Kyocera TASKalfa 1800 Bedienungsanleitung

TASKalfa 1800/1801

TASKalfa 2200/2201

DP-480/PF-480

/DU-480

SERVICE

MANUAL

Published in August 2014

842NN116

2NNSM066

Rev.6

CAUTION

RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE. DISPOSE OF USED BAT-

TERIES ACCORDING TO THE INSTRUCTIONS.

It may be illegal to dispose of this battery into the municipal waste stream. Check with your local solid waste

officials for details in your area for proper disposal.

ATTENTION

IL Y A UN RISQUE D’EXPLOSION SI LA BATTERIE EST REMPLACEE PAR UN MODELE DE TYPE

INCORRECT. METTRE AU REBUT LES BATTERIES UTILISEES SELON LES INSTRUCTIONS DONNEES.

Il peut être illégal de jeter les batteries dans des eaux d’égout municipales. Vérifiez avec les fonctionnaires

municipaux de votre région pour les détails concernant des déchets solides et une mise au rebut appropriée.

Notation of products in the manual

For the purpose of this service manual, products are identified by print speed at A4.

TASKalfa 1800/1801 :18 ppm model

TASKalfa 2200/2201 :22 ppm model

Or products are identified by correspondence of FAX.

TASKalfa 1800/2200 :Basic model

TASKalfa 1801/2201 :Advanced model

Revision history

Revision Date Pages Revised contents

1 9 September 2013 Contents Change: Page number of the contents

1-2-20

1-2-26

1-5-24

1-5-64

1-5-76

Correction: Number of the screws

1-5-27 Clerical error correction: Deleted procedure 1

1-5-29 Correction: Number of the screws

Deleted: The detaching procedure of the drum unit

1-5-33 Added: Cautions sentence of the refitting

1-5-49 Added: Procedure 7 (Performs U167)

2-1-3, 2-1-4

2-2-24, 2-3-8

2-2-8, 2-3-9

Clerical error correction: Deleted the main power switch

(MSW) and the CN5 on power source PWB

Correction: YC20 (Right cover sw (reserve))

2 11 November 2013 Cover Added: Notation of products in the manual

Contents Change: Page number of the contents

Contents

(1-3-19 to 24)

Deleted: (2)Installing the key counter (option)

1-1-2, 1-1-12

1-2-9

Deleted: The statement of an option

1-1-2 Added: Interface for Advanced model

Change: Dimension and Weight

1-1-2, 1-1-12 Added: Option(Fax system and Network interface)

1-1-3 Clerical error correction of the item :

"First Copy" was changed to "First Print".

Added: to the description of “First Print Time”

1-1-5 Change: Dimensions of Paper Feeder (PF-480)

1-1-7 Added: 28 and 29

1-1-9, 1-1-10 Added: Operation panel for Advanced model

1-2-3, 1-2-4

1-2-5

Change: Change the form of the packing material

1-2-9 Change: A paper is changed into double fold.

1-2-16, 1-2-17 Added: The cautions sentence about High Altitude

1-3-4, 1-3-59 Added: U223 Lock Panel Ope (Advanced model only)

1-3-5 to 7,

1-3-81 to 100

Added: U600 to U699 for fax

1-3-9 Change: (4) and (5)

1-3-10 Added: "Advanced model only" to (2)

1-3-13 Added: (6) Option language version

Change: Item numbers

1-3-14 Added: "Advanced model only" to (2)

: (6) Option language version

Change: Item numbers

2 11 November 2013 1-3-15 Change: Item numbers

1-3-24, 1-3-25 Change: Data digit number of [LSU Out Top] and [LSU

Out Left]

1-3-25 to 40

1-3-42

1-3-44 to 46

1-3-51 to 53

1-3-55, 1-3-63

1-3-67, 1-3-68

1-3-70

1-3-72 to 1-3-74

1-3-78 to 80

1-3-116

1-3-117, 2-3-7

Correct: added the statement of a numerical change key

1-3-37 Correction: Description of "Back Head"

1-3-42, 1-3-43 Change: Items and Initial setting of Display

1-3-44 Added: The cautions sentence about High Altitude

Correction: The contents of Display and Description

1-3-51 Correction: Procedure 2 to 4 in U140

1-3-53 Correction: Setting range value in U156

1-3-54 Correction: delete the clearing function of U158

1-3-55 Correction: Setting range value in U161

1-3-57 Clerical error correction: The display of U199 is cor-

rected.

1-3-68 Correction: Setting range value in U332

1-3-69 Added: Procedure of setting to On/Off in U341

1-3-72 to 74 Correction: Setting range value in U402 ,U403 and U404

1-3-75 Deleted: Procedure 4 “Select [Target] and ..."

1-3-112

1-3-113

Deleted: How to display the history of paper jams

1-3-116 Deleted: U928 Life Cnt

1-4-3 Clerical error correction: Code 0120, 0121

1-4-94 to 109 Added: 1-4-9 Send error code

1-4-10 Error codes

1-5-19 Clerical error correction: Change the procedure 9 and

delete the procedure 10 and Figure 1-5-30

1-5-50 Added: Detaching and refitting the exit unit

2-2-2 Added: Master file name for Advanced model

Correction: Performance number in procedure 10

2-2-8 to 10

2-3-10

Added: YC2003, YC2007

2-3-8

2-3-10

Change: Signal name of YC8

Change: Signal name of YC1, YC2010, YC2011 and CIS

2-3-11 Change: Signal name of YC2, YC3 and YC4

Revision Date Pages Revised contents

2 11 November 2013 2-3-12 Change: Signal name of YC1, YC2 and YC6

Installation

guide

Added: IB-33 and FAX System(X)

Address Change: Address on New Zealand

3 27 December 2013 Contents Change: Page numbers of the contents

1-3-79, 1-3-80 Added: “*: This setting is usually unnecessary.”

2-3-1, 2-3-2 Correction: (1) List of maintenance parts

2-3-4 to 2-3-10 Added: (3) Periodic maintenance procedures

Address Correction

4 15 Febraury 2014 Contents Change: Page numbers of the contents

1-1-2 Correction: Power source →Rated input

1-3-81, 1-3-82 Correction: The position of "Excute"

1-3-69 Added: The addition of a caution sentence

1-4-82 Correction: Corrective Action of (14)

1-4-94 Changed: Send error code list

2-3-11 Added: Comment to (2)Repetitive defects gauge

5 18 March 2014 1-3-75,

1-3-78 to 80

Correction: Part number of the original

6 28 July 2014 Contents Change: Page numbers of the contents

2-2-14, 2-2-15 Correction: Remarks on main/engine PWB replacement

Revision Date Pages Revised contents

This page is intentionally left blank.

Safety precautions

This booklet provides safety warnings and precautions for our service personnel to ensure the safety of

their customers, their machines as well as themselves during maintenance activities. Service personnel

are advised to read this booklet carefully to familiarize themselves with the warnings and precautions

described here before engaging in maintenance activities.

Safety warnings and precautions

Various symbols are used to protect our service personnel and customers from physical danger and

to prevent damage to their property. These symbols are described below:

DANGER: High risk of serious bodily injury or death may result from insufficient attention to or incorrect

compliance with warning messages using this symbol.

WARNING: Serious bodily injury or death may result from insufficient attention to or incorrect compliance

with warning messages using this symbol.

CAUTION: Bodily injury or damage to property may result from insufficient attention to or incorrect com-

pliance with warning messages using this symbol.

Symbols

The triangle ( ) symbol indicates a warning including danger and caution. The specific point of attention is

shown inside the symbol.

General warning. Warning of risk of electric shock.

Warning of high temperature.

indicates a prohibited action. The specific prohibition is shown inside the symbol.

General prohibited action. Disassembly prohibited.

indicates that action is required. The specific action required is shown inside the symbol.

General action required. Remove the power plug from the wall outlet.

Always ground the copier.

1. Installation Precautions

WARNING

• Do not use a power supply with a voltage other than that specified. Avoid multiple connections to

one outlet: they may cause fire or electric shock. When using an extension cable, always check that

it is adequate for the rated current. .....................................................................................................

• Connect the ground wire to a suitable grounding point. Not grounding the copier may cause fire or

electric shock. Connecting the earth wire to an object not approved for the purpose may cause

explosion or electric shock. Never connect the ground cable to any of the following: gas pipes, light-

ning rods, ground cables for telephone lines and water pipes or faucets not approved by the proper

authorities. ..........................................................................................................................................

CAUTION:

• Do not place the copier on an infirm or angled surface: the copier may tip over, causing injury. .........

• Do not install the copier in a humid or dusty place. This may cause fire or electric shock. .................

• Do not install the copier near a radiator, heater, other heat source or near flammable material. This

may cause fire. ...................................................................................................................................

• Allow sufficient space around the copier to allow the ventilation grills to keep the machine as cool

as possible. Insufficient ventilation may cause heat buildup and poor copying performance. ............

• Always handle the machine by the correct locations when moving it. .................................................

• Always use anti-toppling and locking devices on copiers so equipped. Failure to do this may cause

the copier to move unexpectedly or topple, leading to injury. ..............................................................

• Avoid inhaling toner or developer excessively. Protect the eyes. If toner or developer is accidentally

ingested, drink a lot of water to dilute it in the stomach and obtain medical attention immediately.

If it gets into the eyes, rinse immediately with copious amounts of water and obtain medical atten-

tion. .....................................................................................................................................................

• Advice customers that they must always follow the safety warnings and precautions in the copier’s

instruction handbook. .........................................................................................................................

2. Precautions for Maintenance

WARNING

• Always remove the power plug from the wall outlet before starting machine disassembly. ................

• Always follow the procedures for maintenance described in the service manual and other related

brochures. ..........................................................................................................................................

• Under no circumstances attempt to bypass or disable safety features including safety mechanisms

and protective circuits. ........................................................................................................................

• Always use parts having the correct specifications. ............................................................................

• Always use the thermostat or thermal fuse specified in the service manual or other related brochure

when replacing them. Using a piece of wire, for example, could lead to fire or other serious acci-

dent. ...................................................................................................................................................

• When the service manual or other serious brochure specifies a distance or gap for installation of a

part, always use the correct scale and measure carefully. ..................................................................

• Always check that the copier is correctly connected to an outlet with a ground connection. ...............

• Check that the power cable covering is free of damage. Check that the power plug is dust-free. If it

is dirty, clean it to remove the risk of fire or electric shock. .................................................................

• Never attempt to disassemble the optical unit in machines using lasers. Leaking laser light may

damage eyesight. ...............................................................................................................................

• Handle the charger sections with care. They are charged to high potentials and may cause electric

shock if handled improperly. ...............................................................................................................

CAUTION

• Wear safe clothing. If wearing loose clothing or accessories such as ties, make sure they are safely

secured so they will not be caught in rotating sections. ......................................................................

• Use utmost caution when working on a powered machine. Keep away from chains and belts. ..........

• Handle the fixing section with care to avoid burns as it can be extremely hot. ..................................

• Check that the fixing unit thermistor, heat and press rollers are clean. Dirt on them can cause

abnormally high temperatures. ...........................................................................................................

Andere Handbücher für TASKalfa 1800

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Kyocera Multifunktionsdrucker Handbücher

Kyocera

Kyocera ECOSYS FS-9130DN Bedienungsanleitung

Kyocera

Kyocera 13600 Leitfaden

Kyocera

Kyocera ECOSYS M3550idn Bedienungsanleitung

Kyocera

Kyocera ECOSYS M2040dn Bedienungsanleitung

Kyocera

Kyocera KM-2540 Bedienungsanleitung

Kyocera

Kyocera KM-2560 Bedienungsanleitung

Kyocera

Kyocera TASKalfa 250ci Bedienungsanleitung

Kyocera

Kyocera 6003i Bedienungsanleitung

Kyocera

Kyocera TASKalfa 2021 Gebrauchsanweisung

Kyocera

Kyocera KM-C2630D Bedienungsanleitung

Kyocera

Kyocera KM-4035 Bedienungsanleitung

Kyocera

Kyocera FS-C2026MFP Bedienungsanleitung

Kyocera

Kyocera TASKalfa 420i Bedienungsanleitung

Kyocera

Kyocera FS-2100DN Bedienungsanleitung

Kyocera

Kyocera TASKalfa 266ci Bedienungsanleitung

Kyocera

Kyocera ECOSYS M6026cidn Bauanleitung

Kyocera

Kyocera TASKalfa 420i Bedienungsanleitung

Kyocera

Kyocera FS-9120DN Bedienungsanleitung

Kyocera

Kyocera ECOSYS M6026cidn Bedienungsanleitung

Kyocera

Kyocera KM-C850 Einrichtungshandbuch

Kyocera

Kyocera FS-1116MFP Bedienungsanleitung

Kyocera

Kyocera TASKalfa 4500i Bedienungsanleitung

Kyocera

Kyocera TASKalfa 181 Bedienungsanleitung

Kyocera

Kyocera TASKalfa 255 Bedienungsanleitung

Beliebte Multifunktionsdrucker Handbücher anderer Marken

Triumph Adler

Triumph Adler DC 2016 Handbuch

Epson

Epson WorkForce WF-2510 Benutzerhandbuch

Epson

Epson Stylus Scan 2000 Installations- und Betriebshandbuch

Epson

Epson PictureMate Snap PM 240 Bedienungsanleitung

Konica Minolta

Konica Minolta bizhub C35 Bedienungsanleitung

Brother

Brother MFC-J430w Bedienungsanleitung

Konica Minolta

Konica Minolta BIZHUB 558 Bedienungsanleitung

Lexmark

Lexmark MX710 Series Handbuch

Brother

Brother MFC-9760 Bedienungsanleitung

Lexmark

Lexmark XC8155 Bedienungsanleitung

Lexmark

Lexmark X642E Bedienungsanleitung

Sharp

Sharp MX-2310U Leitfaden

Aficio

Aficio 200 Bedienungsanleitung

Canon

Canon ImageCLASS 2300 Handbuch

Ricoh

Ricoh Pro C900 Bedienungsanleitung

Lexmark

Lexmark X925 Bedienungsanleitung

Brother

Brother Business Smart MFC-J4510dw Bedienungsanleitung

Epson

Epson Stylus CX8400 Series Bedienungsanleitung