Kustom KXB200H Bedienungsanleitung
Congratulations on the purchase of your new Kustom bass amplier.
Your KXB Model draws on decades of amp design and manufacturing
experience at Kustom. This model was built from the ground up to offer
world-class tone, useful features and reliable performance. Inside this manual,
you’ll nd valuable information about the amp’s controls and specications.
Being familiar with its features will help you effectively dial in different tones.
We wish you many years of enjoyment with your Kustom amplier.
OWNER’S MANUAL
kustom.com
KXB200H/HR BASS GUITAR AMPLIFIER
KXB200H
KXB200
KXB200
KXB200HR
FCC Statements
1. Caution: Changes or modications to this unit not expressly approved by the party
responsible for compliance could void the user’s authority to operate the equipment.
2. Note: This equipment has been tested and found to comply with the limits for a Class B
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
kustom.com
ENGLISH
kustom.com
FRENCH
1. 0 dB Input: ¼-inch input that is intended for bass guitars with standard, passive electronics.
2. –6 dB Input: ¼-inch input that is optimized for bass guitars with active electronics.
3. Gain: Controls the input level to the preamp. Set so Clip indicator light is not lit, otherwise distortion may occur.
4. Volume: Controls the overall volume level of the amplier. Use in conjunction with the Gain control to obtain the
desired level.
5. EQ-63: This active control adjusts the low frequencies to boost or cut by 12 dB centered at approximately 63 Hz.
6. EQ-150: This active control adjusts the low-mid frequencies to boost or cut by 12 dB centered at approximately 150
Hz.
7. EQ-350: This active control adjusts the low-mid frequencies to boost or cut by 12 dB centered at approximately 350
Hz.
8. EQ-800: This active control adjusts the hi-mid frequencies to boost or cut by 12 dB centered at approximately 800 Hz.
9. EQ-2K: This active control adjusts the high frequencies to boost or cut by 12 dB centered at approximately 2 kHz.
10. EQ-5K: This active control adjusts the high frequencies to boost or cut by 12 dB centered at approximately 5 kHz.
11. Aux In: This is a 3-conductor, 1/8-inch, stereo jack that allows playback from a Compact Disc, MP3 player or other
audio device. The overall volume level will be determined by the audio device, so start with lower volume levels and
increase as needed.
12. Headphones: This is a 3-conductor, 1/8-inch input jack intended for headphone use. The amplier’s internal speaker
is disconnected when this jack is used.
13. Power Switch: This dual-function component is both an On/Off power switch and a status indicator light. When
illuminated, it shows that your amplier is ready to be played. To turn amplier on, press switch upward. To turn amp off,
press switch downward.
1234678
kustom.com
5109 11 1312
KXB200
KXB200H/HR Control Panel
kustom.com
/
KXB200H HR
Speaker Outputs: These are two-conductor, ¼-inch external speaker jacks. These jacks are wired in a parallel
conguration. Use them to connect the amplier head to speaker cabinets with a minimum total impedance of 4 ohms.
(Note: Be sure that the amp is turned off before connecting or disconnecting speaker cabinets.)
Examples:
If you have two 8-ohm speaker cabinets and plug one into each of the amplier’s two speaker jacks, the total load will be
4 ohms. Because this is equal to the minimum-rated load for the amplier (4 ohms), this combination is acceptable.
If you have two 4-ohm speaker cabinets and plug one into each of the amplier’s two speaker jacks, the total load will
be 2 ohms. Because this is below the minimum-rated load of the amplier (4 ohms), this combination must not be
used.
Effects Loop Send: Use this 2-conductor, ¼-inch jack to connect to the input of an external effects processor or
equalizer. This jack can also be used as a Preamp Out.
Effects Loop Return: Use this 2-conductor, ¼-inch jack to connect to the output of an external effects processor or
equalizer. This jack can also be used as a Power Amp In.
Balanced Line Out: This XLR jack is used to connect the amplier to a mixer or other line level amplier. (Note: This
output is post-EQ and post- Effects Loop but is located before the Volume control.)
Direct Out Volume: This control sets the output level for the Balanced Line Out. Set in its lower ranges until necessary
volume has been determined.
Ground Lift: Activating this switch removes the ground connection on the Balanced Line Out jack. If necessary, use this
switch to eliminate hum.
KXB200H/HR Back Panel
kustom.com
KXB200H/HR AC Mains
KXB200H/HR Suggested Settings
The following suggested settings will help you dial in a variety of popular tones. Keep in mind, these are starting points to
get you up and running with your KXB amplier. Feel free to experiment to achieve your own signature sounds.
TRADITIONAL/VERSATILE TONE
In this setting, the amplier will deliver a traditional, yet versatile, electric bass sound. Whether you are playing Rock,
Country, Blues or Gospel, this setting will get you close. If you play with a pick and want less treble attack on the notes,
decrease the amount of high frequencies using the 2K and 5K controls. If you need a deeper bottom end, increase the
amount of low frequencies using the 63 control. Adjust the amount of Low and High Midrange to best match the tone of
your bass guitar and how it ts into the overall sound.
FUNKY, SLAPPED TONES
This style of music needs a strong attack with lots of treble. Using less Low-mids will help produce the extra top end
necessary for this type of music. If you use a “slapping” thumb technique, add a bit more low end and extra volume –
or less if you really hit the strings hard.
ALTERNATIVE STYLE
These settings are designed for upper-end punch and edge that will cut through most any sound mix. This tone will
work well with pick or ngers. Make sure your bass guitar’s volume control is turned up all the way. Since you’re adding
volume, be careful with the amount of EQ that you dial in, as it can also add some distortion to the sound.
kustom.com
KXB200
KXB200
KXB200
Kustom® KXB200H/HR Specications
Output Power 200 Watts 4 Ohms at 5% THD+N
Input Impedance Dual Input 0 dB: 500K Ohm, -6dB: 95K Ohm
Gain 75 dB Gain and Master at Max, All EQ at 12 o’clock
S/N Ratio -80 dB typical Below rated power
DIrect Output Electronically Balanced
XLR
Ground Lift Switch and Level control
Aux Input 800 mV Sensitivity Stereo 3.5mm High Impedance
Headphone Output 15 mW @ 30 ohms
per channel
Stereo 3.5mm, 8 ohm minimum
Effects Loop 800 mV/1K Ohm output
impedance
Effects Send, Gain and Master at 12
o’clock
800 mV/22K Ohm output
impedance
Effects Return, Gain and Master at 12
o’clock
Amplier Tone Controls 63 Hz +/- 12 dB
150 Hz +/- 12 dB
350 Hz +/- 12 dB
800 Hz +/- 12 dB
2 KHz +/- 12 dB
5 KHz +/- 12 dB
Power Requirements USA/Canada 120VAC/60Hz, 300W
Europe 230VAC/50Hz, 300W
UK 240VAC/50Hz, 300W
Australia 240VAC/50Hz, 300W
Japan 100VAC/50-60Hz, 300W
Dimensions/Weight
Head
cm3/Kilogram 24.4 (Height) X 50.8 (Width) X 27.9 (Depth),
12.5 Kilogram
Inches/Pounds 9.6 (Height) X 20 (Width) X 11 (Depth),
27.6 Lbs
Dimensions/Weight
Rack Mount
cm3/Kilogram 8.9 (Height) X 43.2 (Width) X 24.4 (Depth),
6.5 Kilogram
Inches/Pounds 3.5 (Height) X 17 (Width) X 9.6 (Depth),
14.3 Lbs
kustom.com
kustom.com
KXB200H/HR Signal Flow Diagram
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Kustom Verstärker Handbücher
Kustom
Kustom 36 coupe Bedienungsanleitung
Kustom
Kustom KDA100 Bedienungsanleitung
Kustom
Kustom DE200HD Bedienungsanleitung
Kustom
Kustom KGA10FX Bedienungsanleitung
Kustom
Kustom Dart 10FX Bedienungsanleitung
Kustom
Kustom KXB20 Bedienungsanleitung
Kustom
Kustom 12 Gauge Bedienungsanleitung
Kustom
Kustom 16 Bedienungsanleitung
Kustom
Kustom KPM4080 Bedienungsanleitung
Kustom
Kustom Quad 100 HEAD Bedienungsanleitung
Kustom
Kustom Defender V50 Bedienungsanleitung
Kustom
Kustom DOUBLE BARREL Bedienungsanleitung
Kustom
Kustom GROOVE 215H Bedienungsanleitung
Kustom
Kustom Dual 30 RC Bedienungsanleitung
Kustom
Kustom Arrow 16DFX Bedienungsanleitung
Kustom
Kustom GROOVE 1300 Bedienungsanleitung
Kustom
Kustom KBA 30X Bedienungsanleitung
Kustom
Kustom KHS-6640 Bedienungsanleitung
Kustom
Kustom KBA35XDFX Bedienungsanleitung
Kustom
Kustom KXB200 Bedienungsanleitung
