Larson Electronics EPL-LED-150W-RT-DIMM Bedienungsanleitung

EPL-LED-150W-RT-DIMM

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

1of 5

150W Explosion Proof LED Flood Light

Surface Mount - 21000 Lumens - C1D1 - 0-10V Dimmable

Instruction Manual

Thank you for your purchase of the Larson Electronics EPL-LED-150W-RT-DIMM.

WARNING:

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

CRITICAL SAFETY INSTRUCTIONS:

•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY

RELEVANT LOCAL BUILDING CODES.

•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL

SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.

•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.

•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.

•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP

OBJECTS. SUITABLE FOR DAMP LOCATIONS.

IMPORTANT

READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE

REFERENCE. THE EPL-LED-150W-RT-DIMM MUST BE WIRED IN ACCORDANCE WITH NATIONAL ELECTRICAL

CODE AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.

WE STRONGLY ENCOURAGE ONLY ALICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS

PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,

CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.

WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE

INSTALLATION OR PERFORMING ANY MAINTENANCE.

RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.

RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOT INSTALLED PROPERLY.

RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.

WARNING:

USER SHOULD BE TRAINED IN THE PROPER USE AND MAINTENANCE OF THIS DEVICE. THIS LINE

CORD IS INTENDED TO ALLOW OPERATORS TO EXTEND POWER TO EQUIPMENT WHEN STATIONARY OUTLETS ARE NOT

READILY AVAILABLE.

IMPROPER USE OF THIS CORD, PLUG, AND RECEPTACLE CAN LEAD TO SERIOUS INJURIES OR DEATH TO

PERSONNEL.

PERIODIC INSPECTION OF THE CORD IS NECESSARY.

THE CORD MUST BE ROUTINELY CHECKED FOR CUTS, BREAKS, OR ANY SEVERE ABRASIONS, AND IF ANY ARE FOUND,

THE CORD MUST BE REPLACED BEFORE RESUMING USE.

EPL-LED-150W-RT-DIMM

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

2of 5

WARNING

TO AVOIDTHE RISKOF FIRE,EXPLOSION OR ELECTRIC SHOCK, THIS PRODUCT SHOULD BE INSTALLED,

INSPECTEDAND MAINTAINEDBY A QUALIFIED ELECTRICIANONLY, IN ACCORDANCEWITHALL

APPLICABLEELECTRICAL CODES.

TO AVOIDELECTRIC SHOCK:

•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.

•PRODUCT MUST BE CONNECTED TO A WIRING SYSTEM WITH AN EQUIPMENT-GROUNDING

CONDUCTOR.

TO AVOID EXPLOSION:

•MAKE SURE THE SUPPLY VOLTAGE IS WITHIN THE VOLTAGE RATING.

•ENSURE THE MARKED T RATING IS LESS THAN THE IGNITION TEMPERATURE OF THE HAZARDOUS

ATMOSPHERE.

•DO NOT OPERATE IN AMBIENT TEMPERATURES ABOVE THOSE INDICATED ON THE PRODUCT

NAMEPLATE.

•DO NOT OPERATE IF THE LENS, CORD, SEALS, HOUSING, RECEPTACLES, ETC. IS CRACKED OR

DAMAGED. IF SO, DISCONTINUE USE AND CONTACT MANUFACTURER FOR REPLACEMENT PARTS.

•ALL FASTENERS SHOULD BE PROPERLY SEATED.

The EPL-LED-150W-RT-DIMM from Larson Electronics is an Explosion Proof High Bay Dimmable LED Light Fixture

provides operators with a powerful and energy efficient alternative to traditional hazardous location luminaries. Cree LED

technology and compact design makes this lamp an excellent replacement upgrade option for bulky and high maintenance

cost older incandescent, metal halide and high pressure sodium lights.

WIRING

Standard pigtail(flying leads) wiring

We strongly encourage a licensed electrician install this product,in all locations especially in outdoor areas

where weatherproofing may be required. Universal voltage driver permits operation at 100V - 277V AC, 50 or 60Hz

except those factory ordered with low voltage 11V to 25V AC/DC.

Low Voltage DC

Connect power to power supply outputting low voltage between 11-25 Volts DC.

This variable voltage allows greater versatility without affecting light output. Ensure

deutsch connectors are properly connected (If applicable)

For supplyconnections, use wire rated for at least 110°C

Recommendedmounting height is 25-40 feet.

MOUNTING

The EPL-LED-150W-RT-DIMM comes standard with an adjustable surface mount bracket. The EPL-

LED-150W-RT-DIMM offers an adjustable mounting system that this fixture to be mounted to any flat

surface including walls and ceilings.

Check toensure that all mounting hardware is included.

•2 Small Brackets

•1 Large Trunnion Bracket

•8 Bolts

•8 Lock-Washers

•4 Nuts

Low Voltage DC

This explosion proof LED light is universal voltage capable and can be operated with 100-277V AC, 50/60 Hz without

modifications to the fixture. A low voltage version of this LED fixture that operates on AC/DC voltages from 11-25 volts is also

available. 18-48V AC/DC voltage models are available for network systems and marine vessels. We also offer an additional

347-480V high voltage, 125-250V DC, and 0-10V dimmable versions of this explosion proof LED light fixture.

EPL-LED-150W-RT-DIMM

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

3of 5

1. Using four bolts, washers and the four nuts provided, attach brackets “A” to both sides of

bracket “B”.

2. The LED fixture has 9 holes for a versatile mount option. Select the holes that you would like to

use.

3. Brackets “A” will then be bolted to the LED fixture with the remaining bolts and washers.

4. The fixture is now ready for installation.

See Images Below as a Reference

EPL-LED-150W-RT-DIMM

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

4of 5

WIRING (see attached wiring diagram)

This unit comes preconfigured in selected voltage and beam configuration. Wire light tothe correct

voltage. Follow all applicable local, state, and National Electrical Code for the hazardous area.

Wire size is 18/5.

Voltage: Check product label for correct voltage.

Use only 0-10V Dimmer appropriate for the location installed.

WARNING: Mis-wiring Low Voltage Dimming Control could cause permanent damage to light.

DO NOT connect dimming control to line voltage.

DO NOT connect dimmer with power applied.

WIRE(AC) WIRE(DC) COLORED CABLE

AC LIVE

DC LIVE BLACK

AC NEUTRAL DCNEUTRAL WHITE

GROUND GROUND GREEN

DIMMING + DIMMING + RED

DIMMING - DIMMING - ORANGE

WARNING: CHECK NAMEPLATE FOR PROPER VOLTAGE.

DAMAGE FROM IMPROPER VOLTAGE WILL VOID WARRANTY.

EPL-LED-150W-RT-DIMM

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

5of 5

MAINTENANCE

Caution: To avoid personal injury, disconnect power to the light and allow the unit to cool down before

performing maintenance.

Warning: No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens will void

the warranty.

1. Perform visual, mechanical and electrical inspections on a regular basis. We recommend routine

checks to be made on a yearly basis. Frequency of use and environment should determine this. It is

recommended to follow an Electrical Preventive Maintenance Program as described in NFPA 70B:

Recommended practice for Electrical Equipment.

2. The lens should be cleaned periodically as needed to ensure continued photometric performance.

Clean the lens with a damp, non-abrasive, lint-free cloth. If not sufficient, use mild soap or a liquid

cleaner.

3. Inspect the cooling fins on the luminaire to ensure that they are free of any obstructions or

contamination (i.e. excessive dust build-up). Clean with a non-abrasive cloth if needed.

4. Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.

USE AND CARE

Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.

Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of

children when not in use.Inspect for good working condition prior to storage and before re-use.

REPLACEMENT PARTS

The EPL-LED-150W-RT-DIMM is designed to provide years of reliable performance. Should the need for replacement

parts arise, please contact Larson Electronics.

THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.

SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT

SALES@LARSONELECTRONICS.COM OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.

PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.

Inhaltsverzeichnis

Andere Larson Electronics Scheinwerfer Handbücher

Larson Electronics

Larson Electronics BL24-LED Bedienungsanleitung

Larson Electronics

Larson Electronics EPLC2-LED-150W-RT-JB2-50C Bedienungsanleitung

Larson Electronics

Larson Electronics EPLC2-WPLED-50W-RT Bedienungsanleitung

Larson Electronics

Larson Electronics EPLC2-LED-150W-RT-DIMM Bedienungsanleitung

Larson Electronics

Larson Electronics RCL200-RF Bedienungsanleitung

Larson Electronics

Larson Electronics WAL-QP-4X500-25 Bedienungsanleitung

Larson Electronics

Larson Electronics HID-22-SL-480V Bedienungsanleitung

Larson Electronics

Larson Electronics WAL-QP-2X-25 Bedienungsanleitung

Larson Electronics

Larson Electronics HAL-PRM-150W-LED Bedienungsanleitung

Larson Electronics

Larson Electronics GL-2151-6IN Handbuch

Larson Electronics

Larson Electronics LEDWP-LP-450-TRN-DCM Bedienungsanleitung

Larson Electronics

Larson Electronics RL-16-LED-M Bedienungsanleitung

Larson Electronics

Larson Electronics GLR-FLK-2 Bedienungsanleitung

Larson Electronics

Larson Electronics LEDWP-600E-SSB-1227-56K Bedienungsanleitung

Larson Electronics

Larson Electronics GL-4600 Handbuch

Larson Electronics

Larson Electronics WAL-M-3X48LED-120 Bedienungsanleitung

Larson Electronics

Larson Electronics HAL-TRN Series Bedienungsanleitung

Larson Electronics

Larson Electronics HAL-LED-174W Bedienungsanleitung

Larson Electronics

Larson Electronics EPLC2-LED-150W-RT-JB2 Bedienungsanleitung

Larson Electronics

Larson Electronics GL-4600-F-M-12I Handbuch

Larson Electronics

Larson Electronics LEDWP-600E-M Bedienungsanleitung

Larson Electronics

Larson Electronics HID-22-SL-3M-GAP Bedienungsanleitung

Larson Electronics

Larson Electronics Golight RadioRay 7901 Handbuch

Larson Electronics

Larson Electronics EPL-WPLED-150W-RT-140DB Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

BEGA

BEGA 85 143 Bedienungsanleitung

Beamz

Beamz 151.226 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung