Kyocera TASKalfa 306ci Bedienungsanleitung

TASKalfa 306ci

TASKalfa 356ci

TASKalfa 406ci

PF-5120/5130/5140

DP-5100/5110

AK-5100/JS-5100

DF-5100/5110/5120

PH-5100/5110/MT-5100

FAX System 10/11

SERVICE

MANUAL

Published in February 2016

842R4114

2R4SM064

Rev.4

2R4/2R5/2R6

6-1

6 Maintenance mode

6-1 Maintenance mode

The machine is equipped with a maintenance function which can be used to maintain and service the

machine.

(1) Executing the maintenance mode

Enter “10871087” using

the numeric keys.

Enter the maintenance item

number using the [▲] [▼] keys

or numeric keys.

The selected maintenance item is run.

Press the stop key.

Press the start key.

Start

End

Maintenance mode is entered.

The maintenance item is selected.

Maintenance mode is exited.

Repeat the same

maintenance item?

Run another maintenance

item?

Yes

Enter 001 using the [▲] [▼] keys

or numeric keys

and press the start key.

2R4/2R5/2R6-2

6-2

(2) Maintenance modes list (30ppm model)

Section No. Maintenance item Outline

General U000 Printing Maintenance Report Printing the reports and exporting them to a

USB memory

U001 Exiting the maintenance mode Exiting from the maintenance mode

U002 Set Factory Default Initializing to the factory-default setting

U004 Machine serial number Display of the machine serial number and set-

ting

U010 Setting the maintenance mode ID Setting the maintenance mode ID

U019 Firmware Version Displays the firmware version of the PWB

Initializa-

tion

U021 Initializes Memory Initializing the backup RAM

U025 Firmware update (S) Updates the firmware

Drive

Paper

feed

Convey-

ing

Cooling

U030 Motor operation check Drive the drive motor

U031 Check the conveying switch Check the conveying switch On/Off

U032 Clutch operation check Check the paper conveying clutch operation

U033 Solenoid operation check Drive the paper conveying and toner supply

solenoids

U034 Paper timing adjustment Adjusting the leading edge timing and the center

line

U035 Folio size setting Sets the Folio paper length and width.

U037 Fan motor operation check Drive each fan motor.

U051 Registration paper loop amount

adjustment

Adjusts the paper loop amount between the roll-

ers

U053 Adjusting the motor speed Sets each motor's speed correction

U059 Fan mode setting Sets the drive mode of the conveying fan motor

Optical U065 Adjusting the magnification for table

scanning

Adjusting the magnification for table scanning

U066 Adjusting the table scanning timing Adjusting the leading edge timing for table scan-

ning

U067 Adjusting the table scanning center

line

Adjusting the center line for table scanning

U068 DP scanning position adjustment Adjusting the starting position for DP scanning

U070 DP magnification adjustment Adjusting the magnification for DP scanning

U071 Adjusting the DP leading edge Tim-

ing

Adjusting the DP scanning timing

U072 Adjusting the DP original center Adjusting the center line for DP scanning

U089 MIP-PG pattern output Output MIP-PG pattern

2R4/2R5/2R6

6-3

High volt-

age sys-

tem

U100 Main high voltage adjustment Adjust the drum surface potential

U101 Primary transfer voltage adjustment Sets high voltage except the main high voltage

and outputs

U106 Secondary transfer voltage adjust-

ment

Set the secondary transfer voltage correction

U107 Primary transfer cleaning voltage

adjustment

Set the primary transfer belt cleaning voltage

U110 Drum counter Displays/sets the drum counter

U117 Drum unit number Displays the drum number

U118 Drum unit history Displays the drum history

U119 Setting the drum Sets the initial LSU light intensity

U120 Drum drive distance counter Displays the drum drive distance counter

U127 Clearing the transfer count Displaying the counts

U128 Leading edge timing Adjust the transfer high-voltage output ON/OFF

timing

Devel-

oper sys-

tem

U132 Forcible toner supply operation Execute the toner supply in the toner control

level

U135 Checking the toner motor operation Drives the toner motor

U136 Toner level detection setting Sets the number of pages printable at toner near

end

U139 Temperature, humidity Displays the machine inside and outside humid-

ity

U140 Developer bias adjustment Adjust the developer bias values or set the high

altitude mode.

U147 Setting the toner applying mode Sets the overcharge toner removal mode

U148 Drum refresh mode setting Setting auto drum refresh

U155 Toner sensor output Displays the toner sensor output

U156 Toner control level adjustment Displays/adjusts the toner supply level

U157 Developer drive time Displays/sets the developer drive time

U158 Developer counter Displays/sets the developer counter

Fuser U161 Fuser temperature adjustment Sets the fuser control temperature

U167 Clearing the fuser count Displaying/clearing the counts

U199 Fuser temperature Monitor the fuser temperature

Section No. Maintenance item Outline

2R4/2R5/2R6

6-4

Opera-

tion sec-

tion

Support

equip-

ment

U200 All LEDs lighting Light all the LEDs on the operation panel

U201 Initializing the touch panel Correct the X and Y axis position of the touch

panel

U203 Check DP operation Checking the DP paper conveying operation

with the DP alone

U207 Operation key check Check the operation panel key operation

U211 Enhancement unit connection set-

ting

Sets the connection of the enhancement units

U221 USB host lock function setting Sets USB Host lock function ON/OFF

U222 Setting the IC card type Sets the ID card type

U223 Operation panel lock Set On/Off of the operation unit lock

U230 Optional device serial number Displays the optional device serial number

U240 Finisher operation check Checks the drive operation

U241 Finisher switch check Check the switch operation

U243 Checking the DP motor Drive the PF motor and solenoid

U244 DP switch check Drive the DP sensor

U246 Finisher adjustment Sets the finisher adjustment value

U247 Paper feed operation check Drives the PF motor and clutch

Mode

Setting

U250 Checking/clearing the maintenance

cycle

Changes the preset value

U251 Checking/clearing the maintenance

counter

Displaying/clearing/changing the counter value

U252 Destination Sets the machine operation and indication

depending on the specification of the destination

U253 Switching the double/single counts Sets the counter by color mode

U260 Switching the timing for copy count-

ing

Setting the count-up timing

U265 Setting by destination Sets the OEM code

U276 Switching the copy count mode Set the single color copy count mode

U278 Delivery date setting Register Delivery Date

U284 Setting the 2-color copy Switches the 2-color copy mode

U285 Set Service Status Page Setting the print coverage report output

U290 Setting the drive to save the HyPAS

application

Sets the drive to save the HyPAS application

U323 Abnormal temperature and humidity

notification setting

Switches the indication mode of the abnormal

temperature and humidity detection

U325 Paper interval setting Sets the print interval at high coverage

U326 Black line cleaning indication Switch the black line cleaning guidance indica-

tion

U327 Cassette heater On/Off setting Selects the cassette heater control setting

Section No. Maintenance item Outline

2R4/2R5/2R6

6-5

Mode

Setting

U332 Adjusting the black coverage coeffi-

cient

Setting the coefficient of the custom size

U341 Printer cassette setting Sets the cassette to printer output only

U343 Duplex priority mode Switches the duplex printing priority mode

U345 Setting the value for maintenance

due indication

Setting the maintenance timing display

U346 Selecting Sleep Mode Setting the BAM related sleep mode

Image

process-

ing

U402 Adjusting the printing margins Adjusts the scan image margins

U403 Adjusting margins for scanning an

original on the contact glass

Adjusts the margin for scanning originals

U404 Adjusting margins for scanning an

original from the document proces-

sor

Adjusts the margin for scanning originals

U407 Adjusting the writing timing (Duplex/

Reversal)

Adjusting the writing timing when duplex printing

U410 Adjusting the halftone automatically Acquiring the data for the automatic halftone

adjustment and the ID correction

U411 Scanner auto adjustment Adjusting the scanner and DP automatically

U425 Set Target Inputs the Lab value printed on an adjustment

original

U429 Adjusting the color balance offset Adjusts the color balance offset

U464 ID correction setting Sets the ID correction

U465 ID correction data Displays the light intensity control value after the

ID correction

U467 Color registration correction opera-

tion setting

Sets the color registration correction

U468 Color registration correction data Displays the color registration correction data

U469 Color registration adjustment Corrects the color registration

U470 Setting the JPEG compression rate Sets the JPEG compression rate

Image

process-

ing

U474 Checking the LSU cleaning Sets the LSU cleaning operation check and

cleaning cycle

U485 Image process mode setting Sets the image processing

U486 Color/BW mode setting Sets the image processing

U520 TDRS setting Checking/setting the TDRS

Section No. Maintenance item Outline

2R4/2R5/2R6

6-6

FAX U600 Initialize: All Data Initializes all data and image memory.

U601 Initialize: Keep data Initializing the software switches of other than

the machine data

U603 User data 1 Makes user settings to enable the use as a FAX

U604 User data 2 Makes user settings to enable the use as a FAX

U605 Data clear Initializing the FAX communication data

U610 System 1 Set the number of lines to be ignored when

receiving a FAX at 100% magnification and in

the auto reduction mode.

U611 System 2 Number of adjustment lines for automatic reduc-

tion.

U612 System 3 Setting regarding the FAX communication oper-

ation

U620 FAX system Sets the signal detection method for remote

switching

U625 Communication settings Sets the auto redialing interval and the number

of times of auto redialing

U630 Communication control procedures

Setting the FAX communication

U631 Communication control procedures

Sets the FAX communication

U632 Communication control procedures

Setting the FAX communication

U633 Communication control procedures

Setting the FAX communication

U634 Communication control procedures

Set the acceptable error when judging the

received TCF signal

U640 Communication time setting 1 Setting the detection time by remote switching

mode

U641 Communication time setting 2 Sets the time-out time for the fax communication

U650 Modem 1 Sets the G3 transmission cable equalizer

U651 Modem 2 Sets the modem output level

U660 Ring setting Setting the NCU (network control unit)

U670 List output Outputting the list of the FAX communication

data

U695 FAX function customization FAX batch transmission is set up.

U699 Software switch: Set Sets the software switches individually

Section No. Maintenance item Outline

2R4/2R5/2R6-4

6-7

Others U901 Clearing the counters by paper

source

Displays/clears the counters by paper source

U903 Clearing the jam counter Displays/clears number of occurrence by jam

trigger code

U904 Clearing the service call error coun-

ter

Displays/clears the service call error and system

error counts

U905 Optional counter Displaying the counts

U906 Resetting the partial operation Resets the partial operation

U908 Total counter Displays the FAX count

U910 Black rate data Clearing the print coverage data and its period

U911 Counter by media type Displays/clears the counts by media type

U917 Read/Write Backup Data Reading/writing the backup data to a USB mem-

ory

U920 Billing counter Displays the billing count

U927 Clearing all the billing/life counters Clearing the billing count and machine life count

U928 Machine life counter Displays the machine life count

U930 Clear the main charger roller counts Displaying/setting the counts

U952 MMaintenance mode workflow Execute the maintenance flow with the Work-

Flow data

U964 Log check Transfer the log files to a USB memory

U969 Toner area code Displays the toner area code

U977 Setting the data capture mode Stores the data sent to the main unit into a USB

memory

U984 Developer unit number Displays the developer unit number

U985 Developer unit history Displays the developer unit number history

U991 Scanner counter Displays the scanner count

Section No. Maintenance item Outline

2R4/2R5/2R6

6-8

(2-1) Content of the maintenance mode (30ppm model)

Contents

Prints the list of the current settings of the maintenance items, paper jam and service call error

occurrences. Output the event log and service status page.

Also, sends output data to a USB memory.

Purpose

Checks the current settings of the maintenance items, paper jam and service call error occur-

rences.

Before initializing or replacing the backup memory, print the list of the current settings of the

maintenance items to reenter the settings after initialization or replacement.

Method

1.Press the [Start] key.

2.Select the item to output.

3.Turn it On/Off by the [Ż] [Ź] keys.

4.Press the [Start] key.

* :Insert a USB memory into the USB memory slot to output to it.

5.Select the item to output.

6.Press the [Start] key to output the list.

* :If A4 paper is available, it is output with this size. If A4 paper is unavailable, sekect the paper

source. Output status is displayed.

* :The output data is sent to the USB memory.

Completion

Press the [Stop] key.

* :The screen for selecting a maintenance item No. is displayed.

U000 Printing Maintenance Report

(Message: Mainte Report)

Items Output list

Maintenance Maintenance mode setting list

User Status Output User Status Page

Service Status Output Service Status Page

Event Output the event log report

Network Status Output Network Status Page

All All reports output

Items Output list

Print A report is printed.

USB(Text) Destination: send to USB memory (text format)

USB(HTML) Destination: send to USB memory (HTML format)

2R4/2R5/2R6

6-9

Detail of event log

Figure 6-1

2014/10/19 15:15

[XXXXXXXX]

[XXXXXXXX] [XXXXXXXX]

Paper Jam Log Counter Log

J0000:

J0100:

J0101:

J0104:

J0105:

J0106:

J0107:

J0110:

J0111:

J0211:

J0212:

J0213:

J0501:

J0502:

J0503:

J0504:

J0508:

J0509:

J0512:

J0511:

J0513:

J0514:

J0518:

J0519:

J1403:

J1404:

J1413:

J1414:

J1604:

J1614:

J4002:

J4003:

J4004:

J4009:

J4012:

J4013:

J4014:

J4019:

J4201:

J4202:

J4203:

J4204:

222

999

J9200:

J9210:

J9220:

J4302:

J4303:

J4304:

J4309:

J9000:

J9004 0

J9010:

J9060:

J9061:

J9062:

1J9110:

J9120: 0

C0000:

C0001:

C0002:

C0003:

C0004:

C0005:

C0006:

C0007:

C0008:

C0009:

C0010:

C0011:

C0012:

C0013:

C0014:

C0015:

C0016:

C0017:

C0018:

C0019:

C0020:

C0021:

C0022:

C0023:

T00:

M00:

M02:

Count.

5555555

4444444

3333333

2222222

1111111

999999

888888

777777

666666

555555

444444

Event Descriprions Date and Time

0501.01.08.01.00 2014/02/12 17:30

2014/02/12 17:30

4002.01.08.01.00

0501.01.08.01.00

4002.01.08.01.00

0501.01.08.01.00

4002.01.08.01.00

0501.01.08.01.00

4002.01.08.01

0501.01.08.01

4002.01.08.01

0501.01.08.01.00

4002.01.08.01.00

Service Call Log

Count.

1111111

999999

888888

777777

666666

555555

444444

Service Code

01.6000

01.2100

01.4000

01.6000

01.2100

01.4000

01.6000

01.2100

Maintenance Log

# Count. Item.

Unknown toner Log

Count.

1111111

999999

888888

777777

666666

Item.

01.00

Event Log

MFP

TASKalfa 406ci

Firmware version 2R6_2000.000.000 2014.09.19

[XXXXXXXXXX]

999999

888888

777777

666666

555555

444444

01.21

01.40

01.60

01.21

01.40

01.60

01.21

Data and Time

2014/02/12 17:30

Data and Time

2014/02/12 17:30

Data and Time

2014/02/12 17:30

J4208:

J4209:

J4211:

J4218:

J4212:

J4213:

222

J4214:

J4301:

J4219:

(2)

(4)

(3) (5)

(f)

(g)

(h)

(11)

(7)

(8)

(9)

(10)

(1)

(6)

0501.01.08.01.00

(a) (b) (c) (d) (e)

Andere Handbücher für TASKalfa 306ci

Dieses Handbuch passt für folgende Modelle

Andere Kyocera Drucker Handbücher

Kyocera

Kyocera ECOSYS FS-C8520MFP Installations- und Betriebshandbuch

Kyocera

Kyocera PA2001w Bedienungsanleitung

Kyocera

Kyocera ECOSYS P3155dn Bedienungsanleitung

Kyocera

Kyocera C8100DN - Color Laser Printer Gebrauchs- und Pflegehandbuch

Kyocera

Kyocera ECOSYS P2135dn Bedienungsanleitung

Kyocera

Kyocera ECOSYS FS-C5150DN Bedienungsanleitung

Kyocera

Kyocera ECOSYS P3045dn Bedienungsanleitung

Kyocera

Kyocera FS-1020MFP Bedienungsanleitung

Kyocera

Kyocera FS FS-1020D Bedienungsanleitung

Kyocera

Kyocera FS-2000D, FS-3900DN, FS-4000DN, FS-6950DN Bedienungsanleitung

Kyocera

Kyocera Ecosys P2235dw Bedienungsanleitung

Kyocera

Kyocera ECOSYS M6026cdn Type B Bedienungsanleitung

Kyocera

Kyocera ECOSYS M4132idn Bedienungsanleitung

Kyocera

Kyocera ECOSYS FS-6950DN Bedienungsanleitung

Kyocera

Kyocera FS-3040MFP Bedienungsanleitung

Kyocera

Kyocera KM-4530 Bedienungsanleitung

Kyocera

Kyocera ECOSYS FS-1370DN Bedienungsanleitung

Kyocera

Kyocera FS-9530DN Bedienungsanleitung

Kyocera

Kyocera ECOSYS M3145idn Bedienungsanleitung

Kyocera

Kyocera FS-1100 Bedienungsanleitung

Kyocera

Kyocera TASKalfa 3212i Bedienungsanleitung

Kyocera

Kyocera FS FS-C8500DN Bedienungsanleitung

Kyocera

Kyocera Ecosys FS-1320D Bedienungsanleitung

Kyocera

Kyocera ECOSYS PA6000 Series Bedienungsanleitung

Beliebte Drucker Handbücher anderer Marken

Lexmark

Lexmark 1400 Series Handbuch

Canon

Canon i70 Series Bedienungsanleitung

Evolis

Evolis Elypso Bedienungsanleitung

Canon

Canon LASER SHOT LBP-1210 Bedienungsanleitung

Samsung

Samsung BIXOLON SRP-350plusF Bedienungsanleitung

Canon

Canon PIXMA PRO-1 Series Bedienungsanleitung

Canon

Canon PIXMA G3560 Einrichtungshandbuch

Dell

Dell Color Laser Printer 2130cn Bedienungsanleitung

Tektronix

Tektronix Phaser 840 Bedienungsanleitung

Epson

Epson ET-7750 Betriebsanleitung

Canon

Canon CLBR 460ps Bedienungsanleitung

Eltron

Eltron P210 Guide Bedienungsanleitung

Ricoh

Ricoh MD-P1 Bedienungsanleitung

Epson

Epson SC-F7100 series Bedienungsanleitung

Epson

Epson Stylus C40UX Bedienungsanleitung

Canon

Canon imagePASS-A2 Bedienungsanleitung

Canon

Canon S820D Bedienungsanleitung

IRA3D

IRA3D POETRY4 Bedienungsanleitung