Larson Electronics HID-X970-SA Bedienungsanleitung

Larson Electronics LLC WWW.MAGNALIGHT.COM

9419 E US HWY 75, Kemp, TX 75143 - P: 903-498-3363 F: 903-498-3364 E: sales@magnalight.com

HID-X970-SA

H.I.D. SYSTEM WARNING

Do not stare directly into the light or shine directly into the eyes of another person as this may

cause temporary loss of vision.

Do not let water enter the case, while the light is both weather and water resistant, it is not

designed to be submersible.

Never disassemble the light as all parts must be factory serviced to insure proper operation.

The auxiliary light is to be mounted on the vehicle only in a vertical, bottom-mounting or in a

suspended position.

Do not allow objects or skin to contact a hot lens because of burn risk.

The auxiliary light must not adversely affect the performance of low beam, high beam, engine

cooling or the driver’s view.

Before working on the auxiliary Xenon light: disconnect the negative terminal (-) from the

battery. Make sure that the vehicle’s electrical system is de-energized.

Installation and lamp change may only be carried out by qualified or properly trained persons.

Use the supplied wire harness for electrical installation.

Before switching on the auxiliary light, the lens cover must be removed!

NOTICE

Completely read all instructions before installing.

Consult your local or state regulatory agency regarding the use of auxiliary lighting.

The placement of auxiliary lighting should not restrict airflow to the radiator or block

headlamps, turn signals or parking lights.

INSTALLING THE LIGHT

1. Disconnect the negative terminal (-) from the battery and wrap with electrical tape to prevent

contact.

2. Select a suitable attachment location and then mark and drill the 11 mm diameter hole for

mounting.

CAUTION: Consult your vehicle owner’s manual or manufacturer regarding location of airbag or

other sensors near the mounting location.

3. Fit the additional headlamp with washer, spring washer, and nut.

WIRING HARNESS INSTALLATION

The wiring harness is pre-assembled and fully insulated and sleeved.

1. Lay out wiring so that all connections (battery, relay, switch, & lights) will have more than

sufficient length.

Larson Electronics LLC WWW.MAGNALIGHT.COM

9419 E US HWY 75, Kemp, TX 75143 - P: 903-498-3363 F: 903-498-3364 E: sales@magnalight.com

2. Find a suitable location to mount the relay on the battery side of the engine compartment.

Make sure the mounting location is not exposed to water spray, excessive heat, or moving parts.

3. Attach both power supply wires (red) to the positive (+) battery terminal.

4. Connect the ground wire (black) to the vehicle chassis or the negative (-) battery terminal,

connect the wiring to switch.

5. Locate an unused grommet on the firewall. If one cannot be found, drill a ½” hole with no

obstructions on either side and away from moving parts and other wiring.

6. Feed the switch connector through the firewall and into the vehicle interior to the switch

mounting location.

7. Select a suitable mounting location for the switch such as the dashboard or center console.

8. Clean and dry both the mounting surface and the back of the switch and use double sided

adhesive pad to secure.

9. Plug the switch connector into the wiring harness and secure all loose wiring to ensure safe

vehicle operation.

10. Feed the auxiliary light wiring to each light with the shorter length going to the light on the

battery side.

11. Plug the power supply socket to each light and attach the ground wire (black) to the vehicle

chassis.

OPTIONAL LOW/HIGHT BEAM CONNECTION

Some states require auxiliary lighting to be connected to low/high beam wiring so that they may only be

used when your headlights are on. An additional benefit is to prevent battery draining in case the

headlights are accidentally left on. If you choose not to do this you may connect directly to the positive

terminal and your auxiliary lights will operate at any time using the switch.

Feed the single (red) wire to the positive (+) low or high beam wire and attach using the blue

wiretap connector.

TURNING ON AND TESTING OPERATION

1. Remove electrical tape from the negative (-) terminal and re-connect onto the battery.

2. Turn on ignition switch and activate the auxiliary light switch.

NOTE: If you attached the optional connector to the low or high beam you will need to turn on your

headlamps to that position before the auxiliary lamps will light.

If lamps do not light, check fuse(s) and all wiring connections.

Use wire ties to secure all loose wiring in the engine compartment, making sure all wiring is away from

moving parts and excessive heat.

CAUTION: IT IS STRONGLY RECOMMENDED THAT ANTI-SEIZE BE USED ON ALL MOUNTING

HARDWARE.

Inhaltsverzeichnis

Andere Larson Electronics Scheinwerfer Handbücher

Larson Electronics

Larson Electronics GL-2110-F Handbuch

Larson Electronics

Larson Electronics HUL-18-TRP Bedienungsanleitung

Larson Electronics

Larson Electronics LED10W-1SCB Bedienungsanleitung

Larson Electronics

Larson Electronics LE-217 Bedienungsanleitung

Larson Electronics

Larson Electronics HL-85-HID-CPR Bedienungsanleitung

Larson Electronics

Larson Electronics RCL700 Bedienungs- und Wartungshandbuch

Larson Electronics

Larson Electronics GL-8130-M Bedienungsanleitung

Larson Electronics

Larson Electronics GL-9950 Handbuch

Larson Electronics

Larson Electronics RL-85-10W1 Bedienungsanleitung

Larson Electronics

Larson Electronics HUL-LED25WRE-CPR-TRP Bedienungsanleitung

Larson Electronics

Larson Electronics APM-GL20004 Bedienungsanleitung

Larson Electronics

Larson Electronics HUL-LED25WRE-CPR Bedienungsanleitung

Larson Electronics

Larson Electronics HUL-18 Bedienungsanleitung

Larson Electronics

Larson Electronics PML-90LED-DP-120 Bedienungsanleitung

Larson Electronics

Larson Electronics RL-85-3W1 Bedienungsanleitung

Larson Electronics

Larson Electronics GL-4600-XD Handbuch

Larson Electronics

Larson Electronics MUL-30-LED Bedienungsanleitung

Larson Electronics

Larson Electronics Golight RadioRay GL-7 GT Series Bedienungsanleitung

Larson Electronics

Larson Electronics GL-9100H-S Handbuch

Larson Electronics

Larson Electronics GL-9901 Handbuch

Larson Electronics

Larson Electronics GL-30675-F Bedienungsanleitung

Larson Electronics

Larson Electronics RL-14 Bedienungsanleitung

Larson Electronics

Larson Electronics GL5150-12IR Handbuch

Larson Electronics

Larson Electronics Golight Stryker GL-30064ST Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

Guangzhou Yinhe Lighting&Sound Equipment Factory

Guangzhou Yinhe Lighting&Sound Equipment Factory NE-204 Bedienungsanleitung

LIVARNO home

LIVARNO home 375304 2101 Originalbetriebsanleitung

Cameo

Cameo CLQS40WW Bedienungsanleitung

Leviton

Leviton Ellipsoid 5/50 Bedienungsanleitung

Monacor

Monacor img Stage Line PARL-56PDX/CR Bedienungsanleitung

Vector

Vector SL3AKV Bedienungsanleitung

Quantum

Quantum Q262 Betriebshandbuch

Philips

Philips Vari-lite VL3015LT Bedienungsanleitung

EUROSPOT

EUROSPOT C51 Bedienungsanleitung

DTS

DTS MINI BRICK ARC Bedienungsanleitung

Federal Signal Corporation

Federal Signal Corporation VISIBEAM II Handbuch

ACME

ACME LED-MS350B Bedienungsanleitung

EuroLite

EuroLite Akku flat light 1 Bedienungsanleitung

Commercial Electric

Commercial Electric SPTM-1401 Bedienungsanleitung

Vision & Control

Vision & Control SLB-500-W5K7-P-SL Bedienungsanleitung

Teknik

Teknik FLEXI Bedienungsanleitung

Craftsman

Craftsman CMXLSB10 Bedienungsanleitung

EuroLite

EuroLite LED SLS-144 UV Floor Spot Bedienungsanleitung