Larson Electronics MPD-DS-WM-FDS Series Bedienungsanleitung

MPD-DS-WM-FDS Series

Fused Disconnect Switch

Wall Mount - NEMA 3R

Instruction Manual

Thank you for your purchase of the Larson Electronics MPD-DS-WM-FDS Series fused disconnect switch.

WARNING:

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

CRITICAL SAFETY INSTRUCTIONS:

•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY

RELEVANT LOCAL BUILDING CODES.

•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL

SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.

•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.

•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.

•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP

OBJECTS. SUITABLE FOR DAMP LOCATIONS.

The Larson Electronics MPD-DS-WM-FDS Series Power Distribution Disconnect Switch is designed for reliable, safe and

convenient power distribution at industrial work sites. Designed for wall mounting installations, the disconnect switch is

protected by a NEMA 3R rated, steel enclosure with a ventilated design.

Mounting Holes

MOUNTING

The Larson Electronics MPD-DS-WM-FDS Series Power Distribution Non Fused Disconnect

Switch is designed for wall mounting applications. There are flanges at top and bottom on the

back of the enclosure, allowing the switch to be mounted to any flat surface that is capable of

supporting the load. Choose a sturdy location, and secure the unit to the wall/surface using

appropriately sized hardware for the pre-drilled mounting holes on the flanges of the enclosure.

Always follow all applicable local and national electrical and building codes when

installing this unit.

Note: Consider your plans for bringing in supply power

and running secondary power when mounting, and be

sure to leave clearance for all necessary wiring and

operations, as well as for opening the door.

Wiring

Only a licensed electrician should install this product, in all locations, especially in outdoor areas where

weatherproofing may be required.

Note: Always check product nameplate or labeling for voltage ratings! Follow all applicable local and National

Electrical and building code when installing.

There are two types of installation methods: Conduit installation or cable installation. If the enclosure is complete with

factory installed entry hardware, run all your wiring through entry hardware and refer to the wiring diagram included with

your unit for completing wiring connections.

If the enclosure does not include entry hardware, select the appropriate hubs or cable connectors and install them per the

IOM included with the hardware.

Installation of approved conduit hubs or cable connectors

CAUTION: FIELD INSTALLED OPENINGS:

For field-installed openings, use a hole saw, metal drill bit, or pneumatic type punch to create an appropriately sized hole

for mounting your selected hardware. Always wear safety glasses and protective clothing when working.

Larson Electronics, LLC Phone: (877) 348-9680 Fax: (903) 498-3364 www.larsonelectronics.com 1of 2

MPD-DS-WM-FDS Series

Conduit/Cable Installation

In situations where the metal cable connector and conduit hubs must be bonded to the ground system, this can be

accomplished by installing them either by method 1 or method 2 as shown.

Method 1: Enclosures with flange plates using threaded

openings through the flange plate and standard

locknuts. Flange Plate must be connected to the

internal grounding system using jumper wires.

Method 2: Enclosures without flange plates using a hole

“through the enclosure” with grounding

locknut.

These locknuts must be bonded between each other and to the

grounding system using jumper wires. After the entry hardware is

installed, connect the appropriate conduit or cable.

Note: All unused enclosure openings must be closed using

approved close-up plugs with standard locknuts.

Refer to IOM sheet of cable connector for proper installation

IMPORTANT: When connecting conductors:

•Strip the wire so that the insulation covers the wire up to the

terminal.

•Make sure all wires are connected to the correct terminals,

per the wiring diagram.

•Tighten all terminal blocks/screws.

OPERATION

MPD-DS-WML-NFDS Series switches operate with an exterior switch, allowing the unit to be cycled off and on without

the need to open it. Two-position OFF-ON and three-position ON-OFF-ON are the most common setups, and switches

are typically labeled to show the current position.

REPLACING FUSES

Always turn off supply power before opening unit or performing any maintenance! All maintenance should be

performed only by a licensed electrician with knowledge of these types of electrical systems.

In the event you need to replace fuses, disconnect power to unit and open the door of the enclosure. Remove the

faulty fuse(s) and replace with like parts of the same type and ratings. Close unit door once fuses are in place and unit

is ready for testing. Ensure the load on the switch is not exceeding the capacity and ratings for the disconnect switch

and fuses, then restore supply power. Refer to the wiring diagram that was included with your disconnect switch if

needed.

REPLACEMENT PARTS

The MPD-DS-WM-FDS is designed to provide years of reliable performance. Should the need for replacement parts

arise, please contact Larson Electronics.

Larson Electronics, LLC Phone: (877) 348-9680 Fax: (903) 498-3364 www.larsonelectronics.com 2of 2

THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION REQUIREMENTS.

SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON ELECTRONICS BY EMAIL AT

SAL[email protected] OR BY PHONE AT 1-877-348-9680 FOR FURTHER ASSISTANCE.

PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.

Inhaltsverzeichnis

Andere Larson Electronics Schalten Handbücher

Larson Electronics

Larson Electronics GAU-SW-4P-WW-24V Bedienungsanleitung

Larson Electronics

Larson Electronics PDU-ATS-100A-208Y.120-3PH Bedienungsanleitung

Larson Electronics

Larson Electronics EPS-PB10-MS-SPDT Bedienungsanleitung

Larson Electronics

Larson Electronics EPS-PB10 Bedienungsanleitung

Larson Electronics

Larson Electronics EPS-25A-3W Bedienungsanleitung

Larson Electronics

Larson Electronics EPSW-3PH-20 Bedienungsanleitung

Larson Electronics

Larson Electronics EPCS-PL-2X-RG Bedienungsanleitung

Larson Electronics

Larson Electronics EPS-DCSW-50A-600V Bedienungsanleitung

Larson Electronics

Larson Electronics EPS-2XPB-SG-600V-LKC Bedienungsanleitung

Larson Electronics

Larson Electronics VPLHL-7WLED-50-NP Bedienungsanleitung

Larson Electronics

Larson Electronics EPS-10HP-3PST Bedienungsanleitung

Larson Electronics

Larson Electronics EPNFDS-MTS-200A-3P Bedienungsanleitung

Larson Electronics

Larson Electronics EPCS-PB10-2XMPB-2PS-N4X-M1 Bedienungsanleitung

Larson Electronics

Larson Electronics LM HZ-EW-SP1097-HV Series Bedienungsanleitung

Larson Electronics

Larson Electronics LED-ILS Bedienungsanleitung

Larson Electronics

Larson Electronics EPS-FS-B-2PSW Bedienungsanleitung

Larson Electronics

Larson Electronics EPSW-1PH-20 Bedienungsanleitung

Larson Electronics

Larson Electronics EXHL-TRN-LE1 Series Bedienungsanleitung

Larson Electronics

Larson Electronics EPS-SW1-ESTP Bedienungsanleitung

Larson Electronics

Larson Electronics EXP-RT-3PH-MIN.5-208V Bedienungsanleitung

Larson Electronics

Larson Electronics EPS-PB10-GRN-2XC Bedienungsanleitung

Larson Electronics

Larson Electronics EPS-1XPB-1XPL-M1-24V Bedienungsanleitung

Larson Electronics

Larson Electronics EXP-EL-CSS-250A-R1-NO Bedienungsanleitung

Larson Electronics

Larson Electronics EPSW-30A-WP Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung