Lantech IPGS-5400-2P Bedienungsanleitung
IPGS-5400-2P
IGS-5400-2P
4 Modular Slots Industrial L2+ Managed (PoE) Switch w/ITU
G.8032 Ring
User Manual (Hardware)
May. 2016
Recommendation for Shielded network cables
STP cables have additional shielding material that is used to reduce external interference.
The shield also reduces the emission at any point in the path of the cable. Our
recommendation is to deploy an STP network cable in demanding electrical environments.
Examples of demanding indoor environments are where the network cable is located in
parallel with electrical mains supply cables or where large inductive loads such as motors
or contactors are in close vicinity to the camera or its cable. It is also mandatory to use an
STP cable where the power device (like IP camera) is used outdoors or where the network
cable is routed outdoors.
Important Notice
Lantech Communications Global, Inc. reserves the right to modify the
equipment, its specification or this manual without prior notice, in the interest
of improving performance, reliability, or servicing. At the time of publication
all data is correct for the operation of the equipment at the voltage and/or
temperature referred to. Performance data indicates typical values related to
the particular product.
No part of this documentation or information supplied may be divulged to any
third party without the express written consent of Lantech Communications
Global Inc. Products offered may contain software which is proprietary to
Lantech Communications Global Inc. The offer or supply of these products
and services does not include or infer any transfer of ownership.
Interference Issues
This Equipment has been tested and found to comply with the limits for a
Class A digital device, pursuant to Part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
commercial or industrial installation. This equipment generates, uses, and
can radiate radio frequency energy. It may cause harmful interference to
radio communications if the equipment is not installed and used in
accordance with the instructions.
FCC Warning
This Equipment has been tested and found to comply with the limits for a
Class-A digital device, pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates, uses, and can
radiate radio frequency energy. It may cause harmful interference to radio
communications if the equipment is not installed and used in accordance
with the instructions. However, there is no guarantee that interference will
not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct
the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
CE Mark Warning
This is a Class-A product. In a domestic environment this product may
cause radio interference in which case the user may be required to take
adequate measures.
Content
Chapter 1 Introduction.............................................5
Specification............................................................. 5
Chapter 2 Hardware Description ............................8
2.1 Physical Dimension........................................ 8
2.2 IP Protection................................................... 9
2.3 LED Indicators.............................................. 12
Chapter 3 Hardware Installation...........................13
Hardware installation ............................................. 13
3.1 Rack Mounting............................................. 14
3.2 Wiring the Power Inputs............................... 16
3.3 Wiring the Fault Alarm Contact.................... 19
3.4 Cabling......................................................... 20
3.5 USB Dongle ................................................. 23
Chapter 4 Network Application.............................24
ITU G.8032 Scheme.............................................. 24
Ring Coupling ........................................................... 24
Multiple Rings .......................................................... 25
Dual Homing ............................................................ 26
Chain....................................................................... 26
Chapter 5 Console Management ..........................28
5.1 Connecting to the Console Port................... 28
5.2 Login in the Console Interface..................... 29
5
Chapter 1 Introduction
Lantech IPGS/IGS-5400-2P is a high performance L2 + managed industrial switch which
provides L2 wire speed and advanced security function for network aggregation and
backbone deployment.
Specification
IEEE
Standards
IEEE 802.3 10Base-T Ethernet
IEEE 802.3u 100Base-TX Ethernet
IEEE 802.3ab 1000Base-TX Ethernet
IEEE 802.3z 1000Base-X Ethernet
IEEE 802.3x Flow Control Capability
ANSI/IEEE 802.3 Auto-negotiation
IEEE 802.1Q VLAN
IEEE 802.1p Class of Service
IEEE 802.1X Access Control
IEEE 802.1D Spanning Tree
IEEE 802.1w Rapid Spanning Tree
IEEE 802.1s Multiple Spanning Tree
IEEE 802.3ad Link Aggregation Control Protocol (LACP)
IEEE 802.1AB Link Layer Discovery Protocol (LLDP)
IEEE 802.1x User Authentication (Radius)
IEEE 1588 Precision Time Protocol v2
IEEE 802.3at/af PoE (IPGS-5400-2P)
Switch
Architecture
Back-plane (Switching Fabric): 56Gbps
Packet throughput ability (Full-Duplex): 71.43Mpps
@64bytes
Transfer Rate
14,880pps for Ethernet port
148,800pps for Fast Ethernet port
1,488,000pps for Gigabit Ethernet port
CPU
Marvell 800Mhz
RAM
256M Byte
6
Flash
128M Byte
MAC Address
16K MAC address table
Jumbo frame
9KB on all ports
Connectors
Max. 28 10/100/1000T RJ-45 with auto MDI/MDI-X
function
Max 28 100M Mini-GBIC : SFP sockets
Max 28 1000M Mini-GBIC : SFP sockets
RS-232 console: Female DB-9
USB for automatic backup and edited restoration
configuration
Protocol
CSMA/CD
LED
Per unit: Power 1 (Green), Power 2 (Green), Alarm
(Red) ,R.M (Green)
Link/Activity (Green), Full duplex/collision(Yellow)), MINI
GBIC (Link/Activity )(Green)
Power Supply
IGS-5400-2P: 1 built-in power + 1 optional power
IPGS-5400-2P: 1 built-in power + 1 optional power + 1 PoE
power
VAC/VDC isolated 4000V
85V~265VAC/100~370VDC
VDC isolated 1600V 36~75VDC
12V~57VDC
PoE power input 45~57VDC (55V input is
recommended for 802.3at 30W applications)(IPGS-
5400-2P)
Power
Consumption
Full load: 30W/ Unload: 13W
PoE Budget
(IPGS-5400-
2P)
Max. 720W at rear side with dual 45~57VDC input
(55V input is recommended for 802.3at 30W applications)
Relay Alarm
Provides one relay output for port breakdown, power fail
and alarm.
Alarm Relay current carry ability: 1A @ DC24V
7
DI/DO
2 Digital Input (DI) :
Level 0: -30~2V / Level 1: 10~30V
Max. input current:8mA
2 Digital Output(DO): Open collector to 40 VDC, 200mA
Case
Dimension
19” Metal case,IP-30; 440mm(W)x325mm(D)x44mm(H)
Operating
Humidity
5%~95% (Non-condensing)
Operating
Temperature
-20°C ~60°C
Storage
Temperature
-40°C ~85°C
EMI
FCC Class A, CE EN61000-4-2 (ESD),
CE EN61000-4-3 (RS), CE EN-61000-4-4 (EFT),
CE EN61000-4-5 (Surge), CE EN61000-4-6 (CS),
CE EN61000-4-8, CE EN61000-4-11,
CE EN61000-4-12, CE EN55022 Class A, CE EN55024
MTBF
245,432hrs
Stability
Testing
IEC60068-2-32 (Free fall), IEC60068-2-27 (Shock),
IEC60068-2-6 (Vibration)
Warranty
5 years
8
Chapter 2 Hardware Description
In this paragraph, it will describe the Industrial switch’s hardware spec, port, cabling
information, and wiring installation.
2.1 Physical Dimension
Metal case. IP-30,
440(W) x 325 (D) x 44 (H) mm
9
2.2 IP Protection
The IP Code, Ingress Protection Rating, sometimes also interpreted as International
Protection Rating, classifies and rates the degree of protection provided against the
intrusion (including body parts such as hands and fingers), dust, accidental contact, and
water in mechanical casings and with electrical enclosures. It is published by the
International Electrotechnical Commission (IEC)
Solid particle protection
The first digit indicates the level of protection that the enclosure provides against access
to hazardous parts (e.g., electrical conductors, moving parts) and the ingress of solid
foreign objects.
Level
Object size
protected against
Effective against
0
—
No protection against contact and ingress of objects
1
>50 mm
Any large surface of the body, such as the back of a
hand, but no protection against deliberate contact
with a body part
2
>12.5 mm
Fingers or similar objects
3
>2.5 mm
Tools, thick wires, etc.
4
>1 mm
Most wires, screws, etc.
5
Dust protected
Ingress of dust is not entirely prevented, but it must
not enter in sufficient quantity to interfere with the
satisfactory operation of the equipment; complete
protection against contact
6
Dust tight
No ingress of dust; complete protection against
contact
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere Lantech Schalten Handbücher
Lantech
Lantech IES-2008B-DNV Bedienungsanleitung
Lantech
Lantech IES-3416DSFP Bedienungsanleitung
Lantech
Lantech 5 10/100TX w/ 4 PoE Injector Industrial... Bedienungsanleitung
Lantech
Lantech LGS-2816C-RPS Bedienungsanleitung
Lantech
Lantech IPWMR-3006 Bedienungsanleitung
Lantech
Lantech IES-0208CA Bedienungsanleitung
Lantech
Lantech IPGS-0204DSFP Bedienungsanleitung
Lantech
Lantech IES-0005B Series Bedienungsanleitung
Lantech
Lantech TGS-R6616XFT Bedienungsanleitung
Lantech
Lantech mini Switch 800 Bedienungsanleitung
Lantech
Lantech IES-0008B Series Bedienungsanleitung
Lantech
Lantech IES-5408T Bedienungsanleitung
Lantech
Lantech IPES-0104FA Bedienungsanleitung
Lantech
Lantech IGC-0101DSFP Bedienungsanleitung
Lantech
Lantech IPES-5416DF Series Bedienungsanleitung
Lantech
Lantech IES-5216DF Bedienungsanleitung
Lantech
Lantech IPES/IES-5416T Series Bedienungsanleitung
Lantech
Lantech IPGS-0016 Bedienungsanleitung
Lantech
Lantech IES-2208C Bedienungsanleitung
Lantech
Lantech IPGS-0204DSFP-12V Bedienungsanleitung
