Lava Aire Fantom Bedienungsanleitung

Introduction:

This ultrasonic mist fan is an attractive and easy to use product with a luxurious finish. It functions as an industrial fan

and an ultrasonic mist machine to make the environment cooler. Please take note that the functions may be used

separately. You will definitely feel the cool wind during hot summer days. This product is suitable for your home, office,

commercial or industrial establishment.

Working Principle:

The Ultrasonic mist fan uses supersonic concussive elements that atomize water down to 1-5 micron (ultra particles),

and through the industrial fan, it spreads the ultrasonic mist into the air and thus cooling down the room temperature.

1. Front grille guard ornament

2. Front guard

3. Blade cap

4. Blade

5. Guard mounting nut

6. Rear guard

7. Motor

8. Iron tube (upper)

9. Iron tube connector

10. Iron tube (lower)

11. Decorative cover

12. Wiring cover

13. Flume

14. Wheel

15. Plastic mist tube

Manufacturedfor: www.LavaHeat.com

Model Name:

JR ZIONI DESIGNER

LAVA AIRE

I T A LIA

Less energy consumption

90%

Technical Specifications

> Rated Voltage : 120V~

> Rated Frequency : 60Hz

Assembly of fan body

1. Install power cord terminal from iron tube (upper) into the iron tube connector, and then insert iron tube (upper) into the

iron tube connector and fasten them by 2 screws.

2. Insert decorative cover and wiring coverinto iron tube (lower).

3. Let power cord terminal from iron tube connector into iron tube (lower), and then fasten iron tube (lower) and connector

by 2 screws.

Assembly of fan body to base

1. Match and fix 6 wheels into their holes of base and press themfirmly.

2. Match and fix two terminals from power cord and flume, and then place iron tube (lower) on the flume and fasten by 4

screws.

3. Lift the decorative cover and then fix wiring cover by 3 screws.

Assembly of rear guard

1. Take out the rear guard mounting nut in a counter-clockwise motion.

2. Insert the rear guard into the motor matching 3 rods on the front side of the motor(the handle must be positioned on the

top)to 3 holes of the rear guard.

3. Fasten the rear guard tightly by turning the guard mounting nut clockwise.

Assembly of fan blade

1. Insert the blade tothe motor shaft and ensure the pin enters the blade slot.

2. Tighten the blade using the blade cap turning it counter-clockwise in the direction with a “TIGHT” arrow indicated on it.

Note: Proper assembly of the blade is of great importance. Otherwise, the blade spins out of direction and can cause

damage tothe appliance.

Assembly of front guard

1. Fix the front guard withthe logo inthe upright position on the rear guard, and then fasten both guards together by clips.

2. Tighten the screw on the guard by screwdriver.

Note: Do not operate the fan without assembling the guards properly and tightly.

Place the fan on the ground in a level position and add water inside the water tank according tothe steps below:

Note: Unplug the unit from the mains before adding or removing water from the tank. Do not add hot water (40 and

above)in the water tank.

Adding water manually

1. Open the water tank cover.

2. Add water inthe flume, take note of the water level.

3. Close the water tank cover.

Note: Please ensure that water level will not be over the allowable limit to avoid spilling water on the floor. See

picture below.

2. Continuous water supply

1. Take out rubber coverfrom the water inlet.

2. Connect one end of water pipe tothe base. (Internal diameter of pipe is 15mm)

3. Connect another end of water pipe tothe tap, and then open the tap.

Note: Do not add dirty water or any additives (such as perfume, essential oil and mosquito repel, etc.), instead add

clean drinking water or purified water to ensure longerlife of the humidifier.

Operating the Fan

Insert plug tothe electrical outlet, and then turn on each switch to operate above functions.

1. Turn on speed switch, to choose the wind speed - Low, Med, High.

2. Pull down oscillation switch, to change the wind direction. Pull up this button again to stop oscillation.

3. Turn on mist switch, the mist will spread out from the mist spray hole, “MIST” function can be used together with or

independently of the fan. If the mist function is used separately, it can increase humidity level in the air.

Safety Precaution

1. Make sure this appliance and the power cord is not damaged before operating. In case of damage, please send the unit

to the authorized technical service center.

2. Do not unplug the unit from the electrical outlet with wet hands.

3. Do not touch the electrical wirings and water inthe tankif the unit isturned on.

4. Do not insert any object into guard and mist spray hole to avoid destroying the unit.

5. Unplug the unit from the electrical outlet when not operating and before moving, installing, uninstalling and cleaning the

unit.

6. Do not pull the plug while the power is on. Always ensure that the plug is fully inserted into the electrical outlet before

operating.

7. Do not add any chemical, metal ingredient into the water tank or flume, as these materials are dangerous and may

cause problems.

8. Automatic switch shall be cut off when water in the tank is not enough. This is to protect the ultrasonic transducer. Add

more water to allow continuous use.

9. This appliance must be used underthe rated voltage and frequency as indicated in rating label.

10. Do not disassemble, repair or modify this appliance on your own or send the unit for repair to an unauthorized person

as warranty will be void.

11. If the power cord is damaged, it must be replaced immediately by the service center to avoid electrical hazard.

12. This appliance is not intended for use by persons (including children) with reduce physical, sensory or mental

capabilities, or lack of experience and knowledge. With proper supervision or instruction concerning use of the appliance

by a person responsible for their safety, they may operate it otherwise.

13. Children should be supervised to ensure that they do not play withthe appliance.

Cleaning and Maintenance

1. Please unplug the unit before cleaning it.

2. Please clean the water tank every two or three weeks, and clean the flume every week.

3. Please take out the water tank when cleaning it and pull the plastic tube out of the atomizing cup properly, then

take out the atomizing cup and clean them.

4. Use a dry cloth to absorb water remaining when cleaning the atomizing cup and dry it using a piece of soft cloth.

Or use mild detergent to clean the atomizing cup if it is dirty.

5. Please add a few drops of lubricant to the motor shaft after cleaning to extend motor life every year.

6. Pack this appliance properly and store it in a cool dry place if you are not using it for a period of time.

Frequently Asked Questions

If your fan is not working properly, please check the followings (1-4 for mist function) before sending to service agent:

Questions

Answers

Solution(s)

1. Why is there no mist and no wind

from fan?

a. Power cord plug is not connected

properly and electric power is off. b.

MIST switch is off.

a. Ensure that the power cord plug is

fully inserted into the electrical outlet

and turn on the electric power. b. Turn

on the MIST switch.

2. The ultrasonic transducer is working

properly but how come there is no mist

spray?

a. Water tank is broken or with crack, so

flume is full of water. b. Fan is not

working.

a. Pour out the water from flume,

change a new water tank. b. Change a

new fan motor.

3. Why is there no mist even though fan

is working?

a. No water or water level is not

enough. b. Bobber doesn’t float in the

water. c. Ultrasonic transducer surface

was filled up. d. Clamp plate of water

level switch is not firmly positioned in

place. e. Ultrasonic transducer is

damaged.

a. Add water. b. Pull out the bobber

and let it float out. c. Clean ultrasonic

transducer with detergent supplied

together with product. d. Reinstall clamp

plate of water level switch. e. Change

the ultrasonic transducer.

4. Why is there a peculiar smell of mist?

a. Peculiar smell of new product will

disappear after a period of using. b.

Dirty water or water storage time is too

long.

a. Take out the tank and open tank

cover, and put it to a ventilated and dry

place. b. Clean water tank and flume

and change the clean water.

5. Why is the fan not operating? a. The plug inserted may be lacking

electricity or fuses may have gone off.

a. Make sure the plug works and check

your fuses.

6.Heavy unit vibration.

a. The rear guard is not installed

tightly. b. The blade cap is loosened. c.

The blade is damaged. d. The blade is

not aligned

a. Install the rear guard tightly. b.

Tighten the blade cap. c. Change a new

fan blade. d. Turn the fan blade 180°

and then reinstall blade.

7. Other unusual problem.

a. Motor appeared smoke or a smell of

burnt. b. Exposed metal parts with

electric or the fan insulation is

damaged. c. The rear cover of motor is

damaged.

a.b.c. Stop using and send to service

agent for repair.

LAVA AIRE

I T A LIA

Manufactured for: www.LavaHeat.com

JR ZIONI DESIGNER

Inhaltsverzeichnis

Andere Lava Aire Lüfter Handbücher

Lava Aire

Lava Aire Amiti CM-126P Bedienungsanleitung

Beliebte Lüfter Handbücher anderer Marken

ELTA FANS

ELTA FANS H03VV-F Bedienungsanleitung

Hunter

Hunter 20714 Gebrauchsanweisung

Emerson

Emerson CARRERA VERANDA CF542ORB00 Bedienungsanleitung

Hunter

Hunter Caraway Gebrauchsanweisung

Panasonic

Panasonic FV-15NLFS1 Bedienungsanleitung

Kompernass

Kompernass KH 1150 Bedienungsanleitung

VES

VES FALA100/12V/TR Bedienungsanleitung

Vertiv

Vertiv Liebert DCD Bedienungsanleitung

Westinghouse

Westinghouse GFP Series Bedienungsanleitung

Venmar

Venmar KUBIX HRV PLUS Series Bedienungsanleitung

Maico

Maico ECR 31 Bedienungsanleitung

Sonnenkonig

Sonnenkonig Dinky Bedienungsanleitung

S&P

S&P ECOWATT HXBR Bedienungsanleitung

Wider

Wider IMP03369BH Bedienungsanleitung

Panasonic

Panasonic F-60DHN Bedienungsanleitung

Hinkley

Hinkley HIGHLAND Bedienungsanleitung

Broan

Broan 766BN Bedienungsanleitung

Premium

Premium PFS16022 Montageanleitung