Larson Electronics RCL360-LED-40 Bedienungsanleitung

Larson Electronics LLC www.LarsonElectronics.com sales@larsonelectronics.com

9419 E US HWY 175, Kemp, TX 75143 - P: (800) 369-6671 - F: (903) 498-3364

RCL360-LED-40

INTRODUCTION

Encased in a durable hard anodized aluminum and stainless steel housing with high power LEDs and

patented optics and electronic technology, this searchlight produces concentrated, high intensity and

focus-adjustable brilliant light beams up to 3,888’. These light function under the most severe and

harsh conditions. This versatile searchlight is suitable in a wide range of applications including search,

rescue, riot control, firefighting, military, border patrol, marine, vehicles, planes, drones, airport,

seaports, transportation stations, public areas, jails, sports and any outdoor activities.

These searchlights are available in 40W and 80W models. Constant current voltage technology

optimizes power from any rechargeable battery for extended portable use and ensures light beam to

remain steady regardless of battery discharging status. For example, a 24V 26AH rechargeable battery

can power a 40W light continuously at regular intensity for up to 60 hours. This light may also be

powered directly by an optional 110/220 VAC to 12/24 VDC converter. An optional adapter cable is

available to connect these searchlights to cigarette lighter sockets of automobiles. A specially coated

telescope grade lenses project even illuminating and focus-adjustable light beams suitable for both

long distance illumination at minimum beam angle (spot mode) or near-field peripheral illumination at

a wider beam angle (flood mode).

Two groups of multiple lights can be controlled by a single handheld wireless remote control. The

controller can change the light beam angle and cycle operation modes through: Steady Light –Strobe –

SOS. The remote control can also control the panning and tilting of the light. With the pan-tilt, the

searchlight can be controlled to cover surrounding space in all hemispherical directions. The wireless

operation does not interfere with other wireless applications. IPX6 waterproof rating keeps out

moisture and dirt.

Larson Electronics LLC www.LarsonElectronics.com sales@larsonelectronics.com

9419 E US HWY 175, Kemp, TX 75143 - P: (800) 369-6671 - F: (903) 498-3364

CAUTION

Read this instruction manual before using the searchlight to avoid accidental damage to the

light. If unusual situations arise during normal use, disconnect the power source immediately

and contact the dealer for help.

These lights are maintenance free. Pay attention to the power indicator light on the remote

control. If the red indicator light beneath the “Remote Control Power Switch” starts to blink,

the built-in battery should be recharged.

The cigarette lighter adapter cable should be used with the cigarette lighter power outlet. If

generic cable is used and the power rating is not high enough, the cable may be over heated

and cause a fire.

The protective glass on this searchlight is tempered and multi-coated for higher light

transmission rate. Avoid hitting the glass with any object and keep the glass clean for better

performance.

The operating temperature of this light is between -20°C and +45°C. Pay special attention to

the normal functioning of the light when it is used in extreme high or low temperatures beyond

that range.

The magnetic mount can withstand wind speed up to 60 mph. We DO NOT recommend

operating a magnetically mounted light on any object that may move at a high speed.

STROBE WARNING

Exposure to strobe lights may cause dizziness, disorientation, and nausea. A small percentage of people

suffer from photosensitive epilepsy, and may experience seizures or blackouts triggered by strobe

lights. Anyone who has had symptoms linked to this condition should consult a doctor before using this

product.

BRIGHT LIGHT WARNING

This light has super high intensity and concentrated illuminating power and can cause short-term to

long-term eye damage if looking directly into the light. To avoid eye damage, never point the light

beam at the eyes of any person or animal.

POWERING THE LIGHT

Cigarette Lighter

Connect the waterproof connector of a cigarette lighter adapter cable (optional accessory) to the

power input socket of the light. Make sure the notch at the connector and the opening of the socket

are aligned. Turn the waterproof locking nut clockwise until the nut is tight. Plug the cigarette lighter

adapter at the other end of the cable into the cigarette lighter of an automobile.

Larson Electronics LLC www.LarsonElectronics.com sales@larsonelectronics.com

9419 E US HWY 175, Kemp, TX 75143 - P: (800) 369-6671 - F: (903) 498-3364

CAUTION: Make sure the output voltage of the cigarette lighter (12V or 24V) matches the input voltage

of the light. Some vehicles provide 12VDC output while some vehicles provide 24VDC output. Order the

light to be suitable for your vehicle. Connecting a power source of wrong voltage to the light can

damage the light permanently.

AC Adapter

Connect the waterproof connector of a cigarette lighter adapter cable to the power input socket of the

light. Make sure the notch at the connector and the opening of the socket are aligned. Turn the

waterproof locking nut clockwise until the nut is tight. Plug the AC plug of the adapter into an AC outlet

socket. Our certified AC adapter is auto-switched between 100-240 VAC power supplies.

CAUTION: Make sure the output voltage of the AC power adapter matches the input voltage of the

light. Connecting a power source of wrong voltage to the light can damage the light permanently.

DC Power Source Directly

According to your application, you may prefer connecting to a DC power supply such as a portable DC

battery or DC generator. First, cut the waterproof connector off the input cable extruding from the

base of the light. Prepare the wires for direct connection. Make sure your DC power supply is turned off

while connecting the wires. You can consider adding a switch to the DC power source circuit to turn

power to the light on/off easily. Securely connect the exposed RED wire from the pan-tilt to the

positive terminal of the connection cable from your DC power source. Securely connect the exposed

BLACK wire form the pan-tilt to the negative terminal of the connection cable from your DC power

source. Insulate the connections to avoid any electrical shortage. Turn on your DC power source to turn

on the light. CAUTION: This option must be performed by a licensed electrician. Make sure the output

voltage of the DC power source matches the input voltage of the light. Also make sure the polarities of

the connections are positive to positive and negative to negative. Connecting a wrong voltage or wrong

polarity to the light can damage the light permanently.

MOUNTING THE LIGHT

Permanent Mount on a Board

Typical application of this method is permanently mounting the light on the roof of a vehicle, a boat, a

tower, or a building. These searchlights are usually mounted in an upright position for waterproofing

and maximum tolerance to impact forces. If a highly mounted searchlight needs to illuminate the area

below, the light can be mounted upside down with an optional mounting pan. However, the tolerance

to impact forces is reduced when the light is mounted upside down. We DO NOT recommend mounting

these lights upside down due to the weight of the light. The following instructions apply to mounting

the light in the normal upright position. The electrician must plan ahead to prepare the appropriate DC

power supply and its switching to the light before applying this mounting method.

Larson Electronics LLC www.LarsonElectronics.com sales@larsonelectronics.com

9419 E US HWY 175, Kemp, TX 75143 - P: (800) 369-6671 - F: (903) 498-3364

There are four pre-drilled holes at the bottom of the pan-tilt.

1. Mark the centers of the four holes on the board according to the layout.

2. Drill four holes of appropriate diameters on the thin board.

3. Choose stainless steel metric bolts with suitable length and diameter (not provided) base on

the thickness of the board or the wall. The pre-drilled hole is M6x1x80 for the 40W and

M8x1x80 for the 80W. Stainless steel metric bolts are recommended. The chosen bolt should

be slightly shorter than or equal to the thickness of wall +80mm.

4. Tighten the bolts onto the light through the drilled holes.

CAUTION: Make sure the voltage of the power supply matches the input voltage of the light.

Connecting a power source of wrong voltage to the light can damage the light permanently. Also make

sure the chosen bolts are of proper length and specification. If bolts are too short, too long, or to small,

the light may not be secured properly.

Flat Surface with Easy Mount

Easy Mount is only available for the 40W models. There are two installation options to use the Easy

Mount (optional accessory). Four special lug bolts are shipped with an Easy Mount.

Option 1: Mount Locking Base of Easy Mount Permanently on Flat Surface

Typical application of this method is where the locking base of the standard Easy Mount is permanently

mounted on a flat surface while the light can be attached or detached quickly for security and storage

purpose. Tighten four stainless steel M6 screws of appropriate head size and length (not supplied) at

the four outer holes on the locking base of the Easy Mount onto the flat surface. The locking base will

be left in place on the flat surface permanently.

Option 2: Attach Locking Base of Easy Mount Temporarily on a Flat Surface by Magnets

Typical application of this method is where the flat surface is ferrous and suitable for magnetically

attached heavy equipment securely. The light is securely tightened on the locking base of the Easy

Mount with Magnets. There are four magnets permanently installed at the bottom of the locking base

of the Easy Mount. Refer to below instructions for mounting the light onto Easy Mount. The whole

assembly of the Easy Mount with the light securely mounted Is quickly attached to or detached from

the flat surface.

CAUTION: We do not recommend that the whole assembly is left on the surface while the underlying

object moves. We cannot warrant the safety of this mounting method because we cannot predict the

ferrous condition of the surface. This mounting method is used at customers own risk. Excessive speeds

may cause the light to fly off of the moving object. Please consider mounting the locking base

permanently as an alternative.

Larson Electronics LLC www.LarsonElectronics.com sales@larsonelectronics.com

9419 E US HWY 175, Kemp, TX 75143 - P: (800) 369-6671 - F: (903) 498-3364

Mounting Light on Easy Mount

1. Tighten the four special lug bolts into the four pre-drilled holes underneath the pan-tilt by

turning clockwise.

2. Turn knob of the locking bolt counterclockwise to loosen the movable plate of the Easy

Mount.

3. Dial lever counterclockwise to align the four holes on the movable plate to the bigger side of

the four corresponding keyholes on locking base.

4. Insert the four lug bolts underneath the pan-tilt into the aligned holes on the Easy Mount.

You may prefer to place the light so that the power input cable of the light faces the ‘back

side” of your installation. Because the light can pan in all directions, it does not really matter

which what the light is placed on the Easy Mount.

5. Dial lever clockwise to align the four holes on the movable plate to the smaller side fo the

four corresponding keyholes on locking base. Turn the knob of the locking bolt clockwise

until tight to tighten the movable plate of the Easy Mount. Make sure the light is locked in

place.

6. Connect the power to the light according to the instructions in the Connecting Power to the

Light section. The light is ready to use.

Dismounting the Light from Easy Mount

1. Disconnect power from the light.

2. Turn knob of the locking bolt counterclockwise to loosen the movable plate of the Easy Mount.

3. Dial the lever counterclockwise to align the four holes on the movable plate to the bigger side

of the four corresponding keyholes on locking base.

4. Dismount the light from the locking base of the Easy Mount. Store the light in a secure place.

Self-Reset of the Light

Whenever power to the light is turned on, the light will start a self-resetting procedure. The light will

blink once. The pan-tilt will pan and tilt the light and automatically set the light to a neutral position.

CAUTION: During the self-resetting process, DO NOT try to stop the automatic movement by force. DO

NOT use the remote control to attempt to control the light functions and DO NOT remove power to the

light. After several seconds, the light will stop and then will be ready to use.

REMOTE CONTROL

Each light comes with one wireless handheld remote control.

Larson Electronics LLC www.LarsonElectronics.com sales@larsonelectronics.com

9419 E US HWY 175, Kemp, TX 75143 - P: (800) 369-6671 - F: (903) 498-3364

Charging Remote Control

The remote control is equipped with a built-in lithium rechargeable battery. A USB charging cable is

included with each wireless remote control. When the remote control is on and the red indicator light

beneath the “Remote Control Power Switch” starts to blink, the built-in battery should be recharged.

Plug the charging cable into the “Remote Control Charging Socket” at the bottom of the remote

control. Connect the USB end into any USB power source such as a USB charger (not included) or a USB

power output from a computer (not included). A red indicator light near the bottom edge will come on.

This indicator light will become green when charging is complete. Unplug the USB cable. Charing the

remote control only when the red light starts to blink will extend the useful life of the rechargeable

battery. A rechargeable battery is usually good for about 1,000 charges.

Power ON/OFF Remote

While the remote control is off, press and hold “Remote Control Power Switch” until a green indicator

light comes on. Red lights under “Select 1st Group of Lights” and other function buttons will come on as

well. Remote control is ready to be used.

Change Light Intensity

The light has three brightness levels: High Intensity, Medium Intensity, Regular Intensity. Press

“Brighter +” button to increase the light intensity. Press “Dimmer –“ button to decrease the light

intensity or until the light is turned off.

Change Mode

Pressing the “Mode” button can cycle the light through three different modes: Steady, Strobe, and SOS.

Larson Electronics LLC www.LarsonElectronics.com sales@larsonelectronics.com

9419 E US HWY 175, Kemp, TX 75143 - P: (800) 369-6671 - F: (903) 498-3364

Use as Spot Light

Pressing the “Spot Light” button will narrow the beam angle. The light beam will be more focused and

is suitable for far illumination.

Use as Flood Light

Pressing the “Flood Light” button will widen the beam angle. The light beam will be a wider spread and

is suitable for near-field peripheral illumination.

Pan Light

Press the “Pan Clockwise” or “Pan Counterclockwise” button to rotate the light up 355° clockwise or

counterclockwise.

Tilt Light

Pressing the “Tilt Up” or “Tilt Down” button will tilt the light up or down between -30° to +180°.

Control Groups of Lights

Each remote can be programmed to control two groups of lights. Each group can include unlimited

number of lights. A light can only be assigned to one group of one remote control. Press “Select 1st

Group of Lights” button to select group one of lights. Press “Select 2nd Group of Lights” button to select

group two of lights. The two groups can be selected individually or together. When a group selection

button is on (selected), the remote control functions will apply to all of the lights included in that

group. NOTE: While a remote control can pair with many lights, a light can be paired with one Select

Group button of one remote control. Always send a light together with its paired remote control. If a

light is paired with a new remote, the old remote will not work with that light anymore.

Pair a Light with a Remote Control

Each remote control has a programming magnet on the upper left corner. There is N-Mark below the

antenna of a light. Follow the steps below to pair a light with a group of a remote control:

a) Make sure the remote control is turned off.

b) Continuously touch the programming magnet on the remote control to the N-Mark of the light.

c) Connect and turn on power to the light while holding the magnet on the N-Mark. The light will

not start the self-reset process. Instead the light will blink. Once the light blinks, the

programming magnet does not need to touch the N-Mark.

d) While pressing and holding down one of the two “Select Group of Lights” buttons, press and

hold the “Remote Control Power Switch” until a green indicator light comes on.

Larson Electronics LLC www.LarsonElectronics.com sales@larsonelectronics.com

9419 E US HWY 175, Kemp, TX 75143 - P: (800) 369-6671 - F: (903) 498-3364

e) Release the “Remote Control Power Switch” first. Release the “Select Group of Lights” button

next. The red indicator light under the chosen “Select Group of Lights” button will blink.

f) Press “Remote Control Power Switch” once. The red indicator light under the chosen “Select

Group of Lights” button will become steady.

g) Press “remote Control Power Switch” again. The light will be off and starts its self-reset

process. The programming is finished.

h) TEST SETUP: Use the remote control to operate the light with the chosen group. If the pairing

process is unsuccessful, redo Steps A-G.

Inhaltsverzeichnis

Andere Larson Electronics Leuchte Handbücher

Larson Electronics

Larson Electronics EPL-MBC-1MLED-2023 Handbuch

Larson Electronics

Larson Electronics EPLC2-24-50LED Bedienungsanleitung

Larson Electronics

Larson Electronics IND-AHC-CR-12-UVC-R1-120V Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-PM-1X30LED-100 Handbuch

Larson Electronics

Larson Electronics LEDWL-STRB-RED-1227 Bedienungsanleitung

Larson Electronics

Larson Electronics HALS-48-2L-LED Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-EMG-HB-50LED-RT-WLM Bedienungsanleitung

Larson Electronics

Larson Electronics GVP-48-2L-LED-G3 Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-LP-70W-LED-WALL Handbuch

Larson Electronics

Larson Electronics SPLT-1.59K-800A-30-4X100W-LED-MS Bedienungsanleitung

Larson Electronics

Larson Electronics ATEX-EHL-1123-LED-50-EPP Bedienungsanleitung

Larson Electronics

Larson Electronics EPLC2-LB-25LED-RT Bedienungsanleitung

Larson Electronics

Larson Electronics HALP-48-2L-LED-DNMS Bedienungsanleitung

Larson Electronics

Larson Electronics HALP-96-2L-LED Bedienungsanleitung

Larson Electronics

Larson Electronics EPLC2-WPLED-100W-RT Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-HB-50LED-RT-SP0122 Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-AMB-150LED-200 Bedienungsanleitung

Larson Electronics

Larson Electronics EPLC-48-432 Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-HB-100LED-RT-JB2-6-EPP Bedienungsanleitung

Larson Electronics

Larson Electronics LEDWP-600E-E2E-10C Bedienungsanleitung

Larson Electronics

Larson Electronics ATEX-EPL-TL-3X10W-C Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-AMB-150LED-250 Bedienungsanleitung

Larson Electronics

Larson Electronics EPLC2-LB-45LED-RT-WLM Bedienungsanleitung

Larson Electronics

Larson Electronics Golight Bedienungsanleitung

Beliebte Leuchte Handbücher anderer Marken

Emos

Emos CLASSIC ZY1431T Bedienungsanleitung

Westinghouse

Westinghouse Outdoor Lighting Fixture Bedienungsanleitung

Hedler

Hedler C 12 silent Bedienungsanleitung

Blizzard Lighting

Blizzard Lighting Puck: CSI Bedienungsanleitung

Energetic Lighting

Energetic Lighting ELYSL-5004 Series Bedienungsanleitung

Lightmaxx

Lightmaxx Shaft 5R Bedienungsanleitung

Triarch

Triarch 31083 Bedienungsanleitung

Philips

Philips 32614 Series Bedienungsanleitung

IKEA

IKEA TIVED Bedienungsanleitung

Lightolier

Lightolier LP200 Bedienungsanleitung

Chauvet Professional

Chauvet Professional ROGUE R1 BEAM WASH Bedienungsanleitung

Martin

Martin MAC 250 Krypton Bedienungsanleitung

Cooper Lighting

Cooper Lighting Halo L3232E Bedienungsanleitung

Stageline

Stageline ODW-2410RGBW Bedienungsanleitung

Light Sky

Light Sky Tornado Series Bedienungsanleitung

Lightolier

Lightolier Paralyte 2424 PLA2G9LS26U Bedienungsanleitung

Lightolier

Lightolier Lytespan 83ED17S Bedienungsanleitung

Lightolier

Lightolier Calculite CS8226 Bedienungsanleitung