Larson Electronics EXP-EMG-EXT-LE6-4L Bedienungsanleitung

EXP-EMG-EXT-LE6-4L

Explosion Proof Bug Eye Emergency LED

Fixture Instruction Manual

Congratulations on the purchase of your new Explosion Proof Bug

Eye Emergency LED Exit Fixture. Please read these instructions

carefully to familiarize yourself with the safe operation and

maintenance of your new emergency fixture. Following these

instructions will insure many years of safe and dependable service.

Table of Contents

Installation & Operation 2

I.I

Installation 2

II. Trouble-Shooting & Maintenance 3

II.I

Trouble Shooting 3

II.II

Maintenance

III.

Safety Warnings & Ratings 4

III.I

Warnings

III.II

Ratings 4

**Please visit our website for all warranty/return related questions.

II Operation

Return to Table of Contents

I. Installation & Operation

NOTE: The EXP-EMG-EXT-LE6-4L is designed to be surface mounted to flat surfaces such

as walls.

Installation

Mounting for this fixture is achieved via

mounting tabs located on the back side

of the light.

The EXP-EMG-2L-LE6 explosion proof

emergency self-testing LED fixture is NOT

a factory sealed fixture. Operators will bring

their own rigid conduit to a junction box and

complete their connects. Cap off any hubs

that are not in use.

Both battery legs must be connected

together. This prevents the battery from

draining during storage and transit. DO

NOT CONNECT HIGH VOLTAGE TO

BATTERYLEGS.

II.

Operation

ApplyAC power to the light. The LED

indicator will turn RED.

See wires labeled for connections.

Use appropriate methods for wiring

within hazardous areas following all

appropriate NEC codes. Consult an

electrician if unsure.

In the event of power loss, the fixture

will illuminate all lights automatically.

Once power is restored, the lights

will turn off and the batteries will

charge.

Mounting Tabs

on each box

Mounting Tabs

AC LIVE (120V) BLACK

AC LIVE (277V) RED

AC NEUTRAL WHITE

GROUND GREEN

Return to Table of Contents

II. Trouble-Shooting and Maintenance

CAUTION: Always turn AC power to the equipment OFF before servicing. Servicing should be

performed only by a qualified service technician.

Trouble-Shooting

Problem:Emergencylightsdonot operate.

If the charge indicator light is OFF, check

that the circuit breaker for AC supply is ON.

If the charge indicator light is OFF, check

that they battery is properly connected. If the

problem persists, replace the battery.

Problem: Emergency lights are dim.

The battery might not be fully charged.Allow

battery to recharge for 24 hours and then

retest. If the lights are still dim, replace the

battery.

II.

Maintenance

1. Battery: The battery supplied in the fixture

requires no maintenance. However, it should

be tested periodically and replaced when it

no longer operates the connected fixtures

for the duration of a 30-second or 90-minute

test.

2. Other: Clean lenses and replace lamps as

and when required.

Charger/Battery Fault

LEDs

Return to Table of Contents

II I. Safety Warnings and Ratings

Warnings

WARNING: Risk of electric shock -never

connect to, disconnect from or service while

equipment is energized.

WARNING: Risk of fire -Lamps are hot.

Keep combustible material away from the

hot parts. Observe lamp manufacturer’s

warnings, recommendations and restrictions

on lamp operation and maintenance. Make

sure lamps are correctly installed.

The battery in this emergency fixture may

not be fully charged. After electricity is

connected, let the battery charge for at least

24 hours.

Consult local building code for approved

wiring and installation.

Disconnect AC power before servicing and

installation.

DO NOT use this electrical equipment for

anything other than its intended use.

The use of accessory equipment is not

recommended by the manufacturer and will

void product listing and warranty and may

cause unsafe conditions.

Any service on this equipment should be

performed by qualified personnel only.

Cap unused wires with enclosed wire nuts or

other approved method.

Make sure wire terminations are secure and

leads are properly tucked in appropriate wire

channels.

II.

Ratings/Approvals

Class I, Divisions 1 & 2 GroupsA, B, C, D

Class I, Zones 1 & 2 Groups IIB + H2

Class II, Divisions 1 & 2 Groups E, F, G

Class III, Divisions 1 & 2

90 Minute Emergency Runtime

24 Hour Battery Recharge Time

Self-Testing Unit

Horizontal and Vertical Adjustable

EXP-EMG-EXT-LE6-4L

Explosion Proof Remote LED Light Head

Instruction Manual

Do not attempt installation until you are familiar with all warnings, precautions, and procedures outlined within

this instruction sheet.

WARNING:

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE

REFERENCE. CRITICAL SAFETY INSTRUCTIONS:

•To avoid the risk of fire, explosion, or electric shock, this product should be installed, inspected, and

maintained by a qualified electrician only, in accordance with all applicable electrical codes.

To avoid electric shock:

•Be certain electrical power is OFF before and during installation and maintenance.

•Luminaire must be supplied by a wiring system with an equipment grounding conductor.

To avoid burning hands:

•Make sure lens and housing are cool when performing maintenance.

To avoid explosion:

•Make sure the supply voltage is the same as the luminaire voltage.

•Do not install where the marked operating temperatures exceed the ignition temperature of the

hazardous atmosphere.

•Do not operate in ambient temperatures above those indicated on the luminaire nameplate.

•Use proper supply wiring as specified on the luminaire nameplate.

•All gasket seals must be clean.

•Before opening, electrical power to the luminaire must be turned off. Keep tightly closed when in

operation.

•Use only UL listed components suitable for Class I Division 1, Groups C & D and Class II Division 1,

Groups F & G installation.

•All threaded connections must engage five full threads.

Refer to the luminaire nameplate for specific

classification information, maximum ambient

temperature suitability, and corresponding

operating temperature (TCode).

MOUNTING & WIRING

1. Mount the enclosure to surface in a location

that can support the load. Use single bolt to

provide rotation when mounting.

2. Loosen the two set screws on the bracket to

adjust vertical position as necessary.

WIRING

1. Remove the front cover module by

loosening the single set screw and rotating

counter-clockwise.

2. Pull field wiring into module. This light

connects to the corresponding wires on the

main unit.

3. Close all unused conduit entries with

conduit plugs. To ensure water-tightness,

lubricate conduit plugs with lubricant before

installing, and secure wrench-tight with at

least five (5) full threads engaged (42-52 ft.-

lb. for 3/4” plugs, and 58-68 ft.-lb. for 1”

plugs).

4. Connect supply wires to luminaire wire

leads (or terminal blocks) using methods

that comply with all applicable codes.

Tighten all electrical connections.

5. Close cover module, making sure that all

wires are safely inside driver. Tighten

captive closing screw.

6. Turn power on and aim light.

Voltage: 12V DC

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com 5

EXP-EMG-EXT-LE6-4L

MAINTENANCE

1. Perform visual, electrical, and mechanical inspections on a regular basis. The environment and

frequency of use should determine this. However, it is recommended that checks be made at least

once a year. We recommend an Electrical Preventive Maintenance Program as described in the

National Fire

2. Protection Association Bulletin NFPA No. 70B: Recommended Practice For Electrical Equipment

Maintenance (www.nfpa.org).

3. The lens should be cleaned periodically to ensure continued lighting performance. To clean, wipe the

lens with a clean, damp cloth. If this is not sufficient, use a mild soap or a liquid cleaner such as

Collinite NCF or Duco #7. Do not use an abrasive, strong alkaline, or acid cleaner. Damage may result.

4. Visually check for undue heating evidenced by discoloration of wires or other components, damaged

parts, or leakage evidenced by water or corrosion in the interior. Replace all worn, damaged, or

malfunctioning components, and clean gasket seals before putting the luminaire back into service.

5. Electrically check to make sure that all connections are clean and tight.

6. Mechanically check that all parts are properly assembled.

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com 6

INSTALLATION, OPERATION & MAINTENANCE DATA SHEET

TYPE "EYS" HORIZONTAL / VERTICAL SEALING FITTING

SUITABLE FOR CLASS I, DIV. 1 & 2, GROUPS A, B, C & D

AND CLASS II, DIV. 1 & 2, GROUPS E, F & G HAZARDOUS LOCATIONS.

Sealing fittings are installed in conduit runs to minimize the passage of gases, vapors, or flames from one portion of the electrical

installation to another through the conduit, as well as to prevent precompression or "pressure-piling" of vapors or gases in conduit systems.

NOTE: Seals should be made only by experienced, careful persons in strict compliance with these instructions. Even slight variations can

cause serious field problems. Read directions completely.

DIRECTIONS FOR INSTALLATION

Using the drawings and chart at the right as a guide, install the sealing

fitting into the conduit system. Refer to the National Electrical Code,

Articles 501-5 and 502-5 for the regulations covering your specific

application.

Pull the conductors (wires) through the conduit system.

Using Packing Fiber, build a dam at each conduit hub (except upper hubs

in vertical seals.) Use a wooden stick to force the wires apart, and pack

the fiber tightly around all wires. The dam must be tight and strong

enough to keep the liquid sealing compound from leaking out before it

sets up. The completed dam should be even with the conduit stop.

Use the included Sealing Compound with these fittings. The sealing

compound is mixed with water at the rate of three (3) parts of sealing

compound to one (1) part of water by volume. See chart to determine

the amount of compound required for a specific fitting. Use a clean

mixing vessel for each batch. Sprinkle the sealing compound into the

water while stirring, until a thickpaste is formed. Continue mixing for AT

LEAST THREE (3) MINUTES. The proper consistency is just fluid

enough to pour SLOWLY , like thick gravy, from an inverted container,

NOT WATERY. Do not mix more material than can be poured in 15

minutes. Discard any material that becomes too stiffto use. Never

attempt to restore workability by stirringinmore water.

After the compound is mixed, slowly pour it into the sealing fitting to the

required level. Make sure that the wires are well separated, so the

compound completely surrounds them. Pour slowly to avoid trapping air

bubbles in the compound. Immediately wipe any spilled compound from

conduits and threads, and close the fitting with the close-up plug. Make

sure the plugs are tight.

Initial set of the sealing compound will occur within thirty (30) minutes.

However, the compound requires a minimum of 8 hours above 32° F to

develop sufficient strength to withstand explosion pressures.

*NOTE: These fittings are approved for use only with Killark "SC" Sealing Compound.

CONDUIT SIZE MIN. POUR

DEPTH

APPROX. AMOUNT MIXED

COMPOUND REQ'D. (OZ.)

½" 1.0"

1.5¾"¾"

2.51"1"

5.51¼"1¼"

7.51½"1½"

10.52"2"

EXP-EMG-EXT-LE6-4L

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com 7

Wiring Diagram

WARNING: DO NOT SERVICE WHILE ENERGIZED!

RED +++ (REMOTE HEAD POSITIVE)

BLACK --- (REMOTE HEAD NEGATIVE)

RED 277VAC (HOT)

BLACK 120VAC (HOT)

WHITE (COMMON)

GREEN (GROUND)

YELLOW +++ (REMOTE HEAD POSITIVE)

PURPLE --- (REMOTE HEAD NEGATIVE)

BUG EYE

FIXTURE

REMOTE

HEAD

BATTERY

JUNCTION

BOX

CONNECT

*SEE WIRE LABELS

EXP-EMG-EXT-LE6-4L

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com 8

Inhaltsverzeichnis

Andere Larson Electronics Leuchte Handbücher

Larson Electronics

Larson Electronics EPLC2-AMB-70LED-50 Handbuch

Larson Electronics

Larson Electronics EPLC2-LB-25LED-RT Bedienungsanleitung

Larson Electronics

Larson Electronics ATEX-EPL-TL-3X10W-C Bedienungsanleitung

Larson Electronics

Larson Electronics GVP-EMG-48-2L-LED Bedienungsanleitung

Larson Electronics

Larson Electronics EPLC2-LED-400W Bedienungsanleitung

Larson Electronics

Larson Electronics HALD-24-1X100LED-DIMM Bedienungsanleitung

Larson Electronics

Larson Electronics IND-AHF-BX-UVC-R2-120V-15C Bedienungsanleitung

Larson Electronics

Larson Electronics IND-AHC-CR-12-UVC-R1-120V Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-WPLED-100W-RT Bedienungsanleitung

Larson Electronics

Larson Electronics LEDWL-STRB-RED-1227 Bedienungsanleitung

Larson Electronics

Larson Electronics GAU-HB-12L-LED-WP-WCM Bedienungsanleitung

Larson Electronics

Larson Electronics HAL-PT-LED-CPR-C-100 Bedienungsanleitung

Larson Electronics

Larson Electronics GL-3 Series Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-HB-3X150LED-RT Bedienungsanleitung

Larson Electronics

Larson Electronics EPLC2-LB-45LED-RT-WLM Bedienungsanleitung

Larson Electronics

Larson Electronics HAL-RSLED-240W Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-PM-1X30LED-120XLV-100 Handbuch

Larson Electronics

Larson Electronics EPLC-48-432 Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-HB-100LED-RT-JB2-6-EPP Bedienungsanleitung

Larson Electronics

Larson Electronics Golight Bedienungsanleitung

Larson Electronics

Larson Electronics ATEX-EHL-1123-LED-50-EPP Bedienungsanleitung

Larson Electronics

Larson Electronics EPLC2-24-50LED Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-HB-5K-LED Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-MBC-1MLED-2023 Handbuch

Beliebte Leuchte Handbücher anderer Marken

Emos

Emos CLASSIC ZY1431T Bedienungsanleitung

Westinghouse

Westinghouse Outdoor Lighting Fixture Bedienungsanleitung

Hedler

Hedler C 12 silent Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Puck: CSI Bedienungsanleitung

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Bedienungsanleitung

Lightmaxx

Lightmaxx Shaft 5R Bedienungsanleitung

Triarch

Triarch 31083 Bedienungsanleitung

Philips

Philips 32614 Series Bedienungsanleitung

IKEA

IKEA TIVED Bedienungsanleitung

Lightolier

Lightolier LP200 Bedienungsanleitung

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Bedienungsanleitung

Martin

Martin MAC 250 Krypton Bedienungsanleitung

Cooper Lighting

Cooper Lighting Halo L3232E Bedienungsanleitung

Stageline

Stageline ODW-2410RGBW Bedienungsanleitung

Light Sky

Light Sky Tornado Series Bedienungsanleitung

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Bedienungsanleitung

Lightolier

Lightolier Lytespan 83ED17S Bedienungsanleitung

Lightolier

Lightolier Calculite CS8226 Bedienungsanleitung