La Crosse Technology WT-5120 Bedienungsanleitung

868 MHz RADIO CONTROLLED PROJECTION ALARM CLOCK

Instructions manual

INTRODUCTION

Congratulations on purchasing this innovative 868MHz projection alarm clock which

displays indoor and outdoor temperature. To enjoy the full enefits of this innovative

product, please read this operating manual.

PROJECTION ALARM CLOCK

FEATURES

•

DCF-77 Radio controlled time with manual setting option

•

12/24 hours time display (hour, minutes, seconds)

•

Projection of time (hour and minute) and outdoor temperature

•

Projection with adjusta le rightness and projection orientation possi le

•

Calendar display

Battery

compartment

Stand

Adapter socket

Function

keys

LCD

Display

•

Alarm setting with snooze function

•

Time zone setting ±12hours

•

Temperature display in ºC/ ºF

•

Indoor and outdoor temperature display

•

E.L. ack-light

•

Wireless transmission at 868 MHz

•

Signal reception intervals at 4 seconds

•

Low attery indicator

TEMPERATURE TRANSMITTER

•

Remote transmission of outdoor temperature to the

Projection clock y 868 MHz signal

•

Wall mounting case

•

Mounting at a sheltered place. Avoid direct rain and

sunshine

TO INSTALL AND REPLACE BATTERIES INTO THE PROJECTION

CLOCK

The Projection clock uses 2 x AA, IEC LR6, 1.5V atteries. To install and replace the

atteries, please follow the steps elow:

1. Insert finger or other solid o ject in the

space at the ottom center of the attery

compartment and lift up to remove the

cover.

2. Insert atteries o serving the correct

polarity (see marking).

3. Replace compartment cover.

In addition or instead of inserting batteries, the AC adapter can be used

1. Connect the power adapter to a wall socket

2. Insert the adapter into the jack at the ottom of the clock

3. The Projection clock will now start receiving the DCF time signal. After

approximately 3 to 5 minutes, the DCF time will e displayed (Also see "Setting

up" elow).

Important!

Use only the adapter provided with the projection

clock and make sure that your household voltage

is appropriate to the working voltage of the

transformer. Otherwise your Projection clock may

e damaged.

POWER SUPPLIED BY BATTERIES AND AC/DC ADAPTER

If the Projection clock is first powered y atteries and the power adapter is

su sequently used for extended period of time, the main power source of the Projection

clock will switch to AC/DC power. The atteries will then act as a ackup power source

in case of power failure.

TO INSTALL AND REPLACE BATTERIES IN THE TEMPERATURE

TRANSMITTER

The temperature transmitter uses 2 x AA, IEC, LR6, 1.5V atteries.

To install and replace the atteries, please follow the steps elow:

1. Remove the cover.

2. Insert the atteries, o serving the correct polarity (see

marking).

3. Replace the attery cover on the unit.

Note:

In the event of changing atteries in any of the units, all units need to e reset y

following the setting up procedures. This is ecause a random security code is

assigned y the transmitter at start-up and this code must e received and stored y

the Projection alarm clock in the first three minutes of power eing supplied to it.

SETTING UP

The Projection clock can be batteries operated or powered by the provided 3.4V

AC/DC adapter.

1. First, insert 2 x AA, IEC LR6, 1.5V atteries into the projection clock (or use the

A/C adapter to power up). Once the atteries are in place, all segments of the

LCD will light up riefly. Then the indoor temperature, the time as 0:00, will e

displayed. If the indoor temperature is not displayed after a few seconds, remove

the atteries and wait for at least 1 minute efore reinserting them. Once the

indoor data is displayed proceed to step 2.

2. Within 1-1/2 minutes of activating the Projection clock, place 2 x AA, IEC LR6,

1.5V atteries into the transmitter.

3. After a few seconds of inserting the atteries into the transmitter, the projection

clock will start receiving data from the transmitter. The remote temperature will

then e displayed on the clock. If this does not happen after 2 minutes, the

atteries will need to e removed from oth units and reset from step 1.

4. When the transmitter is set up, there is a testing period. Then DCF-77 time code

reception is automatically started just after the clock is activated. This takes

typically etween 3-5 minutes in good conditions. This time period is an excellent

opportunity to locate the transmitter in suita le location outdoors. In order to

ensure sufficient 868 MHz transmission however, the distance etween the

Projection clock and the transmitter should not e more than 100 meters (see

notes on “Positioning” and “868 MHz Reception”).

5. If after 10 minutes the DCF time has not een received, use the MODE/ MIN key

to manually enter a time (and date) initially. The clock will automatically attempt to

receive the DCF time each day at 2:00 am. When this is successful, the received

time will override the manually set time.

Note:

Should the total time of inserting the atteries into the transmitter take longer than 1-1/2

minutes from the time of inserting the atteries into the projection clock then

temperature reception pro lems may occur. If the temperature is not eing received,

then see "868MHz reception", efore resetting the units.

In the event of changing atteries to the transmitter, the projection clock needs to e

reset. (See Resetting the projection clock)

RESETTING THE PROJECTION CLOCK

To reset the Projection clock to the factory default setting or in case of a malfunction or

changing atteries to transmitter, please remove all atteries from the unit and unplug

the AC/DC adapter from any power source. Wait at least for 3 minutes efore powering

up the Projection clock again.

BATTERY CHANGE

It is recommended to replace the atteries in all units on an annual asis to ensure

optimum accuracy of these units.

Please participate in the preservation of the environment. Return used

batteries to an authorized depot.

PROJECTION OF TIME / OUTDOOR TEMPERATURE

Note:

The projection is a red light, not harmful under normal usage, yet care should e taken

to avoid looking directly into the light.

1. When plugged into an AC outlet, the projection alarm can continuously project the

time and the outdoor temperature

2. When operating on atteries alone, the projection alarm will only project when the

SNOOZE utton is pressed or the alarm is sounding.

3. The projection will auto-focus for display from a out 1.7 to 2.0 metres away. A

dark surrounding will e necessary to clearly see the projection.

The direction of the display can also e rotated 360° in 90° increments y pressing the

Projection Direction

utton. The projector case can e rotated 180° to further help

orient the projected display.

Andere Handbücher für WT-5120

Inhaltsverzeichnis

Andere La Crosse Technology Wecker Handbücher

La Crosse Technology

La Crosse Technology C79141-UK Bedienungsanleitung

La Crosse Technology

La Crosse Technology 616A-1908 Abmessungen

La Crosse Technology

La Crosse Technology 616-143v3v2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology W88723v2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WT-5720TWC Bedienungsanleitung

La Crosse Technology

La Crosse Technology W85923V4 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WT-2191A Bedienungsanleitung

La Crosse Technology

La Crosse Technology 616-146A Abmessungen

La Crosse Technology

La Crosse Technology WT-5431 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 616-1950 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WT-2171 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 616A-56647 Bedienungsanleitung

La Crosse Technology

La Crosse Technology C82929V2 Abmessungen

La Crosse Technology

La Crosse Technology Soluna C79141 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 616-1950V2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-8256U Bedienungsanleitung

La Crosse Technology

La Crosse Technology C85183 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WT-5130 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WT-2171 Bedienungsanleitung

La Crosse Technology

La Crosse Technology SOLUNA Bedienungsanleitung

La Crosse Technology

La Crosse Technology 433 MHz RADIO CONTROLLED PROJECTIONALARM... Bedienungsanleitung

La Crosse Technology

La Crosse Technology 616-1412v3 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 617-1270 Installationsanleitung

La Crosse Technology

La Crosse Technology WT-2160U Bedienungsanleitung

Beliebte Wecker Handbücher anderer Marken

Steren

Steren CLK-210 Bedienungsanleitung

COP-USA

COP-USA ALCDVR32-SL Bedienungsanleitung

Philips

Philips HF3505/70 Technisches Handbuch

Casio

Casio PQ-70 Bedienungsanleitung

iHome

iHome IA63 Bedienungsanleitung

Coopers

Coopers 9765 Bedienungsanleitung

ANJANK

ANJANK AC-190 Leitfaden

TFA

TFA 98.1075 Bedienungsanleitung

Sharper Image

Sharper Image 204050 Bedienungsanleitung

Lumie

Lumie Zest Bedienungsanleitung

Dexford

Dexford RCT200 Bedienungsanleitung

Philips

Philips AJL303/37B Bedienungsanleitung

RST

RST Q754 Bedienungsanleitung

iHome

iHome iKT50 Bedienungsanleitung

Sony

Sony dash HID-B7 Bedienungsanleitung

SVINZ

SVINZ SCC009 Bedienungsanleitung

Clas Ohlson

Clas Ohlson 918863 Bedienungsanleitung

IKEA

IKEA FNURRA Bedienungsanleitung