Larson Electronics EXP-EL-CSS-250A-R1-NO Bedienungsanleitung

EXP-EL-CSS-250A-R1-NO

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

1of 3

Explosion Proof AC Current Sensing Switch

240V AC/DC Output - 0-250A Sensing Range - NO Contacts

Instruction Manual

Thank you for your purchase of the Larson Electronics EXP-EL-CSS-250A-R1-NO.

WARNING:

READ CAREFULLY BEFORE INSTALLING FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE.

CRITICAL SAFETY INSTRUCTIONS:

•INSTALLATION SHOULD ONLY BECONDUCTED BY A QUALIFIED ELECTRICIAN IN ACCORDANCE WITH NEC AND ANY

RELEVANT LOCAL BUILDING CODES.

•RISK OFFIRE OR ELECTRIC SHOCK. FIXTURE INSTALLATION REQUIRES KNOWLEDGE OF FIXTURE'S ELECTRICAL

SYSTEMS. IFNOTQUALIFIED, CONTACT A QUALIFIED ELECTRICIAN.

•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.

•MAKE SURE THE SUPPLY VOLTAGE IS THE SAME AS THE FIXTURE'S RATED VOLTAGE.

•TO PREVENT WIRING DAMAGE OR ABRASION, DO NOT EXPOSE WIRING TO EDGES OF SHEET METAL OR SHARP

OBJECTS. SUITABLE FOR DAMP LOCATIONS.

IMPORTANT

READ CAREFULLY BEFORE INSTALLING THIS FIXTURE. SAVE THESE INSTRUCTIONS FOR FUTURE

REFERENCE. THE EXP-EL-CSS-250A-R1-NO MUST BE WIRED IN ACCORDANCE WITH NATIONAL

ELECTRICAL CODE AND ALL APPLICABLE LOCAL CODES. PROPER GROUNDING IS REQUIRED FOR SAFETY.

WE STRONGLY ENCOURAGE ONLY ALICENSED ELECTRICIAN INSTALL, OPERATE AND MAINTAIN THIS

PRODUCT. IF YOU ARE NOT QUALIFIED OR UNFAMILIAR WITH ANY ASPECT OF THIS INSTRUCTION SHEET,

CONSULT AN ELECTRICIAN. THERE ARE NO SERVICEABLE PARTS INSIDE.

WARNING: MAKE SURE POWER IS TURNED OFF BEFORE STARTING THE

INSTALLATION OR PERFORMING ANY MAINTENANCE.

RISK OF FIRE/ELECTRIC SHOCK –DISCONNECT POWER AT BREAKER BEFORE INSTALLING OR SERVICING.

RISK OF PERSONAL INJURY –FIXTURE MAY BECOME UNSTABLE OR DAMAGED IF NOTINSTALLED PROPERLY.

RISK OF BURN –ALLOW FIXTURE TO COOL BEFORE SERVICING.

WARNING

TO AVOIDTHE RISKOF FIRE,EXPLOSION OR ELECTRIC SHOCK, THIS PRODUCT SHOULD BE INSTALLED,

INSPECTEDAND MAINTAINEDBY A QUALIFIED ELECTRICIANONLY, IN ACCORDANCEWITHALL

APPLICABLEELECTRICAL CODES.

TO AVOIDELECTRIC SHOCK:

•BE CERTAIN ELECTRICAL POWER IS OFF BEFORE AND DURING INSTALLATION AND MAINTENANCE.

•PRODUCT MUST BE CONNECTED TO A WIRING SYSTEM WITH AN EQUIPMENT-GROUNDING

CONDUCTOR.

TO AVOID EXPLOSION:

•MAKE SURE THE SUPPLY VOLTAGE IS WITHIN THE VOLTAGE RATING.

•ENSURE THE MARKED T RATING IS LESS THAN THE IGNITION TEMPERATURE OF THE HAZARDOUS

ATMOSPHERE.

•DO NOT OPERATE IN AMBIENT TEMPERATURES ABOVE THOSE INDICATED ON THE PRODUCT

NAMEPLATE.

•DO NOT OPERATE IF THE LENS, CORD, SEALS, HOUSING, RECEPTACLES, ETC. IS CRACKED OR

DAMAGED. IF SO, DISCONTINUE USE AND CONTACT MANUFACTURER FOR REPLACEMENT PARTS.

•ALL FASTENERS SHOULD BE PROPERLY SEATED.

The EXP-EL-CSS-250A-R1-NO from Larson Electronics is an Explosion Proof AC Current Switch designed for power

monitoring and circuit control in Class I, II and III rated facilities. The solid-state switch is equipped with a fixed core, non-

adjustable trip point and normally open contacts. This explosion proof device offers a current sensing range of 0-250A.

EXP-EL-CSS-250A-R1-NO

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

2of 3

WIRING

We strongly encourage a licensed electrician install this product,in all locations especially in outdoor areas

where weatherproofing may be required. Universal voltage driver permits operation at 240V AC/DC.

Warning: Check product label for correct input voltage!

INSTALLATION

1. Run the wire to be monitored through aperture.

2. Mount the sensor.

3. Connect output wiring.

a. Use 22AWG (0.33mm²) up to 14AWG (2.5mm²) copper wires, 75/90°C insulation.

b. Ensure load matches the output shown on the sensor label.

For All Versions

Run wire to be monitored through the aperture (opening) in the sensor.

The AC Current Switch can be located in the same environment as motors,

contactors, heaters, pull-boxes, and other electrical enclosures. Mounting can be

done in any position or hung directly on wires with a wire tie. Ensure at least one

inch clearance exists between sensor and other magnetic devices.

Split-Core Versions (-S Suffix)

Press the tab in the direction as shown to open the sensor. After placing wire in

aperture, press the hinged portion firmly downward until a click is heard and the tab

pops out fully.

Important!

Keep Contact

Area CLEAN!

To Open

Press Tab

Toward Hinge.

KEEP SPLIT-CORE SENSORS CLEAN.

Silicone grease is factory applied on the mating surfaces to prevent rust and improve performance. Be careful not to allow grit or dirt

onto the grease in the contact area. Operation can be impaired if the mating surfaces do not have good contact. Check visually

before closing.

Output Wiring

Connect control or monitoring wires to the sensor. Use 22AWG (0.33mm²) up to

14AWG (2.5mm²) copper wire and tighten terminals to 5 in lbs (0.6 Nm) torque. Be

sure the output load does not exceed the switch rating.

CAUTION: INCANDESCENT LAMPS CAN HAVE “COLD

FILAMENT INRUSH” CURRENT OF UP TO 10 TIMES THEIR

RATED AMPERAGE. USE CAUTION WHEN

SWITCHING LAMPS ON AND OFF.

The output connection is simple, and is not polarity sensitive. Bring the control

circuit voltage to one terminal, and connect the controlled load to the other. When

closed, the contact will pass the control circuit voltage from the source to the load.

AC Current Switch

Setpoint Adjustment

The AC Current Switch setpoint is fixed and non-adjustable:

1. Output contacts are solid-state. Check output status by applying voltage to the contacts and reading the voltage drop across the contacts.

An ohmmeter set on “Continuity” will give misleading results.

Monitored Amps Output

Fixed Split N.O.

Below 0.75 A 1.25 A OPEN

Above 0.75 A 1.25 A CLOSED

EXP-EL-CSS-250A-R1-NO

Larson Electronics, LLC Phone: (800) 369-6671 Fax: (903) 498-3364 www.larsonelectronics.com

3of 3

USE AND CARE

Unauthorized modification may impair the function and/or safety of this device and could affect the life of the equipment.

Always check for damaged or worn out parts before using the device. Store it in a secure place out of the reach of

children when not in use. Inspect for good working condition prior to storage and before re-use.

REPLACEMENT PARTS

The EXP-EL-CSS-250A-R1-NO is designed to provide years of reliable performance. Should the need for replacement

parts arise, please contact Larson Electronics.

THESE INSTRUCTIONS MAY NOT COVER ALL DETAILS OR VARIATIONS OF THIS PRODUCT FOR YOUR EQUIPMENT OR INSTALLATION

REQUIREMENTS. SHOULD FURTHER INFORMATION NOT COVERED BY THESE INSTRUCTIONS BE REQUIRED, PLEASE CONTACT LARSON

ELECTRONICS BY EMAIL AT SA[email protected] OR BY PHONE AT 1-800-369-6671 FOR FURTHER ASSISTANCE.

PLEASE VISIT LARSONELECTRONICS.COM FOR WARRANTY AND RETURN INFORMATION.

TROUBLESHOOTING

1. Sensor is always tripped

A. Switch has been overloaded and contacts are burned out.

Check the output load, remembering to include inrush or inductive loads (coils, motors, ballasts).

B. The setpoint may be too low.

Verify monitored circuit amps are less than the fixed setpoint of the AC Current Switch.

2. Sensor will not trip

A. The setpoint may be too high.

Verify monitored circuit amps are greater than the fixed setpoint of the AC Current Switch.

B. Split Core models: The core contact area may be dirty. Open the sensor and clean the contact area.

C. Monitored current is below fixed setpoint.

Loop the monitored wire several times through the aperature until the “sensed” current rises above min-imum. Sensed

Amps = (Actual Amps) x (Number of Loops). Count loops on the Inside of the aperature.

D. Switch has been overloaded and contacts are burned out.

Check the output load, remembering to include inrush on inductive loads (coils, motors, ballasts).

MAINTENANCE

There are no serviceable parts inside the fixture. However, it is good practice to routinely clean and check the

fixture for proper function.

Inhaltsverzeichnis

Andere Larson Electronics Schalten Handbücher

Larson Electronics

Larson Electronics EPS-PB20 Bedienungsanleitung

Larson Electronics

Larson Electronics LM HZ-EW-SP1097-HV Series Bedienungsanleitung

Larson Electronics

Larson Electronics VPLHL-7WLED-50-NP Bedienungsanleitung

Larson Electronics

Larson Electronics EPS-10HP-3PST Bedienungsanleitung

Larson Electronics

Larson Electronics EPS-PB10-2XC-M2-YR Bedienungsanleitung

Larson Electronics

Larson Electronics EPSW-1PH-20 Bedienungsanleitung

Larson Electronics

Larson Electronics LED-ILS Bedienungsanleitung

Larson Electronics

Larson Electronics EPS-DCSW-50A-600V Bedienungsanleitung

Larson Electronics

Larson Electronics EPS-PB10-MS-AT-N4X-V3 Bedienungsanleitung

Larson Electronics

Larson Electronics MPD-DS-WML-NFDS Series Bedienungsanleitung

Larson Electronics

Larson Electronics EPS-SW1-ESTP Bedienungsanleitung

Larson Electronics

Larson Electronics GAU-SW-4P-WW-24V Bedienungsanleitung

Larson Electronics

Larson Electronics C1D2 Bedienungsanleitung

Larson Electronics

Larson Electronics EPO-20A Bedienungsanleitung

Larson Electronics

Larson Electronics EPS-3PSW-MMS Bedienungsanleitung

Larson Electronics

Larson Electronics EPS-PB10-MS-AT-V4 Bedienungsanleitung

Larson Electronics

Larson Electronics EPS-25A Bedienungsanleitung

Larson Electronics

Larson Electronics EPSW-3PH-20 Bedienungsanleitung

Larson Electronics

Larson Electronics EPS-2XPB-SG-600V-LKC Bedienungsanleitung

Larson Electronics

Larson Electronics MPD-DS-WM-FDS Series Bedienungsanleitung

Larson Electronics

Larson Electronics EPL-SW Series Bedienungsanleitung

Larson Electronics

Larson Electronics EPSW-30A-WP Bedienungsanleitung

Larson Electronics

Larson Electronics EPS-25A-3W Bedienungsanleitung

Larson Electronics

Larson Electronics PDU-ATS-100A-208Y.120-3PH Bedienungsanleitung

Beliebte Schalten Handbücher anderer Marken

URC

URC Total Control MFS-8 Bedienungsanleitung

Azbil

Azbil HPQ-D11 Bedienungsanleitung

Sony

Sony DFS-900M Bedienungsanleitung

SICK

SICK i17S Bedienungsanleitung

F&F

F&F SZR-277 Bedienungsanleitung

Shure

Shure UAMS/BK Bedienungsanleitung

Dräger

Dräger X-zone Switch Off Bedienungsanleitung

Asco

Asco Joucomatic 349 Series Bedienungsanleitung

BT Mini Hub Bedienungsanleitung

D-Link

D-Link DES-1226G Bedienungsanleitung

Johnson Controls

Johnson Controls FS80-C Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 7450 ESS-12 Bedienungsanleitung

MicroNet

MicroNet SP1200A Bedienungsanleitung

Ruijie

Ruijie RG-PF2920 Series Installations- und Betriebsanleitung

Altinex

Altinex DA1914SX Bedienungsanleitung

MiLAN

MiLAN MIL-SM2401M Bedienungsanleitung

RJM

RJM MASTERMIND PBC/6X Bedienungsanleitung

Atlas

Atlas MMK-KVM8 Bedienungsanleitung