La Crosse Technology WT-3181X1 Bedienungsanleitung

 
La Crosse Technology, Ltd  Page 1 
 
WT-3181X1 FAQS 
The links below will work in most PDF viewers and link to the topic area by clicking the link. We 
recommend Adobe Reader version 10 or greater available at: http://get.adobe.com/reader 
CONTENTS 
WT-3181x1 FAQS..................................................................................................................... 1 
Batteries................................................................................................................................. 1 
Battery Life............................................................................................................................. 2 
Atomic Clock Factory Restart................................................................................................. 2 
Supported Time Zones........................................................................................................... 2 
Time is Incorrect..................................................................................................................... 2 
Clock is incorrect by Hours but minutes are correct................................................................ 2 
Daylight Saving Time.............................................................................................................. 2 
Manually Set Time.................................................................................................................. 3 
How long will the battery last? ................................................................................................ 3 
Can I shut off the WWVB signal?............................................................................................ 3 
Is there a booster antenna to receive the WWVB signal in a difficult location? ....................... 3 
Can I wire a control timing circuit to the La Crosse Technology®atomic clock?...................... 3 
Why do the hands spin once or twice everyday?.................................................................... 3 
Hands spin non-stop............................................................................................................... 3 
Hands jumps or jerks around the dial ..................................................................................... 3 
Hands stuck at certain time .................................................................................................... 4 
Hands are loose..................................................................................................................... 4 
Position the Clock................................................................................................................... 4 
How do I adjust the Temperature or Humidity?....................................................................... 4 
 
BATTERIES 
 
Explanation: Many problems are resolved with fresh batteries of the appropriate voltage. Many 
items sent in under warranty work when tested with fresh batteries. Good fresh batteries are 
important for best performance in your sensor and as backup in your clock. 
•Batteries with an expiration date of 2029, were manufactured in 2019. 
•We recommend batteries with an expiration date no more than 6 years in advance of the 
current year for best performance. 
•A minimum voltage of 1.48 v per battery is required for best performance. 
•We suggest a name-brand Alkaline battery. 
•A minimum voltage of 1.48V is necessary for proper performance. 
•Good name-brand batteries make less noise, which reduces the chance of RF (radio 
frequency) interference from the battery compartment. 
 
 

La Crosse Technology, Ltd Page 2

BATTERY LIFE

•Battery life is over 24 months

ATOMIC CLOCK FACTORY RESTART

Explanation: The factory restart returns the atomic clock to an “out-of-the-box” state and often

resolves an issue.

Factory Restart:

1. Remove all batteries from the clock for 15 minutes.

2. Press the Manual Set Tab at least 20 times to clear all memory.

3. Insert two fresh Alkaline batteries into the clock.

4. The hands will spin to 12:00, 4:00 or 8:00 and wait for the WWVB time signal.

SUPPORTED TIME ZONES

•This atomic clock offers 4 time zones: Pacific, Mountain, Central and Eastern.

•La Crosse Technology® does not make an analog clock with more than four time zones.

•The atomic clock works in North America.

•Outside of North America, the atomic clock will not receive a WWVB signal, but will keep

time like a quartz clock if manually set.

TIME IS INCORRECT

•Indicative of non-receipt of WWVB signal

•Electrical storms between you and Colorado can interfere with the WWVB signal

•Replace battery and perform restart procedure. Allow up to 5 days to receive a signal.

•Reposition the atomic clock with the front or back facing Colorado.

•Try a different location, ideally near a window. The clock should be at least six feet from

computers, TVs, air conditioners, other atomic clocks and other electrical appliances that

cause interference.

•Large buildings, metal roofed buildings and buildings or rooms full of electrical and/or radio

equipment make it difficult to receive the WWVB time signal.

CLOCK IS INCORRECT BY HOURS BUT MINUTES ARE CORRECT

•This is a Time Zone issue. Hold your Time Zone button for 5 seconds. The clock should

correct itself.

•Check that DST is on. Press and release the small, unmarked gray button between the ET

and CT button one time.

DAYLIGHT SAVING TIME

•Dependent on your location, position of the clock in your home, and atmospheric

interference, it may take up to 5 nights for the change from Daylight Savings Time to

Standard Time and vice-versa to occur.

•Press the DST indicator once. If the indicator is OFF the clock will not change. (Default is

ON).

•Check for fresh batteries. Without proper batteries, the antenna will have a harder time

picking up the signal.

La Crosse Technology, Ltd Page 3

•Position the atomic clock in a window (with the front or back) facing Ft. Collins, Colorado

and leave for up to five nights. If you do not have a window facing this direction, position the

clock near an outside wall and point the unit in this general direction.

MANUALLY SET TIME

•Remove battery for 15 minutes and press the Manual Set Tab 20 times.

•After 15 minutes, insert the battery and allow the clock to spin to 12:00, 4:00 or 8:00.

•Hold the Manual Set Tab and the hand will spin. Continue holding to reach the correct time.

Note: You can only set the clock manually for about 2 minutes after inserting the battery. If

the clock receives the WWVB time signal, this signal will override manually set time.

HOW LONG WILL THE BATTERY LAST?

•Two good AA Alkaline batteries will last over 24 months.

CAN I SHUT OFF THE WWVB SIGNAL?

•No. If you manually set the time, when the clock receives a WWVB signal, that signal will

override the manual set.

IS THERE A BOOSTER ANTENNA TO RECEIVE THE WWVB SIGNAL IN A

DIFFICULT LOCATION?

•No, the clock cannot work with a booster antenna.

•Opening the clock or movement voids the warranty.

CAN I WIRE A CONTROL TIMING CIRCUIT TO THE LA CROSSE TECHNOLOGY®

ATOMIC CLOCK?

•No, the clock cannot work on a timing circuit.

•Opening the clock voids the warranty.

WHY DO THE HANDS SPIN ONCE OR TWICE EVERYDAY?

•When the hands spin about the same time every day the clock is auto-correcting the

time. The hour hand should not spin more than twice around the clock.

•Hands may spin if the battery is underpowered or overpowered.

•Use only Alkaline batteries in the clock.

HANDS SPIN NON-STOP

•This is indicative of a low or overpowered battery (number 1 warranty issue).

•Replace battery and perform restart procedure. Allow 5 days to catch the WWVB signal

•If constant spinning continues, the movement may need replacement.

HANDS JUMPS OR JERKS AROUND THE DIAL

•This is indicative of a low or overpowered battery (number 1 warranty issue).

•Replace battery and perform the restart procedure. Allow up to 5 days to receive a signal.

La Crosse Technology, Ltd Page 4

•If the hands continue to jump, the movement may need replacement.

HANDS STUCK AT CERTAIN TIME

•This is indicative of a low or overpowered battery (number 1 warranty issue).

•Replace battery and perform restart procedure. Allow up to 5 days to receive a signal.

•Check to see if the hands may be bent.

•Movement may need replacement.

HANDS ARE LOOSE.

•If under warranty, the clock must be sent in for repair or the movement needs to be

replaced.

POSITION THE CLOCK

•This La Crosse Technology®atomic clock is designed for indoor or outdoor use.

•INDOOR: Select a location to place the radio-controlled clock where it will be at least six feet

away from a TV, computer, air conditioner or other household electrical appliances. The

optimal location is near a window. Windows facing Colorado provide the best signal.

•OUTDOOR: Select a location sheltered from direct sunlight and rain, preferably under a

roof or porch area, and facing Colorado for better reception of the WWVB signal.

•This clock is designed for indoor and outdoor use: but only in a dry environment and in a

temperature range between -10°F and 131°F.

Note: The clock is NOT waterproof. If left in the elements water may enter the clock and

damage it.

HOW DO I ADJUST THE TEMPERATURE OR HUMIDITY?

•With a flat tipped screwdriver, gently turn the temperature or humidity sensor screw at the

back of the clock to the desired setting.

Inhaltsverzeichnis

Andere La Crosse Technology Uhr Handbücher

La Crosse Technology

La Crosse Technology 404-1235UA-PL Bedienungsanleitung

La Crosse Technology

La Crosse Technology 513-1919 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-8117U-AL Bedienungsanleitung

La Crosse Technology

La Crosse Technology World Time Center WS-7092U Bedienungsanleitung

La Crosse Technology

La Crosse Technology WT-3181PLX1 Abmessungen

La Crosse Technology

La Crosse Technology W88631 Bedienungsanleitung

La Crosse Technology

La Crosse Technology BBB87269 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WT-8002Uv2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 102819 Bedienungsanleitung

La Crosse Technology

La Crosse Technology BBB84022 Abmessungen

La Crosse Technology

La Crosse Technology 404-3451 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WT-3144S Bedienungsanleitung

La Crosse Technology

La Crosse Technology 513-1417V2 Abmessungen

La Crosse Technology

La Crosse Technology 616-1410B Bedienungsanleitung

La Crosse Technology

La Crosse Technology WS-6002U Bedienungsanleitung

La Crosse Technology

La Crosse Technology 404-1235UA-SS Bedienungsanleitung

La Crosse Technology

La Crosse Technology WT-3132 Bedienungsanleitung

La Crosse Technology

La Crosse Technology WT-3181 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 404-1220 Bedienungsanleitung

La Crosse Technology

La Crosse Technology Radio Controlled Analog Clock WT-3181bz Bedienungsanleitung

La Crosse Technology

La Crosse Technology C86279v4 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 404-1220v2 Bedienungsanleitung

La Crosse Technology

La Crosse Technology 404-3840TX Bedienungsanleitung

La Crosse Technology

La Crosse Technology W79752 Abmessungen

Beliebte Uhr Handbücher anderer Marken

Silicon Laboratories

Silicon Laboratories SI5324 Bedienungsanleitung

Heathkit

Heathkit GC-1005 Bedienungsanleitung

Oregon Scientific

Oregon Scientific PRYSMA RMR221P Bedienungsanleitung

Andrew O'Malley

Andrew O'Malley DOTKLOK Bedienungsanleitung

ALGE-Timing

ALGE-Timing ASC3 Bedienungsanleitung

Bodet

Bodet Profil 960 Bedienungsanleitung

Nixie Clock

Nixie Clock Divergence Meter Bedienungsanleitung

Mini Gadgets

Mini Gadgets MCPro Bedienungsanleitung

Casio

Casio TMR-200 Bedienungsanleitung

Progetti

Progetti ILTEMPOSTRINGE Handbuch

BVItech

BVItech BV-101 Bedienungsanleitung

Progetti

Progetti KALIMERO Handbuch

Sharp

Sharp SPC900 Bedienungsanleitung

Datexx

Datexx DF0063 Bedienungsanleitung

LG LEC-005 Bedienungsanleitung

IKEA

IKEA ROTBLÖTA Bedienungsanleitung

U-Line

U-Line Н-2811 Bedienungsanleitung

Digiview

Digiview RC305EL Bedienungsanleitung