Kutai electronics ADVR-083-400HZ Bedienungsanleitung
KUTAI ELECTRONICS INDUSTRY CO., LTD.
TEL : +886-7-8121771 FAX : +886-7-8121775 Website : www.kutai.com.tw
Headquarters : No.3, Ln. 201, Qianfu St., Qianzhen Dist., Kaohsiung City 806037, Taiwan
ADVR-083-400HZ
Universal Hybrid Analog-Digital
Voltage Regulator Operation Manual
Universal 400Hz Intermediate Frequency
Analog / Digital AVR, Single-phase / Three-phase Sensing
8 Amp Voltage Regulator for use with Auxiliary Winding, PMG, and
self-excited (SHUNT) brushless generators.
For Aviation and Military Spec 400Hz Generators
___________________________________________________________________________________________
2ADVR-083-400HZ
SECTION 1 : SPECIFICATION
Sensing Input (E1, E2, E3) Average Reading
Soft Start Ramp Time
Voltage and Frequency DIP switch settings
4 seconds +/- 10%
1 phase (E1, E2) / 3 phase (E1, E2, E3)
90 130 Vac @ 110 Vac
Voltage Regulation
180 260 Vac @ 220 Vac
Less than +/- 0.5% (with 4% engine governing)
340 520 Vac @ 440 Vac
Frequency 320 420 Hz
Typical System Response
Less than 20 milliseconds
Power Input (X1, X2, Z2)
Voltage 60 300 Vac, 1 phase / 3 phase
EMI
1 phase ( X1, X2 ) / 3 phase ( X1, X2, Z2 )
Built-in Harmonic suppression
Frequency 40 500 Hz
Static Power Dissipation
Auxiliary Input (Z1, Z2)
Max. 6 watts
Voltage 60 300 Vac, 1 phase 2 wire
Frequency 40 500 Hz
Under Frequency Protection (Factory Preset)
400 Hz system preset knee point at 360 Hz
Excitation Output (F+, F-)
110V 1 phase Continuous 63 Vdc 8A
Over Excitation Protection
Max. 90 Vdc 10A for 10 secs.
25 105% of Input Power (adjust with OE pot.)
220V 1 phase Continuous 125 Vdc 8A
O/E acts after 10 sec. delay. The OE function can be
Max. 180 Vdc 10A for 10 secs.
turned OFF by adjusting OE. clockwise to max.
220V 3 phase Continuous 150 Vdc 8A
Max. 215 Vdc 10A for 10 secs.
Voltage Thermal Drift
Resistance Min.15 ohms, Max.100 ohms @ 220V
Less than 3% from -40 to +70 ˚C
Fuse Spec. Slow blow 5 x 20 mm 10A
Under-Frequency Knee Point Thermal Drift
External Voltage Adjustment (VR1, VR2)
Less than +/- 0.1 Hz from -40 to +70 ˚C
Max. +/- 10% @ 1K ohm 1 watt potentiometer
Environment
Quadrature Droop Input (S1, S2)
Operation Temperature -40 to +60 ˚C
CT N:5A or N:1A (DIP switch setting)
Storage Temperature -40 to +85 ˚C
Burden : greater than 5VA
Relative Humidity Max. 95%
Sensitivity +/- 7% @ PF +/- 0.5
Vibration 5.5Gs @ 60 Hz
(Can be adjusted through Droop setting)
Dimensions
Analogue Voltage Input (A1, A2)
150.0 (L) x 135.0 (W) x 61.0 (H) mm
Input resistance greater than 2K ohms
5.91 (L) x 5.31 (W) x 2.40 (H) inch
Input Range +/- 5 Vdc or 0 10 Vdc
Sensitivity Max.1 Vdc = 5% change in output voltage
Weight
(Can be adjusted through Trim setting)
750 g +/- 2%
1.654 lb +/- 2%
Build Up Voltage
Greater than 5 Vac, 25 Hz residual volts input power
ATTENTION
In order to avoid permanent damage to the AVR confirm that the voltage sensing input setting matches
the generator before use (DIP switches SW5 and SW6)
___________________________________________________________________________________________
ADVR-083-400HZ 3
SECTION 2 : OUTLINE / SIZE / INSTALLATION REFERENCE
130.0 [5.12"]
150.0 [5.91"]
21.5 [0.85"]
61.0 [2.40"]
135.0 [5.31"]
115.0 [4.53"]
5.5 [0.22"]
Figure 1 Outline Drawing
___________________________________________________________________________________________
4ADVR-083-400HZ
SECTION 3 : DIP SWITCH PROGRAMMING & VR ADJUSTMENTS
VOLT：Voltage Adjustment
Sensing input voltage range set by DIP
switches SW5 and SW6
X1, X2：Single Phase Power Input
Z1, Z2：Auxiliary Power Input
X1, X2, Z2：Three Phase Power Input
Remark : X1 and Z1 are the same point
(internally shorted)
S1, S2：Quadrature Droop Input
Sensitivity +/- 7% @ PF +/- 0.5
CT N : 5A or N : 1A set by DIP
switches SW3
VR1, VR2：External VR Input
Must be shorted when not in use
A1, A2：Analog Voltage Input
Max. Input +/- 5 Vdc or 0 –10 Vdc
DROOP：DROOP Adjustment
(Parallel operation)
Droop Adjustment
Used only during parallel operation
F+, F-：Excitation Output
Connects to generator excitation field
E1, E2：Single Phase Sensing Input
E1, E2, E3：Three Phase Sensing Input
Single Phase / Three Phase sensing set by DIP
switch SW7
OE.：Over Excitation Protection Adjustment
25 105% of Rated Excitation (Adjustable)
Adjust OE. potentiometer clockwise to Max.
to turn OFF O/E protection
STAB：Stability Adjustment
Stability range set by DIP
switches SW1 and SW2
U/F：Under-Frequency LED
Under-Frequency Protection status
(ON = Activated)
DIP：U/F Protection Voltage Slope
Adjustment
When U/F protection is activated the voltage
drop ratio can be adjusted by DIP switch.
Adjustment range 3 to 6 V/Hz
UF：UnderFrequencyAdjustment
Under frequency knee point setting
400 Hz system：320 to 400 Hz adjustable
O/E：Over Excitation LED
Over Excitation Protection status
(ON = Activated) Excitation Output
will be reduced after a 10 sec delay
TRIM：Analogue Voltage Input Adjustment
Max. Input +/- 5 Vdc or + 10 Vdc
Sensitivity 1 Vdc for 5% (adjustable)
ADVR-083-400HZ
ON
OFF
SW
3
CT 5A
CT 1A
4
400 Hz
7
1£X SENSING
3£X SENSING
1. OFF
2. OFF
<90KW
1. OFF
2. ON
90-500KW
1. ON
2. ON
>500KW
5. OFF
6. OFF
110V
5. ON
6. OFF
220V
5. OFF
6. ON
440V
5140 (61)(50)
F S
___________________________________________________________________________________________
ADVR-083-400HZ 5
SECTION 4 : WIRING CONNECTIONS
Dotted lines represent a three-phase input. Do not connect if installed in single-phase system
ADVR-083-400Hz
~
G
R
S
N
T
Field
potentiometer
1k /1W
External
ADVR-083-400Hz
~
G
R
S
N
T
Field
potentiometer
1k /1W
External
Figure 3 Self-Excited (SHUNT) 110/220 Vac
Single phase / Three phase
Figure 4 Self-Excited (SHUNT) 380/440 Vac
Single phase / Three phase
ADVR-083-400Hz
~
G
R
S
N
T
Field
AUX. wires
potentiometer
1k /1W
External
Figure 5 Auxiliary Winding 110/220/440 Vac
Single phase / Three phase
ATTENTION
1. Before using a Megger or a Withstand Voltage Tester remove the wires connecting to the AVR to
prevent high voltage damage to the regulator.
2. Improper setting of under-frequency protection could cause the output voltage of the unit to drop or
become unstable under with changes in load. Avoid making any changes to the U/F setting unless
necessary.
3. Turn off O/E in AVR when paralleling.
※Use only the replacement fuses specified in this user manual.
※Appearance and specifications of products are subject to change for improvement without prior notice.
ADVR-083-400HZ
ADVR-083-400HZ
ADVR-083-400HZ
Inhaltsverzeichnis
Andere Kutai electronics Controller Handbücher
Kutai electronics
Kutai electronics EG3002 Bedienungsanleitung
Kutai electronics
Kutai electronics EA45A220 Series Bedienungsanleitung
Kutai electronics
Kutai electronics ADVR-083 Bedienungsanleitung
Kutai electronics
Kutai electronics EA440 Bedienungsanleitung
Kutai electronics
Kutai electronics EA63-2.5 Bedienungsanleitung
Kutai electronics
Kutai electronics EA42-7 Bedienungsanleitung
Kutai electronics
Kutai electronics EA230 Bedienungsanleitung
Kutai electronics
Kutai electronics EA125-8 Bedienungsanleitung
Kutai electronics
Kutai electronics ADVR-073 Bedienungsanleitung
Kutai electronics
Kutai electronics ADVR-2200M Bedienungsanleitung
Kutai electronics
Kutai electronics EA321 Bedienungsanleitung
Kutai electronics
Kutai electronics ADVR-053 Bedienungsanleitung
Kutai electronics
Kutai electronics EA05A Bedienungsanleitung
Kutai electronics
Kutai electronics ADVR-2300M Bedienungsanleitung
Kutai electronics
Kutai electronics ADVR-16 Bedienungsanleitung
Kutai electronics
Kutai electronics ADVR-250 Bedienungsanleitung
Kutai electronics
Kutai electronics EB-9V Bedienungsanleitung
Kutai electronics
Kutai electronics EA04C Bedienungsanleitung
Kutai electronics
Kutai electronics EA200A Bedienungsanleitung
Kutai electronics
Kutai electronics EA05A Bedienungsanleitung
