Lava PayLink-IP/Dial Bedienungsanleitung

Rev. B00

™

LAVA PayLink-IP/Dial

Quick Installation Guide

Congratulations on your purchase of a LAVA PayLink-IP/Dial.

PayLink-IP devices securely connect payment terminals to payment

processors over an Ethernet/TCP/IP connection. Any payment

terminal that can transmit transaction information over a POTS port

can send its information to the The

establishes an SSL-secured connection to the

payment processor, places the serial data in a TCP/IP wrapper and

sends it out its Ethernet port. Data moving the other direction, from

the Ethernet side of the to the payment

terminal, undergoes the same process in reverse.

• Securely network payment terminals

• Stop using dial-up modems

• Eliminate long-distance phone-modem charges

LAVA PayLink-IP/Dial. LAVA

PayLink-IP/DIal

LAVA PayLink-IP/DIal

LAVA PayLink-IP/Dial

With a , you can:

Included with your package, you should have the following:

•

• Power supply

• Quick Installation Guide

Getting Started

Before Proceeding:The PayLink-IP is factory preset with an

IP address of 192.168.0.35. If this IP address conflicts with a

device already installed on the network, follow the

procedure described in the "Configuring network settings"

section of this manual to set the IP address to a usable

address.

Hardware Setup

1. Connect the power supply to the and to

AC power.The power (red) LED will light to indicate that the

unit is receiving power.

2. Connect to the Ethernet RJ-45 jack

of the . Attach the other end of the

crossover network cable to a host PC directly.

Network status is indicated by two LEDs on the RJ-45 connector.

The left (yellow) LED indicates network activity. It is on by default,

turning off when network activity occurs at the PayLink-IP.The right

(green) LED indicates a network link. It is off by default, but lights

when a network link exists.

LAVA PayLink-IP/Dial

an Ethernet cross-over cable

LAVA PayLink-IP/Dial

Power

connector

Power

indicator

Network

connector (RJ-45)

Network

Activity and Link

indicators

3. Open a web browser to the IP address of the PayLink-IP and

configure the device as described in the "Configuration"

section of this manual.

4. After configuring the LAVA PayLink-IPDial, attach it to your

network and connect a payment terminal to its serial port.

Serial port activity is indicated by two status LEDs per port.The

yellow LED lights when the serial port is transmitting data.The

green LED lights when the serial port is receiving data.

Single Port PayLink-IP/Dial

RJ-11 POTS

connector

POTS Tx

indicator

POTS Rx

indicator

Configuration consists of the following:

B. Host configuration

C. Protocol configuration

D. Password selection

E. Upgrading software

A. Configuring network settings

Configuration

A. Configuring network settings

PayLink-IP devices installed on your network will need unique IP

addresses.These are set by using a web browser.

The factory default network settings for the PayLink-IP are:

IP address: 192.168.0.35

Subnet mask: 255.255.255.0

Gateway address: 0.0.0.0

Name: [empty]

Workgroup: [empty]

DHCP detection: disabled

To set a PayLink-IP's network settings, open a web browser and

enter the IP address of the PayLink-IP into the browser's location

bar.The embedded web server running on the PayLink-IP will

display the opening screen of the PayLink-IP.

Configuring PayLink-IP network settings

Click "Configure" if no password has been set, or enter the

password for the PayLink you are configuring, and then click

"Configure." The Configuration menu will open.

Opening screen

Configuration Menu

Choose the "Configure the LAVA PayLink-IP on my network" link. In

the configuration screen that appears, enter the network settings

you wish for that PayLink-IP. Once the new values are entered and

accepted, the PayLink-IP will reboot to implement the new network

settings.

Changing the network settings of a PayLink-IP device that is

installed on a network may make that device unavailable to other

stations that have activated a connection to that device using older

network settings.

NOTE:

The following network parameters can be configured for the LAVA

PayLink-IP/Dial:

Network Settings

Device name

IP address

Subnet mask

Default gateway

HTTP port

DHCP enabled

Use this field to supply a“friendly”name for the

device being configured.The friendly name is optional, and

can be chosen to provide a conveniently-remembered name for

the unit.

The IP address for the will identify the device

on the LAN on which it is located. Any conventional IP address can

be used.The ships with its default IP address

as 192.168.0.35; ensure that this IP address is available on the LAN

onto which the is being installed.

A subnet mask can be configured for the in

this dialog box; by default the has a subnet

mask of 255.255.255.0.

Configure the IP address of the default gateway that the

will use when communicating with devices outside

its network segment.The default gateway is configurable as a 12

digit numeric address.

By default, the communicates on port number

80. A measure of increased security may be obtained by changing

this port number to a non-standard TCP port for HTTP

communications.

When installing the onto a network where IP

addresses are assigned by DHCP servers, please ensure that the

LAVA PayLink-

IP/Dial

LAVA PayLink-IP/Dial

LAVA

PayLink-IP/Dial

LAVA PayLink-IP/Dial

“DHCP enabled” checkbox has been set.The

will then act as a DHCP client and obtain its IP address from the

DHCP server on its LAN that first leases an IP address to the

Use this dialog box to change the TCP port number assigned to the

serial port of the . By default the

assigns TCP port 2300 to its serial port; if another device on

the network is already using this TCP port number, reassign the

serial port to another TCP address.

After making changes to the network settings, four options exist:

This option will register the changes you have entered into the

dialog box and reboot the , implementing the

changes on reboot.

This option will restore factory defaults and reboot the

, implementing the changes on reboot.

This option will discard changes entered into the dialog box and

return you to the “Administrator Menu”screen.

This option will reboot the device with the settings currently

implemented, and discard changes entered into the dialog box and

not submitted.

Assigned local TCP port

Submit changes and reboot device

Restore factory defaults and reboot device

Exit without changes

Reboot device

LAVA PayLink-IP/Dial

LAVA

PayLink-IP/Dial

LAVA PayLink-IP/Dial LAVA PayLink-

IP/Dial

LAVA PayLink-IP/Dial

LAVA

PayLink-IP/Dial

B. Host configuration

The PayLink-IP/Dial POTS port can be configured through a web

browser.The settings for the LAVA PayLink-IP/Dial's host connection

should match the requirements of the hosting server used by the

payment terminal.

Host Configuration

The Host Side configuration dialog provides settings for a Primary

Host, a Secondary host, and two additional user-defined hosts. Each

host can be configured or SDLC or asynchronous communications.

Inhaltsverzeichnis

Andere Lava Netzwerk-Hardware Handbücher

Lava

Lava HQ-ST Link Benutzerhandbuch

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Lanner

Lanner NCA-1525 Bedienungsanleitung