Kyocera Mita Ecosys FS-1000+ Bedienungsanleitung

Page Printer

Installation Manual

Caution

NO LIABILITY IS ASSUMED FOR ANY DAMAGE CAUSED BY IMPROPER INSTALLATION.

Notice on Software

SOFTWARE USED WITH THIS PRINTER MUST SUPPORT THE PRINTER'S EMULATION

MODE. The printer is factory-set to emulate the HP PCL 6. The emulation mode can be changed by

following the procedures described in the User's Manual contained as an electronic file in the

Kyocera Mita Digital Library CD-ROM supplied with the printer.

Notice

The information in this manual is subject to change without notification. Additional pages may be

inserted in future editions. The user is asked to excuse any technical inaccuracies or typographical

errors in the present edition.

No responsibility is assumed if accidents occur while the user is following the instructions in this

manual. No responsibility is assumed for defects in the printer's firmware (contents of its read-only

memory).

This manual, any copyrightable subject matter sold or provided with or in connection with the sale

of the page printer, are protected by copyright. All rights are reserved. Copying or other reproduc-

tion of all or part of this manual, any copyrightable subject matter without the prior written consent

of Kyocera Corporation is prohibited. Any copies made of all or part of this manual, any copyright-

able subject must contain the same copyright notice as the material from which the copying is done.

Table of Contents

STEP1 Unpacking.........................................................................1

STEP2 Positioning the Printer .....................................................2

STEP3 Installing the Toner Container .........................................3

STEP4 Connecting the Printer to the Computer.........................6

STEP5 Connecting the Power Cord ............................................8

STEP6 Adding Paper to the Paper Cassette and MP Tray .........9

STEP7 Using the Face-Up Output Tray .....................................14

STEP8 Printing a Status Page....................................................15

Ifs10ep-jp.book Page 1 Friday, December 22, 2000 4:27 PM

Go to next page

☞

Unpacking

Carefully remove the printer and other items from the box. Check that nothing is miss-

ing against the list of shipped components below.

Shipped Components

Removing Shipping Material

Remove the tape on the rear side of the printer, and remove the two spacers and

printed notice from the paper cassette.

STEP

Printer

Power Cord

Toner Container (TK-17)

Installation Manual (this booklet) Kyocera Mita Digital Library CD-ROM

Cleaning Cloth

Ta p e Spacers

Printed Notice

Ifs10ep-jp.book Page 1 Friday, December 22, 2000 4:27 PM

Positioning the Printer

Make sure that the place of installation meets the following requirements:

Clearance

Be sure to secure enough space

around the printer. Prolonged

use without sufficient clearance

may cause heat to build up

within the printer, resulting in

fire.

Environment

Do not install the printer where temperature or humidity is outside the rec-

ommended range. Print quality may suffer and there will be an increased

chance of paper jams.

Places to Avoid

Avoid installing the printer in locations subject to:

• Direct drafts of hot or cold air

• Direct drafts from outside (Avoid locations near building entrances.)

• Sudden temperature or humidity changes

• Sources of high temperature, for example, near stoves or radiators

•Excessivedust

•Vibration

• Unstable surfaces and surfaces that are not level

• Ammonia or other harmful fumes (If you are planning to fumigate the room, or

make liberal use of insecticide, remove the printer first!)

• Excessive sunlight or humidity

• Lack of ventilation

• Low air pressure, e.g., elevations greater than 2000 meters (6500 feet) above sea

level

Temperature 10 to 32.5 °C (50 to 90.5 °F), ideally about 23 °C (73.4 °F)

Humidity 20 to 80 %, ideally 60 %

STEP

30 cm (11-13/16 inches)

40 cm

(15-3/4

inches)

25 cm

(9-7/8

inches)

50 cm

(19-11/16

inches)

25 cm (9-7/8

inches)

Ifs10ep-jp.book Page 2 Friday, December 22, 2000 4:27 PM

Go to next page

☞

Installing the Toner Container

Before you can use the printer for the first time, you must set up the printer by installing

the toner container and interfacing with the computer.

1Open the printer top cover all the way.

2Confirm that the lock lever is in the

release (UNLOCK) position. If not, pull it

forward until it is in the release posi-

tion.

3Take the toner container from the bag.

Hold it with the protective seal (orange-

colored) facing up. Shake the toner con-

tainer horizontally at least 5 times. This

ensures that the toner is evenly distrib-

uted inside.

STEP

Ifs10ep-jp.book Page 3 Friday, December 22, 2000 4:27 PM

4Carefully remove the protective seal.

5Install the toner container into the

printer.

6Push firmly on the top of the toner con-

tainer at the positions marked PUSH

HERE.

Ifs10ep-jp.book Page 4 Friday, December 22, 2000 4:27 PM

Go to next page

☞

7Push the lock lever to the lock (LOCK)

position.

8Close the top cover.

When the printer is first

switched on after toner installa-

tion, there will be a delay of

approximately 15 minutes

before the printer gets ready to

print.

To remove the toner container

Pull the lock lever #1 to the release

(UNLOCK) position, pull the lock lever

#2, then gently remove the toner con-

tainer.

LOCK

UNLOCK

LOCK

UNLOCK

Lock Lever #2

Lock Lever #1

Ifs10ep-jp.book Page 5 Friday, December 22, 2000 4:27 PM

Connecting the Printer to the Computer

There are various ways of connecting the printer to the computer, such as throughthe

parallel interface connector or through the optional network interface board.

Printer Connections

Before performing this step, be sure to turn off both the printer and the com-

puter’s power switches and unplug the printer’s power plug from the power

outlet. Failure to do so may result in electrical shock.

A standard Centronics parallel interface connector ( ) is located on the rear of

the printer.

STEP

Printer (Rear)

OptionalSerial Interface

Board kit (IB-10E)

Parallel Interface

Network

Optional Network

Interface Board

(DC 3.3V)

Serial Interface

Power Supply

Ifs10ep-jp.book Page 6 Friday, December 22, 2000 4:27 PM

Go to next page

☞

Parallel Interface Connection

1Plug one end of the printer cable (not

included) into the parallel interface con-

nector on the rear of the printer.

•Use a parallel printer cable

that complies with the

IEEE1284 standards.

•The printer will work best if it

is installed near the computer.

The connecting cable should

be shielded and not be longer

than 3 meters (10 feet).

2Close the clips on both sides to fix the

connector in place.

Plug the other end of the printer cable

into the computer’s Centronics parallel

interface connector.

To p r i n t er

Clips

Printer Cable

Ifs10ep-jp.book Page 7 Friday, December 22, 2000 4:27 PM

Connecting the Power Cord

This section describes the procedure for connecting the power cable and various

cautions.

Notes on Power Supply

•Install the printer near an AC wall outlet, preferably one that can be used for

the printer alone.

•Only use this printer with the supply voltage indicated on the serial number

label attached to the printer’s rear panel.

•If an extension cord is used, the total length of the power cord plus extension

should be 5 meters (17 feet) or less.

Power Requirements

To Connect the Power Cord

•Be sure the printer’s power switch is turned off.

•Only use the power cord supplied with the printer.

1Plug the power cord into the power cord

connector on the rear of the printer.

2Connect the other end of the power cord

into a power outlet.

Be sure to connect to a 3-wire

grounded power strip.

Voltage 120 V (U.S.A. and Canada), 220 to 240 V (European countries, and the

Asia-Pacific region), ±10 % at each voltage

Frequency 60 Hz (120 V) ±2 %, 50/60 Hz (220 to 240 V) ±2 %

Current capacity Max. 4.4 A at 120 V, or max. 2.2 A at 230 V

STEPSTEP

Power Cord

Connector

Power Cord

Ifs10ep-jp.book Page 8 Friday, December 22, 2000 4:27 PM

Inhaltsverzeichnis

Andere Kyocera Mita Drucker Handbücher

Kyocera Mita

Kyocera Mita WP31C Bedienungsanleitung

Kyocera Mita

Kyocera Mita FS-C5016N Bedienungsanleitung

Kyocera Mita

Kyocera Mita KM-P4850w Bedienungsanleitung

Kyocera Mita

Kyocera Mita KM-P4845w Bedienungsanleitung

Kyocera Mita

Kyocera Mita Ecosys FS-1010 Bedienungsanleitung

Kyocera Mita

Kyocera Mita Ecosys FS-6020 Bedienungsanleitung

Kyocera Mita

Kyocera Mita KM-P4845w Bedienungsanleitung

Kyocera Mita

Kyocera Mita FS-6750 Bedienungsanleitung

Kyocera Mita

Kyocera Mita S-9100DN Bedienungsanleitung

Kyocera Mita

Kyocera Mita FS-C5016N Bedienungsanleitung

Kyocera Mita

Kyocera Mita Ecosys FS-6020 Bedienungsanleitung

Kyocera Mita

Kyocera Mita KM-1505 Bedienungsanleitung

Kyocera Mita

Kyocera Mita FS-9100DN Bedienungsanleitung

Kyocera Mita

Kyocera Mita FS 8000C - Color Laser Printer Bedienungsanleitung

Kyocera Mita

Kyocera Mita FS-3700 Bedienungsanleitung

Kyocera Mita

Kyocera Mita DP-2800 Handbuch

Kyocera Mita

Kyocera Mita KM-1500 Bedienungsanleitung

Kyocera Mita

Kyocera Mita FS-1050 Bedienungsanleitung

Kyocera Mita

Kyocera Mita Ecosys FS-1800+ Bedienungsanleitung

Kyocera Mita

Kyocera Mita FS-1900N Bedienungsanleitung

Kyocera Mita

Kyocera Mita Ecosys FS-1800N Bedienungsanleitung

Kyocera Mita

Kyocera Mita FS-C5016N Bedienungsanleitung

Kyocera Mita

Kyocera Mita Ecosys FS-6020 Bedienungsanleitung

Kyocera Mita

Kyocera Mita Ecosys FS-1900 Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung