Kyocera FS-1128MFP Bedienungsanleitung
2
Introduction
About this Guide
This guide explains the following setting method necessary to use this machine.
Installation of the machine
• Unpacking
• Installing Toner Container
• Loading Paper
• Connecting Cables
• Connecting Modular Cords
Operation at the machine panel
• Selecting Language
• Date and Time Settings
• Setting Network Interface Parameters
Operation at the PC
• Accessing COMMAND CENTER (Internal HTML web page)
• Sharing Folder to use Scan to SMB
• Installing Printer Driver
• Setting TWAIN Driver
• Setting WIA Driver
IMPORTANT: Please read safety information on the Operation Guide before installing
this machine.
Trademark Information
• Windows is a registered trademark of Microsoft Corporation in the U.S.A. and/or
other countries.
• Windows XP and Windows Vista are trademarks of Microsoft Corporation.
• This machine contains the software having modules developed by Independent
JPEG Group.
All other company and product names contained in this guide are trademarks or
registered trademarks of their respective companies. The designations ™ and ® will not
be used in this guide.
SETUP GUIDE 3
1 Preparations
Clearance
Environment
• Temperature: 10 to 32.5 °C (50 to 90.5 °F)
• Humidity: 15 to 80 %RH
• Power Supply: 120 V AC, 60 Hz, 7.4 A / 220 to 240 V AC, 50/60 Hz, 3.8 A
CAUTION: Be sure to provide enough space around machine. Prolonged use
without sufficient clearance may cause overheating.
Unpacking
1Unpack the machine and all its included
components.
If the machine is FS-1128MFP, the modular
cord with the attached ferrite core is
enclosed.
IMPORTANT: Place the machine in a
stable position. When carrying the printer,
always hold the right and left sides as
shown.
2Remove the packing tape and the protective sheet.
300 mm
(11-13/16")
1000 mm
(39-3/8")
500 mm
(19-11/16")
300 mm
(11-13/16")
300 mm
(11-13/16")
Preparations
4SETUP GUIDE
3Slide the Shipping Lock to the unlock
position.
IMPORTANT: When installing the Document Processor, refer to Installation Guide
attached to the Document Processor.
4Attach the Guide Case to the machine right
as required.
Installing Toner Container
1Open the front cover.
2Remove the process unit from the machine.
IMPORTANT: Place the process unit on a
clean, level surface where it will not be
exposed to any sort of impact or shock. The
drum in the process unit is sensitive to light
and should not be exposed to normal office
lighting for more than five minutes.
3Check the lock lever to the UNLOCK
position.
Shipping Lock
Guide Case
Preparations
SETUP GUIDE 5
4Shake the toner container horizontally 5 or
6 times so that the toner inside becomes
evenly distributed.
5Remove the orange protective seal.
6Align the knob on the left side of the
container with the groove in the process unit
and place the toner container into the
process unit.
7Push on the PUSH marks on the toner
container until the container clicks into
place.
8Push the lock lever back into its LOCK
position (away from you).
Preparations
6SETUP GUIDE
9Align the pins on both sides of the process
unit with the guides inside the machine, and
slide the process unit into the machine until
it stops.
10 Close the front cover.
Loading Paper
1Carefully pull the cassette all the way out of
the machine and remove the protective
packing from inside the cassette.
2Adjust the paper length by pressing in on
the release buttons and sliding paper
stopper to fit the size of the paper. The
paper sizes are marked on the bottom of the
cassette.
3Adjust the paper width by pressing in on the
release buttons and sliding the guides to fit
the width of the paper.
4Fan the paper, then tap it on a level surface
to avoid media jams or skewed printing.
Preparations
SETUP GUIDE 7
5Place the paper in the cassette, with side to
be printed downward, so that the leading
edge is aligned against the paper stopper.
IMPORTANT: Do not exceed the upper limit
of the cassette. Otherwise, it may cause
paper jams.
6Push the cassette securely all the way back
into the machine until it stops.
Connecting Cables
1Turn the power switch off (O).
Preparations
8SETUP GUIDE
2Connect the machine to the PC or your network device. When using the network
interface, remove the cap. These cables are sold separately.
Available Standard Interfaces:
3Connect the power cord to the machine and
the other end into a power outlet.
4Turn the power switch on (|). The machine
begins to warm up. The machine will begin
replenishing the toner; this will take
approximately 15 minutes.
Once the toner has been replenished,
Ready to copy will appear on the
message display.
Interface Function Necessary Cable
Network
Interface
Printer/Scanner/
Network FAX
LAN (10Base-T or 100Base-TX, Shielded)
USB Interface Printer/TWAIN/
WIA
USB2.0 compatible cable (Hi-Speed USB
compliant, Max. 5.0 m, Shielded)
Preparations
SETUP GUIDE 9
Connecting Modular Cords (FS-1128MFP only)
1Turn the power switch off (O).
2Connect the modular cord with the attached
ferrite core to the line jack (A) of the
machine. Then, connect the modular cord to
the telephone jack (B) of the machine.
3Route the cords as shown in the figure.
4Turn the power switch on (|). The machine
begins to warm up. If the mache is first
installation, it will begin replenishing the
toner; this will take approximately 15
minutes.
Once the toner has been replenished,
Ready to copy will appear on the
message display.
A
B
Preparations
10 SETUP GUIDE
Andere Handbücher für FS-1128MFP
5
Dieses Handbuch passt für folgende Modelle
2
Inhaltsverzeichnis
Andere Kyocera Multifunktionsdrucker Handbücher
Kyocera
Kyocera KM-1500 Installationshandbuch
Kyocera
Kyocera TASKalfa 250ci Bedienungsanleitung
Kyocera
Kyocera KM-F1060 Bedienungsanleitung
Kyocera
Kyocera TASKalfa 650c Bedienungsanleitung
Kyocera
Kyocera ECOSYS PA3500cx Bedienungsanleitung
Kyocera
Kyocera KM-C2520 Bedienungsanleitung
Kyocera
Kyocera KM-C2520 Einrichtungshandbuch
Kyocera
Kyocera KM-2030 Handbuch
Kyocera
Kyocera KM-1530 Handbuch
Kyocera
Kyocera TASKalfa 356ci Bedienungsanleitung
Kyocera
Kyocera TASKALFA 300I Bedienungsanleitung
Kyocera
Kyocera ECOSYS FS-3540MFP Bedienungsanleitung
Kyocera
Kyocera KM-C850D Bedienungsanleitung
Kyocera
Kyocera TASKalfa 6501i Bedienungsanleitung
Kyocera
Kyocera TASKalfa 552ci Bedienungsanleitung
Kyocera
Kyocera FS-1030D Bedienungsanleitung
Kyocera
Kyocera KM-1530 Handbuch
Kyocera
Kyocera TASKalfa 266ci Bedienungsanleitung
Kyocera
Kyocera 1815 Montageanleitung
Kyocera
Kyocera TASKalfa 650c Bedienungsanleitung
Beliebte Multifunktionsdrucker Handbücher anderer Marken
Triumph Adler
Triumph Adler DC 2016 Handbuch
Epson
Epson WorkForce WF-2510 Benutzerhandbuch
Epson
Epson Stylus Scan 2000 Installations- und Betriebshandbuch
Epson
Epson PictureMate Snap PM 240 Bedienungsanleitung
Konica Minolta
Konica Minolta bizhub C35 Bedienungsanleitung
Brother
Brother MFC-J430w Bedienungsanleitung
