LAPIS Semiconductor ML7344 Leitfaden
ML7344, ML7406EVA
Start Guide
Issue Date: May 8, 2014
FEXL7344_7406EVA_startguide-02
ML7344, 7406EVA Start Guide
FEXL7344_7406EVA_startguide-02 i
NOTES
No copying or reproductionof this document, in part or in whole, ispermitted without the consent ofLAPIS Semiconductor Co., Ltd.
The content specified herein is subject to change for improvement without notice.
Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and
operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage
arising from any inaccuracy or misprint of such information, LAPIS Semiconductor shall bear no responsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and examples of application circuits for
the Products. LAPIS Semiconductor does not grant you, explicitlyor implicitly, any license to use or exercise intellectual property or
other rights held by LAPIS Semiconductor and other parties. LAPIS Semiconductor shall bear no responsibility whatsoever for any
dispute arising from the use of such technical information.
The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio
visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices).
The Products specified in this document are not designed to be radiation tolerant.
While LAPIS Semiconductor always makes efforts to enhance the quality and reliability of its Products, a Product may fail or
malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury,
fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe
designs. LAPIS Semiconductor shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or
not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high
level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such
as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-controller or other safety
device). LAPIS Semiconductor shall bear no responsibility in any way for use of any of the Products for the above special purposes.
If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign
Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law.
Copyright 2013 - 2014 LAPIS Semiconductor Co., Ltd.
ML7344, 7406EVA Start Guide
FEXL7344_7406EVA_startguide-02 ii
Introduction
Thank you very much for purchasing products of our company. Before using this product, please use correctly after
reading this “start guide”. Moreover, please keep it carefully even after reading this. This start guide indicates enclosure
attachment ant the connection method.
The manual shown in the following other than this document is prepared. Please check if needed.
Datasheet
Design Guide
Simple MAC User’s Manual
ML7344, 7406EVA Start Guide
FEXL7344_7406EVA_startguide-02 1
1. Attention on the handling of this product
This product is evaluation kit. It is available for evaluation only.
Any responsibility cannot be taken about building this product into other products.
Please use the application software of this product with the PC with which Japanese version Windows XP is
installed.
It will become infringement of copyright, if all or apart of software of this product is reproduced without
permission of copyright or duplicate things are distributed.
Any responsibility cannot be taken about reconstruction and illegal use of this product.
If the example of a harmful electric wave interference should occur from this product, please change
operating frequency promptly, or suspend the output of an electric wave, and perform disposal for
interference evasion etc.
2. Setup Flow
Please check when open the box and all the following articles are assembled first. If it should run short or should have
damaged, please inform a purchasing agency.
CD-ROM is packed only when first time purchase.
By shipment time, mounting parts etc may differ from a photograph in part.
Please prepare a stabilized power supply, a RS-232C cable (straight), and serial communication software
(TeraTerm).
- ML7344/ML7406 Evaluation Board… 1 - ML7344, ML7406 Control Board… 1
- Power Supply Cable… 1
- CD-ROM… 1 (First time purchase only)
ML7344, 7406EVA Start Guide
FEXL7344_7406EVA_startguide-02 2
2.1. Control Board Setting
This section describes the control board setting.
Figure 1: Control Board Overview
Table 1: Detailed Description of Control Board
Number Symbol Function
SW1 In case of CN14 short,
SW1 switch is set to CN13 side (lower side in Fig.16) : set CPU reset
SW1 switch is set to “SW1” silk (upper side in Fig.16) : release CPU reset
CN14 Connect RESET pin of ML610Q482 and SW1
CN9 Short CN9 in case of the external 5.0V power supply.
CN10 If 3.0V voltage supplied by the external power supply. Please usually use open.
CN13
Change voltage supplied line on control board.
1-2 short (right side in Fig.16) : connect voltage supplied line to evaluation board.
Please usually use it in this setting.
2-3 short (left side in Fig.16) : connect voltage supplied line to CN8 (μEASE)
Open : voltage supplied by CN2 or CN8
CN3 – CN7 RS232-C interfaces are set.
ML7344, 7406EVA Start Guide
FEXL7344_7406EVA_startguide-02 3
2.2. ML7344, ML7406 Evaluation Board Setting Procedure
The ML7344 evaluation board is connected with the control board as shown below.
Figure 2: ML7344 Evaluation Board Connection Overview
The ML7406 evaluation board is connected with the control board as shown below.
Figure 3: ML7406 Evaluation Board Connection Overview
* When you do not use DIVERSITY, please use ANT1.
Connect by 26pin connecter
Supply 3.3V power
SW1 Reset Switch
Supply 3.3V power
Connect by 26pin connecter
SW1 Reset Switch
ANT2
ANT1
ML7344, 7406EVA Start Guide
FEXL7344_7406EVA_startguide-02 4
ML7344 and ML7406 evaluation board jumper function and recommended setting are as following.
Table 2: Evaluation board jumper setting table
JP No. Silk Jumper Setting Remarks
JP1 RESETN_MCU short For micro controller
JP2 REGPDIN_MCU short For micro controller
1-2short TCXO internal power supply
(3.3V)
JP3 REGVCC 2-3short TCXO external power supply
(REG_VCC)
JP4 32k_VCC open
JP5 EXT_CLK open
JP101 RESETN_TEST open For test in Lapis
JP102 REGPDIN_TEST open For test in Lapis
JP103 REGPDIN_PD open
JP104 RESETN_PU open
short Micro controller internal power supply
(3.3V)
JP105 MCU_VDD open Micro controller external power supply
(AC connecter on micro controller board)
JP106 VDDIO short ML7344’s board uses 0 Ohm.
JP107 VDD_REG short ML7344’s board uses 0 Ohm.
JP108 REG_CORE open
JP109 VDD15 open
JP110 VDD_CP short ML7344’s board uses 0 Ohm.
JP111 REG_OUT short ML7344’s board uses 0 Ohm.
JP112 VDD_VCO short ML7344’s board uses 0 Ohm.
JP113 VDD_RF short ML7344’s board uses 0 Ohm.
JP114 VDD_PA short ML7344’s board uses 0 Ohm.
JP115 REG_PA1 short ML7344’s board uses 0 Ohm.
JP116 REG_PA2 open
JP117 TEMP open
short(ML7344)
JP118 VTUNE open(ML7406)
ML7344, 7406EVA Start Guide
FEXL7344_7406EVA_startguide-02 5
2.3. Terminal Setting
2.3.1. Tera Term Setting
The Tera Term serial port settings are shown below.
The red frame indicates required settings. Use Tera Term version 4.63 or higher.
Figure 4: Tera Term Serial Port Setting Screen
Figure 5: Tera Term Terminal Setting Screen
ML7344, 7406EVA Start Guide
FEXL7344_7406EVA_startguide-02 6
2.3.2. Wireless Control Tool Setting
Wireless Control Tool (WCT) is able to control ML7344, ML7406 Simple MAC. WCT serial port setting
is below. You must set category in red box.
Figure 6: WCT serial port setting
If you push OK button on WCT serial port setting window, WCT main window is popd up. You can set
verification command in Init tab, Contro tab, RFTest tab, RegBANK0 tab, RegBANK1 tab, RegBANK2
tab or RegBANK3 tab. Please refer to “ML7344, ML7406 Wireless Control Tool User’s manual”.
Figure 7: WCT main window
Andere Handbücher für ML7344
2
Dieses Handbuch passt für folgende Modelle
1
Inhaltsverzeichnis
Andere LAPIS Semiconductor Transceiver Handbücher
