Lantronix XPort AR Kurzanleitung zur Einrichtung

Part Number 900-406

Revision H October 2011

XPort AR

Integration Guide

XPort AR Integration Guide 2

or reproduced in any form or by any means without the written permission of Lantronix.

Printed in the United States of America.

XPort is a registered trademark of Lantronix.

Ethernet is a trademark of XEROX Corporation. UNIX is a registered trademark of The Open

Group. Windows 95, Windows 98, Windows 2000, Windows NT, and Windows XP are

trademarks of Microsoft Corp. Netscape is a trademark of Netscape Communications

Corporation.

Contacts

Lantronix Corporate Headquarters

167 Technology Drive

Irvine, CA 92618, USA

Phone: 949-453-3990

Fax: 949-450-7249

Technical Support

Online: www.lantronix.com/support

Sales Offices

For a current list of our domestic and international sales offices, go to the Lantronix web site

at www.lantronix.com/about/contact.

Disclaimers

Operation of this equipment in a residential area is likely to cause interference to other

devices, in which case the user, at his or her own expense, will be required to take whatever

measures may be required to correct the interference.

Note: This product has been designed to comply with the limits for a Class B digital

device pursuant to Part 15 of FCC and EN55022:1998 Rules when properly enclosed

and grounded. These limits are designed to provide reasonable protection against

radio interference in a residential installation. This equipment generates, uses, and

can radiate radio frequency energy, and if not installed and used in accordance with

this guide, may cause interference to radio communications.

Changes or modifications to this device not explicitly approved by Lantronix will void the

user’s authority to operate this device.

The information in this guide may change without notice. The manufacturer assumes no

responsibility for any errors that may appear in this guide.

Note: With the purchase of XPort AR, the OEM agrees to an OEM firmware license

agreement that grants the OEM a non-exclusive, royalty-free firmware license to use

and distribute the binary firmware image provided, only to the extent necessary to

use the XPort AR hardware. For further details, please see the XPort AR OEM

firmware license agreement.

XPort AR Integration Guide 3

Revision History

Date

Rev.

Comments

June 2005

Initial Release

March 2007

Correct pin numbers

June 2006

Updated figure 2-7, and identified Pin 1; corrected references to

CP12 & CP13

June 2010

Minor corrections. Update company contact info.

September 2010

Minor corrections. Updated schematics under heading

“Recommended PCB Layout”.

May 2011

Updated figures 2-1, 2-6, 2-7 and 2-8.

June 2011

Updated figures 2-7 and 2-8.

October 2011

Updated security information.

For the latest revision of this product document, please check our online documentation at

www.lantronix.com/support/documentation.

XPort AR Integration Guide 4

Contents

Contacts ______________________________________________________________ 2

Disclaimers ____________________________________________________________ 2

Revision History ________________________________________________________ 3

List of Figures __________________________________________________________ 5

List of Tables___________________________________________________________ 6

1: Introduction 7

About the Integration Guide _______________________________________________ 7

Additional Documentation_________________________________________________ 7

2: Description and Specifications 8

The XPort AR __________________________________________________________ 8

XPort AR Block Diagram__________________________________________________ 9

PCB Interface __________________________________________________________ 9

Standard Pins (Evaluation Board XP300200K-01) __________________________ 9

PoE Pins__________________________________________________________ 10

Ethernet Interface ______________________________________________________ 11

Reset________________________________________________________________ 11

LEDs ________________________________________________________________ 11

Dimensions ___________________________________________________________ 12

Recommended PCB Layout ______________________________________________ 14

XPort Compatibility__________________________________________________ 14

Product Information Label________________________________________________ 15

Technical Specifications _________________________________________________ 16

3: Evaluation Kit 17

Contents of the Kit______________________________________________________ 17

Evaluation Board Description _____________________________________________ 17

Major Features _____________________________________________________ 17

Evaluation Board Major Components_______________________________________ 18

Major Components __________________________________________________ 19

XPort AR _____________________________________________________________ 19

Power Switch _________________________________________________________ 19

Reset Switch__________________________________________________________ 19

Headers______________________________________________________________ 19

JP1: Signal Access Header ___________________________________________ 19

JP2: LED Header ___________________________________________________ 20

JP3: Input Switch Header_____________________________________________ 20

Contents

XPort AR Integration Guide 5

JP4: Pull-Up Header_________________________________________________ 21

JP5: GND Header___________________________________________________ 21

Disconnect Jumpers ____________________________________________________ 21

JP6: Disconnect Jumper Header _______________________________________ 21

JP7: Disconnect Jumper Header _______________________________________ 22

JP8: Disconnect Jumper Header _______________________________________ 22

LEDs ________________________________________________________________ 23

LED1 – LED4: Signal Monitoring LEDs __________________________________ 23

LED5 – LED8: RS-232 Activity Monitoring LEDs___________________________ 23

LED9: Power LEDs__________________________________________________ 23

Test Switches _________________________________________________________ 23

Prototyping Area _______________________________________________________ 23

RS-232 Serial Interfaces_________________________________________________ 24

PoE Socket ___________________________________________________________ 25

Ground Turret _________________________________________________________ 25

Power Supply _________________________________________________________ 25

Schematic ____________________________________________________________ 25

Board Layout__________________________________________________________ 28

Component Identification _____________________________________________ 28

A: Compliance and Warranty Information 29

Compliance Information _________________________________________________ 29

Warranty _____________________________________________________________ 29

List of Figures

Figure 2-1. Side View of the XPort AR _______________________________________ 8

Figure 2-2. XPort AR Block Diagram ________________________________________ 9

Figure 2-3. XPort AR LEDs_______________________________________________ 12

Figure 2-4. Front View___________________________________________________ 12

Figure 2-5. Bottom View _________________________________________________ 13

Figure 2-6. Side View ___________________________________________________ 13

Figure 2-7. PCB Layout (Top View) ________________________________________ 14

Figure 2-8. Hole Pattern and Mounting Dimensions (Bottom View)________________ 15

Figure 2-9. Product Label ________________________________________________ 15

Figure 3-1. Evaluation Board _____________________________________________ 18

Figure 3-2. Evaluation Board (Diagram) ____________________________________ 18

Figure 3-3. Evaluation Board Schematic ____________________________________ 26

Figure 3-4. Board Layout ________________________________________________ 28

Contents

XPort AR Integration Guide 6

List of Tables

Table 2-1. Standard Interface Signals ______________________________________ 10

Table 2-2. PoE Interface Signals __________________________________________ 10

Table 2-3. Ethernet Interface Signals ______________________________________ 11

Table 2-4. XPort AR LED Functions________________________________________ 12

Table 2-5. Technical Specifications ________________________________________ 16

Table 3-1. JP1 Connections ______________________________________________ 20

Table 3-2. JP2 Connections ______________________________________________ 20

Table 3-3. JP3 Connections ______________________________________________ 21

Table 3-4. JP4 Connections ______________________________________________ 21

Table 3-5. JP5 Connections ______________________________________________ 21

Table 3-6. JP6 Connections ______________________________________________ 22

Table 3-7. JP7 Connections ______________________________________________ 22

Table 3-8. JP8 Connections ______________________________________________ 22

Table 3-9. RS-232 Signals _______________________________________________ 24

Table 3-10. Board Components ___________________________________________ 28

XPort AR Integration Guide 7

1: Introduction

About the Integration Guide

This guide provides the information needed to test the XPort®AR device server on the XPort

AR Evaluation Board. This manual is intended for engineers responsible for integrating the

XPort AR into their product.

Additional Documentation

For supporting product documentation, or the most current version of this document, please

visit the Lantronix Web site at www.lantronix.com/support/documentation.

Document

Description

XPort AR Getting Started

Provides the steps for getting the hardware and software

up and running.

XPort AR User Guide

Provides information needed to configure, use, and

update the XPort firmware.

XPort AR Command Reference Lists and explains XPort AR command line and XML

commands.

Com Port Redirector User Guide

Provides information on using the Windows-based utility

to create a virtual com port.

XPort AR Integration Guide 8

2: Description and Specifications

The XPort AR embedded device server is a complete network-enabling solution enclosed

within an RJ45 package. This miniature device server empowers original equipment

manufacturers (OEMs) to quickly and easily go to market with networking and web page

serving capabilities built into their products.

The XPort AR

The XPort AR contains Lantronix’s own DSTni controller, with 256 Kbytes of SRAM,

16 Kbytes of boot ROM, and integrated AMD 10/100 PHY.

The XPort AR also contains the following:

New powerful operating system with additional new features.

Two full serial ports with all hardware handshaking signals (or three serial ports without

handshaking signals).

13 pins are configurable as general purpose I/O.

Supports fully compliant Power over Ethernet (PoE) designs by using PoE compliant

magnetics and passing through both the used and unused pairs.

Memory: 4 MB Flash and 1.25 MB RAM.

3.3-volt serial interface.

All I/O pins are 5V tolerant.

Ethernet magnetics.

Power supply filters.

Reset circuit.

+1.8V regulator.

Ethernet LEDs.

The XPort AR requires +3.3-volt power and is designed to operate over an industrial

temperature range (see technical data).

Figure 2-1. Side View of the XPort AR

2: Description and Specifications

XPort AR Integration Guide 9

XPort AR Block Diagram

The following drawing is a block diagram of the XPort AR showing the relationships of the

components.

Figure 2-2. XPort AR Block Diagram

PCB Interface

Standard Pins (Evaluation Board XP300200K-01)

The XPort AR has 26 electrical pins. There are 20 pins that form two rows of ten. These 20

pins form the standard interface between the XPort AR and the circuit in which it is installed.

These include dedicated serial as well as 11 programmable I/O pins (Configurable Pins, or

CPs). The other group of six pins is for PoE.

The standard signals are 3.3V CMOS logic level but are 5V tolerant. These signals are

typically connected to internal devices, such as a relays, sensors, or UARTs.For prototype

and evaluation work or applications where an external RS-232 interface is required,RS-232

transceivers are available on the XPort AR evaluation board. Optionally, disconnect them

using the jumpers provided if they are not needed.

Note: Typically, after booting up CP pins are in an unstable state for a few seconds.

However, the state of the CP pins in the XPort-AR is initially high-impedance, suitable

for an input. To use a CP pin as an output, the pin may be biased high or low with a

resistor to +V or ground so it will be "defined" as either 1 or 0 during this initial time.

2: Description and Specifications

XPort AR Integration Guide 10

Table 2-1. Standard Interface Signals

Signal Name XPort AR

Pin # Primary Functions

GND 4 Signal Ground

VCC 5 +3.3V Power In

_________

Reset 8 External Reset In

TXDA 9 Serial Data Out, Channel A

RXDA 12 Serial Data In, Channel A

CP01 13 Programmable I/O or RTSA flow control

CP02 16 Programmable I/O or DTRA flow control

CP03 17 Programmable I/O or CTSA flow control

CP04 3 Programmable I/O or DSRA flow control

CP05 7 Programmable I/O or DCDA flow control

CP06 2 Programmable I/O or TXDB flow control

CP07 10 Programmable I/O or RXDB flow control

CP08 1 Programmable I/O or RTSB flow control

CP09 6 Programmable I/O or DTRB flow control

CP10 20 Programmable I/O or CTSB flow control

CP11 19 Programmable I/O or DSRB/DCDB flow control

CP12 11 I2C clock

CP13 14 I2C data

Reserved 15 Reserved

Reserved 18 Reserved

PoE Pins

XPort AR is PoE-ready; it allows a fully compliant PoE circuit to be implemented that uses the

Ethernet signals entering the XPort AR’s RJ-45 jack. When the XPort AR’s RJ-45 jack is

connected to a PoE compliant switch, pins 21, 22, 25, and 26 pass through the necessary

Ethernet signals to allow a PoE powered-device circuit to negotiate and receive power from

the switch.

Table 2-2. PoE Interface Signals

Signal Name XPort

R Pin # Primary Functions

POE12 22 Center tap from 1 & 2

POE36 25 Center tap from 3 & 6

POE45 21 Ethernet pins 4 & 5

POE78 26 Ethernet pins 7 & 8

CHSGND 23 Chassis Ground

Andere Handbücher für XPort AR

Inhaltsverzeichnis

Andere Lantronix Netzwerk-Hardware Handbücher

Lantronix

Lantronix SISPM1040-582-LRT Bedienungsanleitung

Lantronix

Lantronix ManageLinx Bedienungsanleitung

Lantronix

Lantronix XPort AR Bedienungsanleitung

Lantronix

Lantronix SecureLinx Bedienungsanleitung

Lantronix

Lantronix XPress DR+ Bedienungsanleitung

Lantronix

Lantronix SLC8 Bedienungsanleitung

Lantronix

Lantronix XPort Bedienungsanleitung

Lantronix

Lantronix WIBOX 2100 Bedienungsanleitung

Lantronix

Lantronix xPico WiFi Bedienungsanleitung

Lantronix

Lantronix XPress DR+ Bedienungsanleitung

Lantronix

Lantronix Device Server UDS 10 Montageanleitung

Lantronix

Lantronix EDS3000PS Bedienungsanleitung

Lantronix

Lantronix PremierWave 2050 Bedienungsanleitung

Lantronix

Lantronix SLC 8000 Bedienungsanleitung

Lantronix

Lantronix XPORT PROTM 900-560 Bedienungsanleitung

Lantronix

Lantronix SecureLinx Bedienungsanleitung

Lantronix

Lantronix G520 LTE Bedienungsanleitung

Lantronix

Lantronix SLC 8000 Series Bedienungsanleitung

Lantronix

Lantronix XPress DR Bedienungsanleitung

Lantronix

Lantronix SDS1101 Bedienungsanleitung

Lantronix

Lantronix XPort AR Bedienungsanleitung

Lantronix

Lantronix x6010 Bedienungsanleitung

Lantronix

Lantronix WiBox 2100E Bedienungsanleitung

Lantronix

Lantronix Spider Bedienungsanleitung

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Arista

Arista CCA-ETM-Q12 Bedienungsanleitung