Ledj HBR 1D Bedienungsanleitung
www.prolight.co.uk
(Order code: LEDJ123)
IMPORTANT:
The manufacturer will not accept liability for any resulting damages caused
by the non-observance of this manual or any unauthorised modication to the
equipment.
• Never let the power-cable come into contact with other cables. Handle the
power-cable and all mains voltage connections with particular caution!
• Never remove warning or informative labels from the equipment.
• Do not open the equipment and do not modify the equipment.
• Do not switch the equipment on and off in short intervals, as this will reduce the
system’s life.
• Only use the equipment indoors.
•Donotexposetoammablesources,liquidsorgases.
• Always disconnect the power from the mains when equipment is not in use or before
cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling
the power-cable.
• Make sure that the available voltage is between 220v/240v.
• Make sure that the power-cable is never crimped or damaged. Check the equipment
and the power-cable periodically.
• If the equipment is dropped or damaged, disconnect the mains power
supply immediately.
Haveaqualiedengineerinspecttheequipmentbeforeoperatingagain.
•Iftheequipmenthasbeenexposedtodrastictemperatureuctuation(e.g.after
transportation), do not switch it on immediately. The arising condensation might
damage the equipment. Leave the equipment switched off until it has reached room
temperature.
• If your product fails to function correctly, discontinue use immediately. Pack the unit
securely(preferablyintheoriginalpackingmaterial),andreturnittoyourProlight
dealer for service.
• Only use fuses of same type and rating.
•Repairs,servicingandpowerconnectionmustonlybecarriedoutbyaqualied
technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.
• WARRANTY; One year from date of purchase.
OPERATING DETERMINATIONS
If this equipment is operated in any other way, than those described in this manual,
the product may suffer damage and the warranty becomes void.
Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,
lamp failure etc.
Do not endanger your own safety and the safety of others!
Incorrect installation or use can cause serious damage to people and property.
Over view:
Front:
Rear:
Features:
7 Preset colour buttons for instant colour selection.
6 Buttons for dimmer, sound, mood, meteor, fade and change.
9 Flow buttons for instant light shows.
Sound active function with adjustable sensitivity.
Blackout,ood&strobefunctions.
1, Blackout mode:
When you power up your HBR-1D controller, the LED above the “BLACKOUT” button will
illuminate, indicating that the unit is set to blackout mode. To exit the blackout mode simply press
any one of the function buttons.
2, Preset colour mode
In this mode you can select one of the seven preset colours by pressing one of the designated
colourbuttons.Onceyouhaveselectedyourcolouryoucannowsetthedesiredashspeedfrom
slow - fast by using the “FLASH SPEED”slider.(0=slow,255=fast)
3, Dimmer mode
Toactivatethismoderstpressthe‘DIMMER” button and make sure that the “SPEED/DIMMER”
sliderissetto255.Nowyoucanuseanyofthe“RED, GREEN and BLUE” colour sliders to set
thedesiredoutputbrightnessandcolour.Tosettheashspeedusethe “FLASH SPEED” slider
tosetthedesiredspeed(0=slow,255=fast).
4, Sound Active mode
To activate this mode, press the “SOUND” button. You will need to adjust the “SPEED/DIMMER”
slidertosetthemusicinputsensitivitylevel.(0=low,255=high)Youcanthenusethe“FLASH
SPEED”slidertosetthedesiredstrobespeed.(0=slow,255=fast)
5, Colour Mood mode
To activate this mode, press the “MOOD” button, then adjust the speed to the desired level using
the “SPEED/DIMMER” slider(0=slow,255=fast).Youcannowusethe“FLASH SPEED” slider
tosetthedesiredstrobespeed(0=slow,255=fast).Thismodeisidealforwallandup/down
lighting to create different mood effects in bars, restaurants and shops etc.
6, Meteor mode
To activate this mode press the “METEOR” button, then adjust the speed to the desired level by
using the “SPEED/DIMMER” slider(0=slow,255=fast).Theunitwillnowrunfromrighttoleft
through its built-in preset colours. You can now use the “FLASH SPEED” slider to set the desired
strobespeed(0=slow,255=fast).
7, Colour Fade mode
To activate this mode press the “FADE” button, then adjust the speed to the desired level by us-
ing the “SPEED/DIMMER” slider(0=slow,255=fast).Theunitwillnowfadethroughitsbuilt-in
preset colours. You can now use the “FLASH SPEED” slider to set the desired strobe speed
(0=slow,255=fast).
8, Colour change mode
To activate this mode press the “CHANGE” button and adjust the speed to the desired level by
using the “SPEED/DIMMER” slider(0=slow,255=fast).Theunitwillnowchangethroughits
built-in preset colours. You can now use the “FLASH SPEED” slider to set the desired strobe
speed(0=slow,255=fast).
Flow function button:
The Flow buttons 1-9 are equipped with built-in chase patterns. Each “FLOW” chase button is
described below.
Flow 1:
Flows from left to right through its built-in preset colours.
Flow 2:
Flows from left-right, right-left, running through its built-in preset colours.
Flow 3:
Flows from left-right, fading through its built-in preset colours.
Flow 4:
Bounces from left-right, right-left, through its built-in preset colours.
Flow 5 :
Anti-clockwise rotation running through its built-in preset colours.
Flow 6:
Clockwise rotation running through its built-in preset colours.
Flow 7:
Left to right in a worm fashion through its built-in preset colours.
Flow 8:
Jumps from left to right with individual colours or you can mix it yourself with two colours of your
choice. To chose the desired colours use the “RED DIMMER” slider.
Flow 9:
Jumps from left-right, right-left with selected individual colours or you can mix it yourself with two
colours of your choice. To chose the desired colours use the “RED DIMMER” slider.
NOTE: Each of the above ow patterns can be controlled by using the “SPEED/ DIMMER”
slider to select the desired running speed and the “FLASH SPEED” slider
to chose the desired ash level.
Specications
Power supply: DC 9-12V 300mA Min.
Size:294x145x64mm
Weight: 1.1 Kgs
Notes:
Inhaltsverzeichnis
Andere Ledj Beleuchtungsausrüstung Handbücher
Ledj
Ledj LEDJ377 Bedienungsanleitung
Ledj
Ledj FLEX30 Bedienungsanleitung
Ledj
Ledj Aspect Bedienungsanleitung
Ledj
Ledj Mini Pix 9 Panel Bedienungsanleitung
Ledj
Ledj Spectra Par 15Q8 PRO Bedienungsanleitung
Ledj
Ledj Stage Par CZ200 Dual White Bedienungsanleitung
Ledj
Ledj Intense 9P10 RGBWA LED Slim Panel Bedienungsanleitung
Ledj
Ledj STRATOS UV Bedienungsanleitung
Ledj
Ledj Slimline CW Series Bedienungsanleitung
Ledj
Ledj Slimline Q5 Series Bedienungsanleitung
Ledj
Ledj LEDJ352A Bedienungsanleitung
Ledj
Ledj Pixel Storm 6 Tri Batten Bedienungsanleitung
Ledj
Ledj Rapid QB1 RGBW Battery Uplighter Bedienungsanleitung
Ledj
Ledj Colour Storm Quad Bedienungsanleitung
Ledj
Ledj LEDJ162 Bedienungsanleitung
Ledj
Ledj ECO LED Par 56 Bedienungsanleitung
Ledj
Ledj Slimline 12Q5 Series Bedienungsanleitung
Ledj
Ledj LEDJ188 Bedienungsanleitung
Ledj
Ledj STRATOS Bedienungsanleitung
Ledj
Ledj Omni Tri-9 Bedienungsanleitung
Beliebte Beleuchtungsausrüstung Handbücher anderer Marken
Qazqa
Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung
Commercial Electric
Commercial Electric 54568141 Bedienungsanleitung
CREE LIGHTING
CREE LIGHTING 304 Series Bedienungsanleitung
Goobay
Goobay 49867 Bedienungsanleitung
ECOMAN ITALIA
ECOMAN ITALIA LED T8 Bedienungsanleitung
Alkalite
Alkalite Krypton KT-81 Bedienungsanleitung
