Husqvarna

Husqvarna Poulan Pro PP185A42 Bedienungsanleitung

Better Outdoor Products

Better Outdoor Products Quick Series Bedienungsanleitung

Cub Cadet

Cub Cadet 23HP Z-Force 60 Betriebsanleitung

MTD

MTD 795, 792, 791, 790 Bedienungsanleitung

Toro

Toro Groundsmaster 3505-D Bedienungsanleitung

Dennis

Dennis FT 610 Bedienungsanleitung

AIRFORCE

AIRFORCE F-15 Gen 3 Bedienungsanleitung

MTD

MTD 126-220-000 Bedienungsanleitung

Toro

Toro 74806 Bedienungsanleitung