Ledj BlockBuster 6 Bedienungsanleitung

www.prolight.co.uk

BlockBuster 6

(Order code: LEDJ73)

LEDJ BlockBuster 6 Safety

WARNING

FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL CAREFULLY

BEFORE YOUR INITIAL START-UP!

CAUTION!

Keep this equipment away from rain,

moisture and liquids.

SAFETY INSTRUCTIONS

Every person involved with the installation, operation & maintenance of this

equipment should:

- Be competent

- Follow the instructions of this manual

CAUTION! TAKE CARE USING THIS EQUIPMENT!

HIGH VOLTAGE-RISK OF ELECTRIC SHOCK!!

Before your initial start-up, please make sure that there is no damage caused during

transportation. Should there be any, consult your dealer and do not use the

equipment.

To maintain the equipment in good working condition and to ensure safe operation, it is necessary

for the user to follow the safety instructions and warning notes written in this manual.

Please note that damages caused by user modications to this equipment are not

subject to warranty.

LEDJ BlockBuster 6 Safety

IMPORTANT:

The manufacturer will not accept liability for any resulting damages caused

by the non-observance of this manual or any unauthorised modication to the

equipment.

• Never let the power-cable come into contact with other cables. Handle the power-cable

and all mains voltage connections with particular caution!

• Never remove warning or informative labels from the equipment.

• Do not open the equipment and do not modify the equipment.

• Do not connect this equipment to a dimmer-pack.

• Do not switch the equipment on and off in short intervals, as this will reduce the

system’s life.

• Only use the equipment indoors.

• Do not expose to ammable sources, liquids or gases.

• Always disconnect the power from the mains when equipment is not in use or before

cleaning! Only handle the power-cable by the plug. Never pull out the plug by pulling the

power-cable.

• Make sure that the available voltage is between 220v/240v.

• Make sure that the power-cable is never crimped or damaged. Check the equipment and

the power-cable periodically.

• If the equipment is dropped or damaged, disconnect the mains power supply immediately.

Have a qualied engineer inspect the equipment before operating again.

• If the equipment has been exposed to drastic temperature uctuation (e.g. after

transportation), do not switch it on immediately. The arising condensation might damage

the equipment. Leave the equipment switched off until it has reached room temperature.

• If your product fails to function correctly, discontinue use immediately. Pack the unit

securely (preferably in the original packing material), and return it to your Prolight dealer

for service.

• Only use fuses of same type and rating.

• Repairs, servicing and power connection must only be carried out by a qualied

technician. THIS UNIT CONTAINS NO USER SERVICEABLE PARTS.

• WARRANTY; One year from date of purchase.

OPERATING DETERMINATIONS

If this equipment is operated in any other way, than those described in this manual,

the product may suffer damage and the warranty becomes void.

Incorrect operation may lead to danger e.g.: short-circuit, burns, electric shocks,

lamp failure etc.

Do not endanger your own safety and the safety of others!

Incorrect installation or use can cause serious damage to people and property.

LEDJ BlockBuster 6 Operations

Operation

When the power is turned on, the LCD display will be as below:

Press the “MODE” button to activate the main menu: Built-in programme, Auto run, DMX mode,

Slave mode and Sound mode.

• Built-in programme: Runs one of the 14 built-in programmes

• Auto run: Runs the built-in programmes one after another in a continuous loop

• DMX mode: Control by external DMX controller

• Slave mode: The unit in this mode can be linked to run with another unit set to Master

mode.

• Sound mode: Programmes are activated to the sound by the built-in microphone

1) A programme is a sequence of different steps, with the BlockBuster 6 you can select up to 14

different programmes. Press the “set up” and the UP/DOWN buttons to select between pro

grammes(00-14) and select the desired programme value (step time and ash).

For example: Press the “set up” button to move the cursor to select 02 and then desired Sp

(step time) or Fs (ash speed).

• SP: Step time value from 001 - 100 • FS: Flash speed from value 00 - 100

2) Auto run

Runs 14 programmes in a continuous loop, the frequency means the speed of the run

times can be set via the UP and DOWN buttons.

3) DMX mode:

You can control the units individually using your DMX controller

a) The control board allows you to assign the DMX address which is dened as the rst channel

from which the BlockBuster 6 will respond from the controller. For address setting, press the

“set up” button until the display shows as follows:

WELCOME

TO USE

FLOOD LED

324 RGB

ONE SECOND

02.SLOW D

S001 F012

AUTO RUN

FQN:00

DMX MODE

ADDR:001

LEDJ BlockBuster 6 Operations

b) DMX-protocol

The control board allows you to set 5, 8, 11 or 20 DMX channels for different applications.

Press the “set up” button until the display is as follows:

Set the desired channels (5, 8, 11 or 20) Via the UP and DOWN buttons

1, Set for 20 Channels:

The dimmer occupies the rst channel when DMX value is smaller than 251, the ash occupies

the second channel, each spot occupies 3 channels, six spots occupy 18 channels and the full

unit occupies 20 channels.

2, Set for 11 channels:

The dimmer occupies the rst channel when the DMX value is smaller than 251, the ash

occupies the second channel, every 2 spots occupy 3 channels, six spots occupy 9 channels

and the full unit occupies 11 channels.

3, Set for 8 channels:

The dimmer occupies the rst channel when the DMX value is smaller than 251, the ash

occupies the second channel, every 3 spots occupy 3 channels, six spots occupy 6 channels

and the full unit occupies 8 channels.

4, Set set 5 channels:

The dimmer occupies the rst channel when the DMX value is smaller than 251, the ash

occupies the second channel, six spots occupy the same 3 channels, and the full unit

occupies 5 channels.

5, During any of the four above DMX modes the rst DMX channel value must be between 251

and 255.

DMX MODE

CH NO:20

LEDJ BlockBuster 6 DMX-Protocol

CH1 CH2 CH3 CH4 CH5

251 - 255

0-10

11-21

22-32

33-43

44-54

55-65

66-76

77-87

88-98

99-109

110-120

121-131

132-142

143-153

154-164

165-175

176-186

187-197

198-208

209-219

220-230

231-255

BLACKOUT

RED

YELLOW

GREEN

CYAN

BLUE

PURPLE

WHITE

SLOW DREAM

FAST DREAM

COLOUR FADE

COLOUR CHANGE

FLOW 1

FLOW 2

FLOW 3

FLOW 4

DOUBLE FLOW 1

DOUBLE FLOW 2

MULTI COLOUR

2 COLOUR FLOW 1

2 COLOUR FLOW 2

SOUND ACTIVE

NOT USED

FLASH

0-225

(0-28HZ)

FLASH

0-225

(0-28HZ)

SPEED

0-255

SPEED

0-255

FLASH

0-225

(0-28HZ)

COLOUR

0-255

SENSITIVITY

0-255

(32 grade)

MODE DMX

VALUE

4, Slave mode:

Press the MODE button repeatedly until the display shows Slave Mode. The unit will now

follow another that is set to Master Mode

5, Sound mode:

Adjust the audio level input by pressing the UP and DOWN buttons. The range is 0-31

SOUND

SENS:31

DMX-Protocol

NOT USED

NOT USEDNOT USED

LEDJ BlockBuster 6 Specications

Specications:

• 324 high intensity LED’s

• Red 108, Green 108, Blue 108 (total 324)

• LED beam angle: 30 degree’s

• Dimensions: 800 x 100 x 75mm

• Weight: 5.5kg

• Power in: 240v ~ 50Hz

• Power consumption: 35 watts

Inhaltsverzeichnis

Andere Ledj Beleuchtungsausrüstung Handbücher

Ledj

Ledj Omni Tri-9 Bedienungsanleitung

Ledj

Ledj HEX Par 9 Bedienungsanleitung

Ledj

Ledj Stage Wash 18 Bedienungsanleitung

Ledj

Ledj minibar TC Bedienungsanleitung

Ledj

Ledj HBR 1D Bedienungsanleitung

Ledj

Ledj Archi BAR 48 Bedienungsanleitung

Ledj

Ledj Stage Par CZ200 Dual White Bedienungsanleitung

Ledj

Ledj Stage Par CZ200 3200K Bedienungsanleitung

Ledj

Ledj LEDJ P85 Bedienungsanleitung

Ledj

Ledj Intense 9P10 RGBWA LED Slim Panel Bedienungsanleitung

Ledj

Ledj SPECTRA PAR 7T3 Bedienungsanleitung

Ledj

Ledj Artisan 1000 Bedienungsanleitung

Ledj

Ledj Spectra Par 15Q8 PRO Bedienungsanleitung

Ledj

Ledj Spectra Q40 MKII Bedienungsanleitung

Ledj

Ledj LEDJ387 Bedienungsanleitung

Ledj

Ledj Spectra QX40 Pixel MKII Exterior Fixture Bedienungsanleitung

Ledj

Ledj LEDJ377 Bedienungsanleitung

Ledj

Ledj STAR18 Bedienungsanleitung

Ledj

Ledj ALU ZOOM PAR 64 Bedienungsanleitung

Ledj

Ledj LEDJ266 Bedienungsanleitung

Ledj

Ledj Pixel Storm 6 Tri Batten Bedienungsanleitung

Ledj

Ledj Slimline 3HEX12 Series Bedienungsanleitung

Ledj

Ledj PERFORMER 54 RGBW LEDJ250 Bedienungsanleitung

Ledj

Ledj LED-56 Bedienungsanleitung

Beliebte Beleuchtungsausrüstung Handbücher anderer Marken

Brizo

Brizo 8SP-MU-4 Bedienungsanleitung

LUCE&LIGHT

LUCE&LIGHT BROM 1.0 Bedienungsanleitung

IKEA

IKEA BJÖRKSPIREA Bedienungsanleitung

Laserworld

Laserworld Evolution Series ES-400RGB Bedienungsanleitung

Alien

Alien RG STAR Bedienungsanleitung

EuroLite

EuroLite LED B-40 Bedienungsanleitung

Qazqa

Qazqa Suplux SL 3 Black 103062 Bedienungsanleitung

Commercial Electric

Commercial Electric 54568141 Bedienungsanleitung

CREE LIGHTING

CREE LIGHTING 304 Series Bedienungsanleitung

Goobay

Goobay 49867 Bedienungsanleitung

ECOMAN ITALIA

ECOMAN ITALIA LED T8 Bedienungsanleitung

Alkalite

Alkalite Krypton KT-81 Bedienungsanleitung

Clas Ohlson

Clas Ohlson GU10 Bedienungsanleitung

DTS

DTS DELTA 10 F Bedienungsanleitung

ring

ring Solar Steplight Bedienungsanleitung

One Stop Gardens

One Stop Gardens 57696 Montageanleitung

Chauvet DJ

Chauvet DJ COREpar UV120 ILS Bedienungsanleitung

SIREM

SIREM Swimeo A2 Bedienungsanleitung