KVH Industries TracVision M7 Leitfaden

TracVision M7

RF PCB Replacement Instructions

TracVision®M7 RF PCB Replacement

Instructions

The following instructions explain how to replace the RF PCB in a

TracVision M7.

Tools Required

TIP: The Flash Update Wizard is available to KVH-authorized

dealers through the KVH Partner Portal at www.kvh.com/

partners.

• #1 Phillips screwdriver

• #2 Phillips screwdriver

• 3/8" nut driver or wrench

• 7/16" open-end wrench

CAUTION

For your own safety, be sure to disconnect power from all wired

components before performing this procedure.

54-0478 Rev. B

TracVision M7

RF PCB Replacement Instructions

Step 1 - Replace the RF PCB

a. Using a #2 Phillips screwdriver, remove the six #10-32

screws securing the radome. Then remove the radome

and set it aside in a safe place.

Figure 1 Radome Removal/PCB Cover Screws

b. Using a #1 Phillips screwdriver, remove the four screws

securing the PCB cover at locations 1-4 (see Figure 1).

Using a 3/8" nut driver or wrench, remove the three

nuts and washers at locations 5-7.

c. Carefully position the cover to allow access to the PCB.

NOTE: Be sure to handle the cover carefully to avoid damaging or

dislodging PCB components.

NOTE: The PCB module is static-sensitive. Ensure that you take the

necessary grounding precautions before handling.

PCB Cover

Radome

Baseplate

1234

Inverter PCB

(not present on all systems

)

TracVision M7

RF PCB Replacement Instructions

d. Label the two RF cables as shown in Figure 2. Then,

using a 7/16" open-end wrench, disconnect the two RF

cables from the RF PCB.

Figure 2 RF PCB Connections/Screws

e. Disconnect the two Molex wires from the main PCB.

f. Using a #1 Phillips screwdriver, remove the four screws

securing the RF PCB (see Figure 2).

g. Remove the faulty RF PCB.

h. Reverse this process to install the replacement RF PCB.

Then reinstall the radome and reconnect power to the

TracVision system.

Step 2 - Check the Main PCB Software Version

You might need to update the software in the TracVision system’s

main PCB, depending on its software version. The following

instructions explain how to check the currently installed main PCB

software version.

a. Follow the instructions provided in the TracVision M7

User’s Guide to connect a PC to the TracVision system.

b. Double-click the KVH Flash Update Wizard shortcut on

your PC’s desktop to start the Flash Update Wizard.

c. Type HALT then press Enter.

Connectors

Molex

Connectors

To IRD To LNB

= Screws (x4)

TracVision M7

RF PCB Replacement Instructions

d. Type VERSION then press Enter. The antenna’s main

PCB software version will appear in the “TracVision

Antenna Comms” window. Be sure to record the

software version for later use.

e. Type ZAP then press Enter.

f. Click the Flash Update Wizard’s “View Release Notes”

button. Then click the “Flash File Log” link within the

Release Notes. Ensure that your main PCB software

version matches the version listed for your TracVision

model.

g. If your software version matches the software version

listed in the Release Notes, the procedure is complete!

Be sure to return the old RF PCB to KVH.

NOTE: Before returning the RF PCB, be sure to obtain an RMA

number from KVH Technical Support and write the number clearly

on the outside of the box. Shipments received without an RMA

number will be returned to you at your expense.

If your software version does not match the software version

listed in the Release Notes, proceed to “Step 3 - Flash the

Main PCB (if required).”

Step 3 - Flash the Main PCB (if required)

The main PCB now needs to be updated, or “flashed” to ensure

compatibility with the new RF PCB. Flashing also allows the antenna

to use the most current satellite configuration data available. Follow

the Flash Update Wizard instructions to flash the main board only.

NOTE: Only flash the main PCB if your software version does not match the

software version listed in the Release Notes (see “Step 2 - Check the Main

PCB Software Version” on page 3).

The procedure is complete! Be sure to return the faulty RF PCB to

KVH.

NOTE: Before returning the RF PCB, be sure to obtain an RMA number

from KVH Technical Support and write the number clearly on the outside of

the box. Shipments received without an RMA number will be returned to you

at your expense.

Andere Handbücher für TracVision M7

Inhaltsverzeichnis

Andere KVH Industries Antenne Handbücher

KVH Industries

KVH Industries TracPhone V11 Bedienungsanleitung

KVH Industries

KVH Industries Ka Tri-Americas LNB Bedienungsanleitung

KVH Industries

KVH Industries TracPhone V11IP Bedienungsanleitung

KVH Industries

KVH Industries TracPhone V11IP Bedienungsanleitung

KVH Industries

KVH Industries TracVision R6 DX Leitfaden

KVH Industries

KVH Industries TracPhone V3 Leitfaden

KVH Industries

KVH Industries TracPhone V11 Bedienungsanleitung

KVH Industries

KVH Industries TracVision L3 Bedienungsanleitung

KVH Industries

KVH Industries TracNet H30 Bedienungsanleitung

KVH Industries

KVH Industries TracVision R6 DX Bedienungsanleitung

KVH Industries

KVH Industries TracPhone V11 hts Bedienungsanleitung

KVH Industries

KVH Industries TracPhone V7 Bedienungsanleitung

KVH Industries

KVH Industries TracVision M5 Bedienungsanleitung

KVH Industries

KVH Industries TracVision M5 Bedienungsanleitung

KVH Industries

KVH Industries TracPhone V3HTS Bedienungsanleitung

KVH Industries

KVH Industries 5616 Bedienungsanleitung

KVH Industries

KVH Industries TracPhone V11 hts Bedienungsanleitung

KVH Industries

KVH Industries TracPhone V3HTS Bedienungsanleitung

KVH Industries

KVH Industries TracPhone F55 Bedienungsanleitung

KVH Industries

KVH Industries TracPhone V30 Montage- und Bedienungsanleitung

KVH Industries

KVH Industries TracVision M7 Leitfaden

KVH Industries

KVH Industries tracvision M7SK Bedienungsanleitung

KVH Industries

KVH Industries TracPhone V3 Bedienungsanleitung

KVH Industries

KVH Industries TracVision 6 Bedienungsanleitung

Beliebte Antenne Handbücher anderer Marken

Alfa Network

Alfa Network APA-L01 Bedienungsanleitung

Naval

Naval PR-422CA Bedienungsanleitung

Feig Electronic

Feig Electronic ID ISC.ANTH200/200 Series Bedienungsanleitung

TERK Technologies

TERK Technologies TV44 Bedienungsanleitung

Directive Systems & Engineering

Directive Systems & Engineering DSE2324LYRMK Bedienungsanleitung

HP J8999A Bedienungsanleitung

MobilSat

MobilSat MSP-S Bedienungsanleitung

Steren

Steren ANT-UHF 13 Bedienungsanleitung

Novatel

Novatel 600-G Bedienungsanleitung

Radio Shack

Radio Shack Amplified VHF/UHF/FM Indoor Antenna Bedienungsanleitung

TRENDnet

TRENDnet TEW-AO12O Bedienungsanleitung

Radio Shack

Radio Shack 15-1837 Bedienungsanleitung

CommScope

CommScope CMAX-OMFX-43M-I53 Bedienungsanleitung

Ramsey Electronics

Ramsey Electronics DAP25 Bedienungsanleitung

COBHAM

COBHAM SAILOR 800 VSAT Gebrauchs- und Pflegehandbuch

Trango Systems

Trango Systems AD900-9 Bedienungsanleitung

Steren

Steren ANT-100 Bedienungsanleitung

Proxim

Proxim 5054-PA-23 Bedienungsanleitung