Kutai electronics ADVR-054 Bedienungsanleitung
KUTAI ELECTRONICS INDUSTRY CO., LTD.
TEL : +886-7-8121771 FAX : +886-7-8121775 Website : www.kutai.com.tw
Headquarters : No.3, Ln. 201, Qianfu St., Qianzhen Dist., Kaohsiung City 80664, Taiwan
ADVR-054
Universal Hybrid Analog-Digital
Voltage Regulator Operation Manual
Self Excited 5 Amp Analog / Digital Voltage Regulator
For shunt and auxiliary windings generators
With over-excitation and lost of sensing protection
Use with Kutai EP200 Paralleling Module for parallel operation
___________________________________________________________________________________________
2ADVR-054
WARNING
1. Some generators even when working at high voltage are factory set to sense at lower voltages.
Remember to set the DIP SW 2 to the sensing voltage not the working voltage of the generator even do
sometimes it can be the same. If you have a 480/277V generator but you have the sensing wires C and A
connected to 240 Volts move DIP SW 2 to ON
Another example are rental units with multi-voltage output with a switches for Y, YY, Delta & ZZ output,
but sensing is always at 240V from T7 and T9 even though the generator is running sometimes at
480/277V.
2. All voltage readings are to be taken with an average-reading voltmeter Meggers and high-potential test
equipment must not be used. Use of such equipment could damage the AVR.
3. Improper setting of under-frequency protection could cause the output voltage of the unit to drop or
become unstable under with changes in load. Avoid making any changes to the U/F setting unless
necessary.
SECTION 1 : SPECIFICATION
Sensing Input (A, C) Average Reading
Static Power Dissipation
Voltage 170 260Vac@220Vac,1phase2wires
Max.8 watts
340 520Vac@440Vac,1phase2wires
220/440 Vac, DIP switch setting
Under Frequency Protection (Factory Presets)
Frequency 50/60 Hz, DIP switch setting
50 Hz system presets knee point at 45 Hz
60 Hz system presets knee point at 55 Hz
Power Input (B, C)
Voltage 100 300 Vac, 1 phase 2 wires
Over Excitation Voltage Protection
Frequency 40 60 Hz
Set point 78 Vdc +/- 6% @ power input 220 Vac
Time delay 5 secs. This function can be turned off.
Excitation Output (F+, F-)
220V 1 phase Continuous 63 Vdc 5A
Voltage Thermal Drift
Max. 90 Vdc 7A for 10 secs.
Less than 3% at temperature range -40 to +70 ˚C
Resistance Min. 15 ohms, Max. 100 ohms
Fuse Spec. Slow blow 5 x 20mm S505-5A
Under-Frequency Knee Point Thermal Drift
Less than +/- 0.1 Hz at -40 to +70 ˚C
External Voltage Adjustment (EXT.VR)
Max. +/- 3.5% @ 1K ohm 1 watt potentiometer
Environment
Operating Temperature -40 to +60 ˚C
Voltage Regulation
Storage Temperature -40 to +85 ˚C
Less than +/- 0.5% ( with 4% engine governing )
Relative Humidity Max. 95%
Vibration 5 Gs @ 60 Hz
Build Up Voltage
5 Vac 25 Hz residual volts at power input terminal
Dimensions
121.0 (L) x 81.0 (W) x 44.5 (H) mm
Soft Start Ramp Time
4.76 (L) x 3.19 (W) x 1.75 (H) inch
3 seconds +/- 10%
Weight
Typical System Response
270 g +/- 2%
Less than 20 milliseconds
0.6 lb +/- 2%
EMI Suppression
Internal electromagnetic interference filtering
___________________________________________________________________________________________
ADVR-0543
SECTION 2 : APPEARANCE / DIMENSIONS / INSTALLATION DRAWING
M4 L25
8.5
[1.96"]
27.0
44.5
50.0
[1.75"]
[1.06"]
[0.33"]
Unit : mm
[inch]
ATTENTION
1. Only qualified technicians should install and operate the AVR.
2. The voltage regulator may be installed at any suitable location on the generator set (dimensions are
shown in Figure 1). It is recommended that unit is mounted vertically with the green resistors on the
regulator upwards to achieve the best cooling effect.
3. All AC voltage sensing readings are average value only.
Figure 1 Outline Drawing
___________________________________________________________________________________________
4ADVR-054
SECTION 3 : DIP SWITCH SETTINGS, LED INDICATORS AND ADJUSTMENTS
VOLT Voltage Adjustment
The adjustment range is set by
SW2.
U/F Under Frequency Protection
50 Hz system preset at 45 Hz,
60 Hz system preset at 55 Hz,
To change the setting, see the
Adjustment Step 3.
U/F LED
Under Frequency Protection status.
A：Sensing Input terminal
A to C: 170 –520 Vac
F+ , F-：Connect to generator
excitation field.
B：Power Input terminal
B to C: always less than 300 Vac
C：SensingInputandPowerInputterminals
EXT.VR Ext Potentiometer,
1K ohm 1W. Keep shorted when
not in use.
ADJUSTMENTS AFTER GENERATOR IS STARTED :
1. First, turn VOLT and STAB trimpots fully counterclockwise before starting the generator. Set the engine
governor to 50 or 60 Hz. Start the generator and wait till it reaches rated speed. Now slowly turn VOLT trimpot
clockwise to increase the working voltage. (If you use an external potentiometer, set it to the center position).
Keep EXT. VR shorted when not in use.
2. Next, slowly adjusting the STAB trimpot etting (clockwise), this change the response time of the AVR to
changing loads. If the setting is too high the voltage is unstable but if set too low the response is sluggish. We
recommend using an analog DC voltage meter on F, F+ and adjust STAB for the lowest amount of voltage
fluctuation (needle movement).
3. Last, Under Frequency (U/F) adjustment. (The U/F is Factory preset and needs no adjustments) put in rare
applications. Use the U/F LED as a guide. When this LED is ON the circuit is operational turning off the
regulators output. To recalibrate, adjust the generator speed to the new U/F kneel point, usually 5 Hz under
rated speed (Hz) then set the U/F trim-pot to the point at which the U/F LED just changes from off to on rated
speed (Hz) then set the U/F trimpot to the point at which the U/F LED just changes from off to on. Adjustment
range for 50Hz system is 40 to 51 Hz. For 60 Hz system the range is 50 to 61 Hz.
Over Excitation (O/E) LED
When the excitation voltage is greater than 35%
of input power voltage, the LED will lit after 5
sec. If the DIP switch SW3 set at OFF then it will
also shut off excitation output at the same time.
DIP Switches
System Freqency SW1 ON:50 Hz, OFF:60 Hz
Sensing Input SW2 ON:220V, OFF:440V
O/E Protection SW3 ON:Disable, OFF:Enable
STAB Stability Setting
With No Load, slowly turn the
STAB counterclockwise until
voltage becomes unstable then
turn clockwise about 1/5 turn.
-+
S F
40 51
(50) (61)
ADVR-054
___________________________________________________________________________________________
ADVR-0545
SECTION 4 : CONNECTION DIAGRAMS
ADVR-054
1000 Ohm
EXT. VR
~
G
Field
R
S
N
T
1000 Ohm
EXT. VR
~
G
Field
R
S
N
T
ADVR-054
Figure 3 170 260V sensing connection (Option 1)
Figure 4 170 260V sensing connection (Option 2)
1000 Ohm
EXT. VR
~
G
R
S
N
T
Field
ADVR-054
Aux.winding 1000 Ohm
EXT. VR
~
G
Field
R
S
N
T
ADVR-054
Figure 5 340 520V sensing connection
Figure 6 Auxiliary Winding connection
※Package include 4 pcs of M4 L25 Round head bolts and 2 pcs of terminal jumpers.
※Use only replacement fuses specified in this user manual.
※Appearance and specifications of products are subject to change for improvement without prior notice.
Refer to Section 3
for DIP Switch
setting.
Refer to Section 3
for DIP Switch
setting.
Refer to Section 3
for DIP Switch
setting.
Refer to Section 3
for DIP Switch
setting.
Inhaltsverzeichnis
Andere Kutai electronics Controller Handbücher
Kutai electronics
Kutai electronics ADVR-16 Bedienungsanleitung
Kutai electronics
Kutai electronics ADVR-073 Bedienungsanleitung
Kutai electronics
Kutai electronics EA230 Bedienungsanleitung
Kutai electronics
Kutai electronics EA63-2.5 Bedienungsanleitung
Kutai electronics
Kutai electronics EA45A220 Series Bedienungsanleitung
Kutai electronics
Kutai electronics ADVR-12 Bedienungsanleitung
Kutai electronics
Kutai electronics EA06 Bedienungsanleitung
Kutai electronics
Kutai electronics ADVR-083 Bedienungsanleitung
Kutai electronics
Kutai electronics ADVR-250 Bedienungsanleitung
Kutai electronics
Kutai electronics EG3002 Bedienungsanleitung
Kutai electronics
Kutai electronics EA04C Bedienungsanleitung
Kutai electronics
Kutai electronics EA440 Bedienungsanleitung
Kutai electronics
Kutai electronics ADVR-2300M Bedienungsanleitung
Kutai electronics
Kutai electronics ADVR-083-400HZ Bedienungsanleitung
Kutai electronics
Kutai electronics EA05A Bedienungsanleitung
Kutai electronics
Kutai electronics ADVR-053 Bedienungsanleitung
Kutai electronics
Kutai electronics EA125-8 Bedienungsanleitung
Kutai electronics
Kutai electronics EA350 Bedienungsanleitung
Kutai electronics
Kutai electronics ADVR-073 Bedienungsanleitung
Kutai electronics
Kutai electronics ADVR-2200M Bedienungsanleitung
