Larson Electronics EPL-EMG-HB-50LED-RT-WLM Bedienungsanleitung

EPL-EMG-HB-50LED-RT-WLM

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

1of 2

C1D1 Explosion Proof High Bay LED Fixture w/ Emergency Battery

Backup - Paint Spray Booth Approved

Instruction Manual

This explosion proof light is designed for illumination of industrial locations. It uses the latest in

solid state lighting technology for long life, low maintenance and high efficiency.

The unique design focuses the light where it is needed, giving improved efficiency over a

conventional HID luminaire.

This light fixture is shipped preconfigured to work in the selected voltage range. This includes 100-

277V AC 50/60hz or 11-25V AC/DC depending on model selected. An internal, universal input power-

factor-corrected switch allows it to be used from any voltage within range without variation in light

output. Check product label for correct input voltage!

WARNING

To avoid the risk of fire, explosion or electric shock, this product should be installed, inspected

and maintained by a qualified electrician only, in accordance with all applicable electrical codes.

To avoid electric shock:

Be certain electrical power is OFF before and during installation and maintenance.

Luminaire must be connected to a wiring system with an equipment-grounding conductor.

To avoid explosion:

Make sure the supply voltage is within the luminaires’ voltage rating.

Ensure the marked T rating is less than the ignition temperature of the Hazardous

Atmosphere.

Do not operate in ambient temperatures above those indicated on the luminaire nameplate.

Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.

For supply connections, use wire rated for at least 110°C

Recommended mounting height is 15-40 feet.

MOUNTING

The EPL-EMG-HB-50LED-RT-WLM offers a flat surface mounting system, mounted with four bolts

through the tabs on the wiring junction box. This mounting feature caters to wall mounting

preferences.

WIRING (see below wiring diagram)

The EPL-EMG-HB-50LED-RT-WLM explosion proof wall mount LED light fixture is equipped with 10

feet of abrasion and chemical resistant 16/3 SOOW cable with flying leads. The LED light fixture

features 5 3/4" NPT threaded ports for running conduit; four of the ports are located on the corners of

the unit and the fifth port is found on the rear of the explosion proof wall mount LED fixture. Feed

wiring through a port to complete connections.

1. (See wire diagram) Wire the “Neutral”, “Hot”, and “Ground”

wires to power source.

2. Wire White/Red to switch if applicable.

WARNING: CHECK NAMEPLATE

FOR PROPER VOLTAGE. DAMAGE

FROM IMPROPER VOLTAGE WILL

VOID WARRANTY.

EPL-EMG-HB-50LED-RT-WLM

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

2of 2

OPERATION

The emergency LED light works, mounts and is wired like our EPL-HB-50LED-RT-CM LED light

fixtures. The main differences are that we add a remote mounted battery backup unit that adds

emergency light functionality to the fixture and the EPL-EMG-HB-50LED-RT-WLM is equipped with a

wall mounting bracket. This emergency LED light will run at the standard UL suggested 90 minutes

after power is lost. The light recharges the battery once electrical power is restored. Standard

configuration includes a single emergency battery backup that is automatically recharged and kept in

a ready state.

MAINTENANCE

Caution: To avoidpersonal injury, disconnect power to the light and allow the unit to cool down

beforeperforming maintenance.

Warning:No user serviceable parts inside of fixture. Risk of electric shock. Removal of the lens

will voidthe warranty.

1. Perform visual, mechanical and electrical inspections on a regular basis. We recommend routine checks to be

made on a yearly basis. Frequency of use and environment should determine this. It is recommended to follow

an Electrical Preventive Maintenance Program as described in NFPA 70B: Recommended practice for Electrical

Equipment.

2. The lens should be cleaned periodically as needed to ensure continued photometric performance. Clean the

lens with a damp, non-abrasive, lint-free cloth. If not sufficient, use mild soap or a liquid cleaner.

3. Inspect the cooking fins on the luminaire to ensure that they are free of any obstructions or contamination

(i.e. excessive dust build-up). Clean with a non-abrasive cloth if needed.

4. Do not operate if the lens is cracked or damaged. All fasteners should be properly seated.

BACKUP BATTERY MAINTENANCE

Although no routine maintenance is required to keep the backup battery functional, it should be checked

periodically to ensure that it is working .The following schedule is recommended:

1. Test the emergency operation of the fixture at 30-day intervals for a minimum of 30 seconds by severing power

to the fixture. The lamp should operate at full illumination.

2. Conduct a 90-minute discharge test once a year. The lamp should operate at full illumination for at least 90

minutes.

!!!! REFER ANY SERVICING INDICATED BY THESE

CHECKS TO QUALIFIED PERSONNEL !!!!

THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.

SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT

SALES@LARSONELECTRONICS.COM OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.

PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.

Wiring Diagram:

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

1of 1

EYM INSTALLATION / SEALING COMPOUND

HAZARD WARNINGS: May cause irritation to eyes and skin. Inhalation dust is considered a nuisance

dust. Avoid physical contact by wearing appropriate gloves and dust goggles. If powder gets into eyes,

flood immediately for 15 minutes with water. Wash hand thoroughly with soap and water after

handling

Mix 2 parts Sealing Compound to 1 part clean

water. Mix thoroughly. Do not mix more than

can be used in 15 minutes. Use cold water as

warm water accelerates set.

Vertical Installation:

Seal fitting is installed with the small access plug in the

up position. Both access plugs are removed after

conductors are installed. Damming fiber is installed

through the lower access port into the lower portion of

the fitting body. Care must be taken to insure the fiber

fills all voids around each conductor, as well as between

conductors and the wall of the seal fitting body. Replace

the lower (large) access plug. Mix compound according

to manufacturer instructions and pour through the upper

(smaller) access port until compound reaches the base

of the access port threads. Replace remaining plug in

upper access port. Both plugs are to be made up with

five threads engaged and wrench tight.

Horizontal Installation:

Seal body is installed with both access plugs in the up

position. Both access plugs are removed after

conductors are installed. Damming fiber is installed

through the large access port into both ends of the seal

fitting body to allow sealing compound to flow to the

required thickness (Table A). Care must be taken to

insure the fiber fills all voids around each conductor, as

well as between conductors and the wall of the seal

body.

Replace the small access port plug. Mix compound

according to manufacturer instructions and pour through

the large access port until compound reaches the base

of the access port threads. Replace large plug. Both

plugs are to be made up with five threads engaged and

wrench tight.

Class I Group A & B Installations:

Vertical Installation:

Sealing compound is to be mixed at ambient

temperature above 40°f. / 4°c. and poured into fitting

with body temperature not below 40°f. / 4°c. Ambient

temperature (of fitting) must not drop below 40°f. / 4°c.

for 72 hours. Compound must cure for 72 hours before

circuits are placed into service.

Horizontal Installation:

Sealing compound is to be mixed at room temperature,

and poured into fitting at room temperature. Ambient

temperature of fitting must remain at room temperature

for 72 hours. Compound must cure for 72 hours before

circuits are placed into service.

Class I Group C & D Installations:

Sealing compound is to be mixed at ambient

temperature above 35°f. / 2°c. and poured into fitting

with body temperature not below 35°f. / 2°c. Ambient

temperature (of fitting) must not drop below 35°f. / 2°c.

for 8 hours. Compound must cure for 8 hours before

circuits are placed into service.

Dieses Handbuch passt für folgende Modelle

Andere Larson Electronics Leuchte Handbücher

Larson Electronics

Larson Electronics EPL-WPLED-100W-RT-DIMM Bedienungsanleitung

Larson Electronics

Larson Electronics EPLC2-LB-45LED-RT-WLM Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-WPLED-100W-RT Bedienungsanleitung

Larson Electronics

Larson Electronics HALP-48-2L-LED-DNMS Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-16BS-1X150LED-X24I-C1D1-200 Handbuch

Larson Electronics

Larson Electronics GVP-48-2L-LED-D-LV Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-HB-5K-LED Bedienungsanleitung

Larson Electronics

Larson Electronics Golight Bedienungsanleitung

Larson Electronics

Larson Electronics IND-HR-UVC-EXS-R1-24-3L-120V-2X Bedienungsanleitung

Larson Electronics

Larson Electronics EPLC2-LB-40LED-RT-CM Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-PM-1X30LED-100 Handbuch

Larson Electronics

Larson Electronics EPLC2-LB-25LED-RT Bedienungsanleitung

Larson Electronics

Larson Electronics RCL360-LED-40 Bedienungsanleitung

Larson Electronics

Larson Electronics HALP-96-2L-LED Bedienungsanleitung

Larson Electronics

Larson Electronics HAL-16BS-1X185LED-CPR-100 Handbuch

Larson Electronics

Larson Electronics ATEX-EPL-TL-3X10W-C Bedienungsanleitung

Larson Electronics

Larson Electronics GVP-48-2L-LED-G3 Bedienungsanleitung

Larson Electronics

Larson Electronics LED T Series Bedienungsanleitung

Larson Electronics

Larson Electronics WAL-C-4XM Bedienungsanleitung

Larson Electronics

Larson Electronics LED25WRE-LENSCOVER Bedienungsanleitung

Larson Electronics

Larson Electronics WAL-SBDL-SS-WP60E-24-1227 Bedienungsanleitung

Larson Electronics

Larson Electronics HAL-RSLED-240W Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-AMB-150LED-200 Bedienungsanleitung

Larson Electronics

Larson Electronics HALD-24-1X150LED-V3-DIMM Bedienungsanleitung

Beliebte Leuchte Handbücher anderer Marken

Emos

Emos CLASSIC ZY1431T Bedienungsanleitung

Westinghouse

Westinghouse Outdoor Lighting Fixture Bedienungsanleitung

Hedler

Hedler C 12 silent Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Puck: CSI Bedienungsanleitung

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Bedienungsanleitung

Lightmaxx

Lightmaxx Shaft 5R Bedienungsanleitung

Triarch

Triarch 31083 Bedienungsanleitung

Philips

Philips 32614 Series Bedienungsanleitung

IKEA

IKEA TIVED Bedienungsanleitung

Lightolier

Lightolier LP200 Bedienungsanleitung

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Bedienungsanleitung

Martin

Martin MAC 250 Krypton Bedienungsanleitung

Cooper Lighting

Cooper Lighting Halo L3232E Bedienungsanleitung

Stageline

Stageline ODW-2410RGBW Bedienungsanleitung

Light Sky

Light Sky Tornado Series Bedienungsanleitung

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Bedienungsanleitung

Lightolier

Lightolier Lytespan 83ED17S Bedienungsanleitung

Lightolier

Lightolier Calculite CS8226 Bedienungsanleitung