Lanner NCA-2512 Bedienungsanleitung

NCA-2512

User Manual

Version: 1.2

Date of Release: 2021-08-24

Network Computing

NCA-2512 User Manual

The icons are used in the manual to serve as an indication of interest topics or important messages. Below

is a description of these icons:

Note: This check mark indicates that there is a note of interest and is something that you should

pay special attention to while using the product.

Warning: This exclamation point indicates that there is a caution or warning and it is something

that could damage your property or product.

The listed websites are links to the online product information and technical support.

Resources

URL

Lanner

http://www.lannerinc.com

Product Resource

http://www.lannerinc.com/download-center

RMA

http://eRMA.lannerinc.com

In addition to contacting your distributor or sales representative, you could submit a request to our Lanner

Technical Support at http://www.lannerinc.com/technical-support where you can fill in a support ticket to

our technical support department.

to make improvements to the products described in this manual at any time without notice.

No part of this manual may be reproduced, copied, translated or transmitted in any form or by any means

without the prior written permission of the original manufacturer. Information provided in this manual is

intended to be accurate and reliable. However, the original manufacturer assumes no responsibility for its

use, nor for any infringements upon the rights of third parties that may result from such use.

Your feedback is valuable to us, as it will help us continue to provide you with more accurate and relevant

documentation. To provide any feedback, comments or to report an error, please email to

[email protected]m. Thank you for your time.

Taiwan Corporate Headquarters

Lanner Electronics Inc.

7F, No.173, Sec.2, Datong Rd.

Xizhi District, New Taipei City

22184, Taiwan

立端科技股份有限公司

221 新北市汐止區

大同路二段 173 號7樓

T: +886-2-8692-6060

F: +886-2-8692-6101

E: [email protected]m

China

Beijing L&S Lancom Platform Tech. Co., Ltd.

Guodong LOFT 9 Layer

No. 9 Huinan Road, Huilongguan Town,

Changping District, Beijing

102208 China

T: +86 010-82795600

F: +86 010-62963250

E: service@ls-china.com.cn

USA

Lanner Electronics Inc.

47790 Westinghouse Drive

Fremont, CA 94539

T: +1-855-852-6637

F: +1-510-979-0689

E: sales_us@lannerinc.com

Canada

Lanner Electronics Canada Ltd.

3160A Orlando Drive

Mississauga, ON L4V 1R5

Canada

T: +1 877-813-2132

F: +1 905-362-2369

E: sales_ca@lannerinc.com

NCA-2512 User Manual

Intel® and Atom™ are trademarks or registered trademarks of Intel Corporation or its subsidiaries in the U.S.

and/or other countries.

Intel® is a trademark of Intel Corporation or its subsidiaries in the U.S. and/or other countries.

Microsoft Windows and MS-DOS are registered trademarks of Microsoft Corp.

All other product names or trademarks are properties of their respective owners.

This product has passed the CE test for environmental specifications. Test conditions for passing included

the equipment being operated within an industrial enclosure. In order to protect the product from being

damaged by ESD (Electrostatic Discharge) and EMI leakage, we strongly recommend the use of CE-compliant

industrial enclosure products.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates, uses

and can radiate radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. The operation of this equipment in a

residential area is likely to cause harmful interference in which case the user will be required to correct the

interference at his own expense.

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant

to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful

interference when the equipment is operated in a commercial environment. This equipment generates, uses,

and can radiate radio frequency energy and, if not installed and used in accordance with the instruction

manual, may cause harmful interference to radio communications. The operation of this equipment in a

residential area is likely to cause harmful interference in which case users will be required to correct the

interference at their own expense.

Follow these guidelines to ensure general safety:

Keep the chassis area clear and dust-free during and after installation.

Do not wear loose clothing or jewelry that could get caught in the chassis. Fasten your tie or scarf and

roll up your sleeves.

Wear safety glasses if you are working under any conditions that might be hazardous to your eyes.

Do not perform any action that creates a potential hazard to people or makes the equipment unsafe.

Disconnect all power by turning off the power and unplugging the power cord before installing or

removing a chassis or working near power supplies

Do not work alone if potentially hazardous conditions exist.

Never assume that power is disconnected from a circuit; always check the circuit.

Risk of Explosion if Battery is replaced by an incorrect type. Dispose of used batteries according to the

instructions.

Installation only by a trained electrician or only by an electrically trained person who knows all English

Installation and Device Specifications which are to be applied.

Do not carry the handle of power supplies when moving to another place.

Electrical equipment generates heat. Ambient air temperature may not be adequate to cool equipment

to acceptable operating temperatures without adequate circulation. Be sure that the room in which you

choose to operate your system has adequate air circulation.

Ensure that the chassis cover is secure. The chassis design allows cooling air to circulate effectively. An

open chassis permits air leaks, which may interrupt and redirect the flow of cooling air from internal

components.

Electrostatic discharge (ESD) can damage equipment and impair electrical circuitry. ESD damage occurs

when electronic components are improperly handled and can result in complete or intermittent failures.

Be sure to follow ESD-prevention procedures when removing and replacing components to avoid these

problems.

Wear an ESD-preventive wrist strap, ensuring that it makes good skin contact. If no wrist strap is available,

ground yourself by touching the metal part of the chassis.

Periodically check the resistance value of the antistatic strap, which should be between 1 and 10

megohms (Mohms).

Environment:

Do not install and/or operate this unit in any place that flammable objects are stored or used in.

If installed in a closed or multi-unit rack assembly, the operating ambient temperature of the rack

environment may be greater than room ambient. Therefore, consideration should be given to installing

the equipment in an environment compatible with the maximum ambient temperature (Tma) specified

by the manufacturer.

Installation of the equipment (especially in a rack) should consider the ventilation of the system’s intake

(for taking chilled air) and exhaust (for emitting hot air) openings so that the amount of air flow required

NCA-2512 User Manual

for safe operation of the equipment is not compromised.

To avoid a hazardous load condition, be sure the mechanical loading is even when mounting.

Consideration should be given to the connection of the equipment to the supply circuit and the effect

that overloading of the circuits might have on over-current protection and supply wiring. Appropriate

consideration of equipment nameplate ratings should be used when addressing this concern.

Reliable earthing should be maintained. Particular attention should be given to supply connections other

than direct connections to the branch circuit (e.g. use of power strips).

Lanner Electronics Inc. shall not be held liable for any losses resulting from insufficient strength for

supporting the unit or use of inappropriate installation components.

Installation & Operation:

The installation of this product must be performed by trained specialists; otherwise, a non-specialist

might create the risk of the system’s falling to the ground or other damages.

Lanner Electronics Inc. shall not be held liable for any losses resulting from insufficient strength for

supporting the system or use of inappropriate installation components.

Suivez ces consignes pour assurer la sécurité générale :

Laissez la zone du châssis propre et sans poussière pendant et après l’installation.

Ne portez pas de vêtements amples ou de bijoux qui pourraient être pris dans le châssis. Attachez votre

cravate ou écharpe et remontez vos manches.

Portez des lunettes de sécurité pour protéger vos yeux.

N’effectuez aucune action qui pourrait créer un danger pour d’autres ou rendre l’équipement dangereux.

Coupez complètement l’alimentation en éteignant l’alimentation et en débranchant le cordon

d’alimentation avant d’installer ou de retirer un châssis ou de travailler à proximité de sources

d’alimentation.

Ne travaillez pas seul si des conditions dangereuses sont présentes.

Ne considérez jamais que l’alimentation est coupée d’un circuit, vérifiez toujours le circuit. Cet appareil

génère, utilise et émet une énergie radiofréquence et, s’il n’est pas installé et utilisé conformément aux

instructions des fournisseurs de composants sans fil, il risque de provoquer des interférences dans les

communications radio.

Risque d’explosion si la pile est remplacée par une autre d’un mauvais type.

Jetez les piles usagées conformément aux instructions.

L’installation doit être effectuée par un électricien formé ou une personne formée à l’électricité

connaissant toutes les spécifications d’installation et d’appareil du produit.

Ne transportez pas l’unité en la tenant par le câble d’alimentation lorsque vous déplacez l’appareil.

La machine ne peut être utilisée qu’à un lieu fixe comme en laboratoire, salle d’ordinateurs ou salle de

classe.

L’équipement électrique génère de la chaleur. La température ambiante peut ne pas être adéquate pour

refroidir l’équipement à une température de fonctionnement acceptable sans circulation adaptée. Vérifiez

que votre site propose une circulation d’air adéquate.

Vérifiez que le couvercle du châssis est bien fixé. La conception du châssis permet à l’air de

refroidissement de bien circuler. Un châssis ouvert laisse l’air s’échapper, ce qui peut interrompre et

rediriger le flux d’air frais destiné aux composants internes.

Les décharges électrostatiques (ESD) peuvent endommager l’équipement et gêner les circuits électriques.

Des dégâts d’ESD surviennent lorsque des composants électroniques sont mal manipulés et peuvent

causer des pannes totales ou intermittentes. Suivez les procédures de prévention d’ESD lors du retrait et

du remplacement de composants.

Portez un bracelet anti-ESD et veillez à ce qu’il soit bien au contact de la peau. Si aucun bracelet n’est

disponible, reliez votre corps àla terre en touchant la partie métallique du châssis.

Vérifiez régulièrement la valeur de résistance du bracelet antistatique, qui doit être comprise entre 1 et

10 mégohms (Mohms).

Avant d’allumer l’appareil, reliez le câble de mise à la terre de l’équipement à la terre.

Une bonne mise à la terre (connexion à la terre) est très importante pour protéger l’équipement contre

les effets néfastes du bruit externe et réduire les risques d’électrocution en cas de foudre.

Pour désinstaller l’équipement, débranchez le câble de mise à la terre après avoir éteint l’appareil.

Un câble de mise à la terre est requis et la zone reliant les sections du conducteur doit faire plus de 4

mm2 ou 10 AWG.

This equipment must be grounded. The power cord for product

should be connected to a socket-outlet with earthing connection.

NCA-2512 User Manual

Lithium Battery Caution: There is danger of explosion if the battery is incorrectly replaced. Replace

only with the same or equivalent type. Dispose of batteries according to the manufacturer's instructions.

Disposal of a BATTERY into fire or a hot oven, or mechanically crushing or cutting of a BATTERY can result

in an EXPLOSION.

Leaving a BATTERY in an extremely high temperature surrounding environment can result in an

EXPLOSION or the leakage of flammable liquid or gas.

A BATTERY subjected to extremely low air pressure may result in an EXPLOSION or the leakage of

flammable liquid or gas.

Suitable for installation in Information Technology Rooms in accordance with Article 645 of the National

Electrical Code and NFPA 75.

Peut être installé dans des salles de matériel de traitement de l'information conformément à l'article 645

National Electrical Code et à la NFPA 75.

The machine can only be used in a restricted access location, such as labs or computer facilities with the

proper authorization.

Les matériels sont destinés àêtre installés dans des EMPLACEMENTS À ACCÈS RESTREINT.

 
 
9 
 
 
 
Package Content.........................................................................................................................11 
Ordering Information .................................................................................................................12 
Optional Accessories ..................................................................................................................12 
System Specifications.................................................................................................................13 
Front Panel .................................................................................................................................14 
Rear Panel...................................................................................................................................15 
 
Block Diagram.............................................................................................................................16 
Motherboard Layout ..................................................................................................................17 
Internal Jumper & Connectors ...................................................................................................18 
 
Mounting the System .................................................................................................................24 
 
Enter BIOS Setup ........................................................................................................................30 
Main Setup .................................................................................................................................31 
Advanced Setup..........................................................................................................................32 
IntelRCSetup...............................................................................................................................50 
Security.......................................................................................................................................55 
Boot Menu..................................................................................................................................58 
Save and Exit Menu ....................................................................................................................59 
 

NCA-2512 User Manual

Warranty Policy ..........................................................................................................................66

RMA Service................................................................................................................................66

RMA Service Request Form........................................................................................................67

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Lanner Netzwerk-Hardware Handbücher

Lanner

Lanner FW-8760 Bedienungsanleitung

Lanner

Lanner LWR-X8460 Bedienungsanleitung

Lanner

Lanner uCPE NCA-4020 Bedienungsanleitung

Lanner

Lanner FW-7551 Bedienungsanleitung

Lanner

Lanner IIOT-I531 Bedienungsanleitung

Lanner

Lanner FX-3230 Bedienungsanleitung

Lanner

Lanner LEC-3340 Bedienungsanleitung

Lanner

Lanner ICS-P570 Bedienungsanleitung

Lanner

Lanner NCA-2522 Bedienungsanleitung

Lanner

Lanner NCA-5540 Bedienungsanleitung

Lanner

Lanner NCA-1010 Bedienungsanleitung

Lanner

Lanner NCA-1040 Bedienungsanleitung

Lanner

Lanner NCA-6530 Bedienungsanleitung

Lanner

Lanner NCA-4210 Bedienungsanleitung

Lanner

Lanner NCA-1513 Bedienungsanleitung

Lanner

Lanner HLM-1101 Bedienungsanleitung

Lanner

Lanner NCA-1525 Bedienungsanleitung

Lanner

Lanner HTCA-6400 Bedienungsanleitung

Lanner

Lanner FW-8771 Bedienungsanleitung

Lanner

Lanner FW-8756 Bedienungsanleitung

Lanner

Lanner NCS2-VT04 Bedienungsanleitung

Lanner

Lanner NCA-4025 Bedienungsanleitung

Lanner

Lanner FW-7580 Bedienungsanleitung

Lanner

Lanner ICS-I372 Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung

Cantek

Cantek NR310-4 Bedienungsanleitung