Ledj LEDJ01 Bedienungsanleitung

www.prolight.co.uk

COLOR BURST SOUND ACTIVE

(order code: LEDJ01)

USER MANUAL

LEDJ COLOR BURST SAFETY

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE YOUR INITIAL START-UP!

CAUTION!

Keep this equipment away from rain,

moisture and liquids.

SAFETY INSTRUCTIONS

Every person involved with the installation, operation & maintenance of this

equipment should:

- Be competent

- Follow the instructions of this manual

CAUTION! TAKE CARE USING THIS EQUIPMENT!

HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!

Before your initial start-up, please make sure that there is no damage caused during

transportation. Should there be any, consult your dealer and do not use the equipment.

To maintain the equipment in good working condition and to ensure safe operation, it is

necessary for the user to follow the safety instructions and warning notes written in this

manual.

Please note that damages caused by user modifications to this equipment are not

subject to warranty.

LEDJ COLOR BURST SAFETY

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused

by the non-observance of this manual or any unauthorised modification to the

equipment.

•Never let the power-cable come into contact with other cables. Handle the

power-cable and all mains voltage connections with particular caution!

•Never remove warning or informative labels from the equipment.

•Do not open the equipment and do not modify the equipment.

•Do not connect this equipment to a dimmer-pack.

•Do not switch the equipment on and off in short intervals, as this will

reduce the system’s life.

•Only use the equipment indoors.

•Do not expose to flammable sources, liquids or gases.

•Always disconnect the power from the mains when equipment is not in

use or before cleaning! Only handle the power-cable by the plug. Never

pull out the plug by pulling the power-cable.

•Make sure that the available voltage is between 220v/240v.

•Make sure that the power-cable is never crimped or damaged. Check the

equipment and the power-cable periodically.

•If the equipment is dropped or damaged, disconnect the mains power supply

immediately. Have a qualified engineer inspect the equipment before

operating again.

•If the equipment has been exposed to drastic temperature fluctuation (e.g.

after transportation), do not switch it on immediately. The arising

condensation might damage the equipment. Leave the equipment switched

off until it has reached room temperature.

•If your product fails to function correctly, discontinue use immediately. Pack

the unit securely (preferably in the original packing material), and return it to

your Prolight dealer for service.

•Only use fuses of same type and rating.

•Repairs, servicing and power connection must only be carried out by a

qualified technician. THIS UNIT CONTAINS NO USER SERVICEABLE

PARTS.

•WARRANTY; One year from date of purchase.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual, the

product may suffer damage and the warranty becomes void.

Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,

lamp failure etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and property!

LEDJ COLOR BURST INTRODUCTION

Introduction

Features

CONTROL FEATURES

• 4-channel DMX-512 LED Par Can

• Blackout/Dimmer/Strobe

• Sound Active

• Individual control of Red, Green and Blue LED’s

Features

• 86 LED’s :- Red (44), Green (21), and Blue (21)

• Ultra bright LED’s

• RGB colour mixing

• Built-in colour change programs

• Power consumption: 10W

• Up to 100,000-hour LED life span

• Master/Slave mode

• Programmable: Any universal DMX-512 controller

DMX Channel Summary

CHANNEL

FUNCTION

BLACKOUT/STROBE/DIMMER

RED

GREEN

BLUE

LEDJ COLOR BURST OVERVIEW

Product Overview

Operating Instructions

The Colour Burst is a DMX-512 controllable, full RGB colour mixing Par Can made up of high

efficiency and super bright LED’s. There are three colour groups (red, blue and green) whose

intensity can be controlled individually allowing the creation of an unlimited range of colours.

The Colour Burst can operate in stand-alone, Master/Slave, Sound Active and via DMX-512

control utilizing 4 channels.

LEDJ COLOR BURST OPERATING INSTRUCTIONS

Master/Slave

The Master/Slave mode will allow you to link up as many units as you want in a daisy chain

fashion. In this mode, the first unit in the daisy chain will automatically command the slave units:

1) Connect all units in a daisy chain fashion as described in the section following

2) Master Unit: Set dipswitch No: 9 to on and No: 10 to off.

3) Slaves: Set dipswitch No: 10 to the on position and all others to the off position

Stand-Alone Mode

You can run the fixtures in an automatic stand-alone mode by simply setting all fixtures

to run as master units without daisy chaining.

Sound Activation

The LED Par Can has a built-in microphone which enables it to operate in Sound to Light mode.

Set the sensitivity control to the desired level, and the Color Burst will change colour to the beat

of the music. Set dip switch 8+9 to ON to activate Sound Mode.

Daisy Chain Connection

1) Connect the (male) 3 pin connector side of the DMX cable to the output (female) 3 pin

connector of the first fixture

2) Connect the end of the cable coming from the first fixture which will have a (female) 3 pin

connector to the input connector of the next fixture consisting of a (male) 3 pin connector.

Proceed to connect from the output as stated above to the input of the following fixture

and so on.

LEDJ COLOR BURST BUILT-IN OPTIONS

Built-in Program Options

In this mode it is possible to access various in-built programs & control the speed of them.

Firstly set the dip switch #9 to ON position & #10 to OFF

Dip switches #1 – 3 adjust the program selection. By selecting a combination of ON or OFF

different patterns will be produced.

Dip switches #4 – 8 controls the speed of these patterns.

#4 ON = Very Fast

#5 ON = Fast

#6 ON = Medium

#7 ON = Slow

#8 ON = Very Slow.

Manual Control Options

With all the dipswitches set to the off position, the dipswitches 1 – 8 will control 3 levels of

intensity for red and green LED’s and 2 levels of intensity for blue LED’s.

This allows you to statically set a colour of preference without the use of a controller. By setting

different intensities for all 3 LED colours you can compose a colour of your choice.

Manual Intensity Control RGB Mix

DMX Control Mode

Operating in a DMX control mode environment gives the user the greatest flexibility when it

comes to customising or creating a show. In this mode you will be able to control each individual

trait of the fixture and each fixture independently. The Colour Burst uses 4 channels of control.

Enable the DMX control by setting dipswitch No: 10 to the ON position. Use dipswitches 1 – 9 to

address each fixture accordingly.

LEDJ COLOR BURST OPERATING INSTRUCTIONS

Setting the DMX address

The DMX mode enables the use of a universal DMX controller. Each fixture requires a “start

address” from 1- 511. A fixture requiring one or more channels for control begins to read the

data on the channel indicated by the start address. For example, a fixture that occupies or uses

7 channels of DMX and was addressed to start on DMX channel 100, would read data from

channels: 100,101,102,103,104,105 and 106. Choose a start address so that the channels used

do not overlap. E.g. the next unit in the chain starts at 107.

Set the start address using the group of dipswitches located usually on the bottom of the fixture.

Each dipswitch has an associated value. Adding the value of each switch in the ON position will

provide the start address. Determining which switches to toggle ON given a specific start

address can be accomplished in the following manner. By subtracting the largest switch value

possible from the selected start address until zero is achieved.

LEDJ COLOR BURST DMX SET UP

DMX-512:

• DMX (Digital Multiplex) is a universal protocol used as a form of communication

between intelligent fixtures and controllers. A DMX controller sends DMX data

instructions from the controller to the fixture. DMX data is sent as serial data that

travels from fixture to fixture via the DATA “IN” and DATA “OUT” XLR terminals

located on all DMX fixtures (most controllers only have a data “out” terminal).

DMX Linking:

• DMX is a language allowing all makes and models of different manufactures to

be linked together and operate from a single controller, as long as all fixtures and

the controller are DMX compliant. To ensure proper DMX data transmission,

when using several DMX fixtures try to use the shortest cable path possible. The

order in which fixtures are connected in a DMX line does not influence the DMX

addressing. For example; a fixture assigned to a DMX address of 1 may be

placed anywhere in a DMX line, at the beginning, at the end, or anywhere in the

middle. When a fixture is assigned a DMX address of 1, the DMX controller

knows to send DATA assigned to address 1 to that unit, no matter where it is

located in the DMX chain.

DATA Cable (DMX cable) requirements (for DMX operation):

• The LEDJ Color Burst can be controlled via DMX-512 protocol. The DMX

address is set on the back of the unit. Your unit and your DMX controller require

a standard 3-pin XLR connector for data input/output (figure 1).

Figure 1

Also remember that DMX cable must be daisy chained and

cannot be split.

Further DMX cables can be

purchased from all good sound and

lighting suppliers or Prolight dealers.

Please quote:

CABL10 – 2M

CABL11 – 5M

CABL12 – 10M

LEDJ COLOR BURST DMX SET UP

Notice:

• Be sure to follow figures 2 & 3 when making your own cables. Do not connect

the cable’s shield conductor to the ground lug or allow the shield conductor to

come in contact with the XLR’s outer casing. Grounding the shield could cause a

short circuit and erratic behaviour.

Special Note: Line termination:

• When longer runs of cable are used, you may need to use a terminator on the

last unit to avoid erratic behaviour.

Figure 4

Using a cable terminator (part number CABL90) will decrease the

possibilities of erratic behaviour.

5-Pin XLR DMX Connectors:

• Some manufactures use 5-pin XLR connectors for data transmission in place of

3-pin. 5-Pin XLR fixtures may be implemented in a 3-pin XLR DMX line. When

inserting standard 5-pin XLR connectors in to a 3-pin line a cable adaptor must

be used. The Chart below details the correct cable conversion.

3- Pin XLR to 5-PIN XLR Conversion

Conductor 3-Pin XLR out 5-Pin XLR in

Ground shield Pin 1 Pin 1

Negative (-) Pin 2 Pin 2

Positive (+) Pin 3 Pin 3

Termination reduces signal transmission

problems and interference. It is always advisable

to connect a DMX terminal, (resistance 120

Ohm 1/4W) between Pin 2 (DMX-) and Pin 3

(DMX+) of the last fixture

Andere Handbücher für LEDJ01

Inhaltsverzeichnis

Andere Ledj Scheinwerfer Handbücher

Ledj

Ledj PERFORMER 54 RGBW Bedienungsanleitung

Ledj

Ledj LEDJ01 Bedienungsanleitung

Ledj

Ledj STAGE COLOUR 24 TRI Bedienungsanleitung

Ledj

Ledj STAR18 Bedienungsanleitung

Ledj

Ledj Q Colour Bedienungsanleitung

Ledj

Ledj Performer 18 Quad Zoom Bedienungsanleitung

Ledj

Ledj Eco LED 64 Bedienungsanleitung

Ledj

Ledj Quad illuminator Bedienungsanleitung

Ledj

Ledj Stage Par Quad MKII Bedienungsanleitung

Ledj

Ledj LEDJ98 Bedienungsanleitung

Ledj

Ledj Stage Wash 36 Bedienungsanleitung

Ledj

Ledj LEDJ286 Bedienungsanleitung

Ledj

Ledj ALU ZOOM PAR 64 Bedienungsanleitung

Ledj

Ledj INTENSE 12D4 CW Bedienungsanleitung

Ledj

Ledj ALU ZOOM PAR 64 Bedienungsanleitung

Ledj

Ledj HEX Par 7 Bedienungsanleitung

Ledj

Ledj Xterior Wash 131 Bedienungsanleitung

Ledj

Ledj Q Pix Batten LEDJ97 Bedienungsanleitung

Ledj

Ledj Omni WA-36 Bedienungsanleitung

Ledj

Ledj STAGE WASH U.V. 36 LEDJ106 Bedienungsanleitung

Ledj

Ledj LEDJ280 Bedienungsanleitung

Ledj

Ledj PERFORMER 36 RGB Bedienungsanleitung

Ledj

Ledj Slimline 36 RGBW Bedienungsanleitung

Ledj

Ledj Q Batten LEDJ300 Bedienungsanleitung

Beliebte Scheinwerfer Handbücher anderer Marken

VIZULO

VIZULO Micro Martin Benutzerhandbuch

EuroLite

EuroLite LED IP FL-100 SMD Bedienungsanleitung

Cooper Wheelock

Cooper Wheelock XB12 Bedienungsanleitung

Allen + Roth

Allen + Roth 17624-000 Bedienungsanleitung

ADJ

ADJ 4 STAGE PAK Bedienungsanleitung

Cooper Lighting

Cooper Lighting EGL91SW233 Bedienungsanleitung

Max

Max 37496 Bedienungsanleitung

BEGA

BEGA 85 143 Bedienungsanleitung

Beamz

Beamz 151.226 Bedienungsanleitung

EuroLite

EuroLite LED IP FL-8 Bedienungsanleitung

Perel

Perel ELS3 Bedienungsanleitung

Perel

Perel ELS3WD Bedienungsanleitung

LumX

LumX LM 36130 Bedienungsanleitung

Xtricity

Xtricity 4-80053 Bedienungsanleitung

Stahl

Stahl 6521/4 Series Bedienungsanleitung

Ecosense

Ecosense EcoSpec Bedienungsanleitung

Ayrton

Ayrton minipanel FX Bedienungsanleitung

Commercial Electric

Commercial Electric TPAR2-PC-4K-BZ Bedienungsanleitung