LEGRAND 0 766 22 Bedienungsanleitung

INSTALLATION AND USER GUIDE

SECURE WANDERING

SYSTEM

2 INSTALLATION PRINCIPLE

2 System description

3 DEVICE PRESENTATION AND

INSTALLATION

3 Secure wandering device

6 Secure wandering system - auxiliary elements

7 STANDALONE INSTALLATION

7 Example of installation

9 Wiring - controllers and antennae

10 Operating modes

11 SYSTEM INSTALLATION

11 Example of installation

13 Wiring - controller/antennae and door unit

14 Operating modes

15 COMMISSIONING

15 Factory settings

16 Settings

18 Adjusting the antennae

19 OPERATION

19 Operation in day mode (surveillance)

20 Operation in night mode (intruder)

21 Illuminated and audible signals

22 CHARACTERISTICS

22 Speciﬁcations

23 USAGE CODES

23 Control code

24 CONTROLLER CONFIGURATION

24 Checking the controller parameters

Contents

CONTENTS

Functionality

The secure wandering system is a system which allows

any potential escape attempts by confused patients to

be controlled.

Each exit under surveillance is ﬁtted with a standalone

controller which alerts staff when a person wearing

a special wristband tries to go through it. In the event

that there are no supervisory staff near the exit, this

information can be transmitted to the BUS/SCS nurse

call unit using a door unit Cat. No. 0 766 06 conﬁgured

for this function. This way nurses are immediately

alerted to the escape and which door they have

gonethrough.

The system can operate using two modes:

• Surveillance mode: An alarm is activated when the

wearer of a wristband is close to the exit and this exit is

open.

• Intruder mode: An alarm is activated when an exit

isopened.

Switching from one mode to the other can be done

manually by entering a special code into the controller

keypad or by closing a clock contact.

The staff have a chaperone code which allows a

wristband wearer to be let through an exit under

surveillance without triggering an alarm.

Two control outputs allow:

• The exit to be locked once a wristband is detected

in the vicinity (provide an electromagnetic lock or an

electric door release).

• An audible or illuminated warning signal to be

triggered when an escape alarm is activated.

Safety instructions

This product must be installed in accordance with the

installation instructions, and preferably by a qualiﬁed

electrician. Incorrect installation and use may lead to

the risk of electric shock or ﬁre. Read the manual and

consider exactly where the product is to be ﬁtted before

carrying out installation.

Do not open, remove, alter or modify the device

unless this is speciﬁcally stated in the instructions.

Legrand products must only be opened and repaired

by personnel trained and authorised by Legrand.

Any unauthorised opening or repair voids all liability,

replacement rights and warranties.

Only use Legrand brand accessories.

Operating environment

- This device complies with the directives concerning

exposure to radioelectric frequencies when used

under the normal conditions described in the user

manual. Follow the installation instructions described in

themanual.

- Depending on the conﬁguration, this device regularly

transmits radio waves, the frequency and power of

which comply with ARCEP recommendations.

SYSTEM DESCRIPTION

Installation principle

CONTENTS

Device presentation and installation

SECURE WANDERING DEVICE

Situated close to the exit door, this controller is the

heart of the system.

All auxiliary elements are connected to it.

A 12-button keypad is used to conﬁgure it and

activate special functions (mode changes, alarm

acknowledgement, etc).

Buzzer and LEDs act as a warning if an escape

is detected. The buzzer makes a different sound

depending on the type of alarm (chaperone or fault).

The indicators show the system status simultaneously.

It can be suppressed.

The controller has a built-in antenna and can retrieve

information from the antenna Cat. No 0 766 21 and

door contact Cat. No. 0 431 00.

Depending on its usage mode, the controller:

- Buzzes and ﬂashes

- Can lock the door if it has the necessary ﬁtting

(electromagnetic lock, door release)

- Can trigger a nurse call if connected to the door unit

- Can send a message to the DECT

When the door is locked, it can be unlocked using

special codes.

The coded keypad picks up the wristband signal when

a resident passes through a predeﬁned door.

Requires a modular 12 V=power supply

(Cat.No.4131 05).

Indicates that a door has been crossed by a resident ﬁtted with a wristband Cat. No. 0 766 20.

Works with door unit Cat. No. 0 766 06 conﬁgured for secure wandering which allows acknowledgement and

feedback to the Legrand SCS nurse call unit system.

Door controller Cat. No. 0 766 22 Technical characteristics

• IP 20 - IK 04

• Operating temperature:

0°C to +50°C

• Power supply:

- 12 V=

- 150 mA

• Illuminated signals:

- System power on (status LED)

- Intruder mode (detection LED)

- Wristband detection (detection LED)

• Audible signals:

- Alarm

- Alarm suppressed by chaperone code

• Functions which can be accessed via the keypad:

- Reset alarms

- Chaperone

- Changeover between surveillance/intruder modes

- System parameter settings

• Controller inputs:

- Adjustable connection

- Volt-free contacts

- Voltage detection

5-24 V=

50 mA to 24 V=

- Door contact (NO/NC)

- Chaperone contact (NO)

- Alarm acknowledgement (NO/NC)

- Mode selection

- Panic alarm (NO)

• Volt-free contact outputs:

- Lock: 1 A - 24 VA/60 V=max

- Alarm: 1 A – 24 VA/60 V=max

• Internal antenna (15W30 -->)

• Cable type for link with door unit (system solution):

2 x 0.9 mm pairs

1Bracelet activation

magnet

2Detection LED (orange)

3Status LED (green)

4Code keypad

5Enter key

6Cancel key

7Buzzer

CONTENTS

Device presentation and installation (continued)

Used in the case of wide doors, double doors, placed as close to the exit as possible, ideally 50 cm from the

ground, opposite the controller. This antenna picks up the radio signal from a wristband Cat. No. 0 766 20 and

informs the controller Cat. No. 0 766 22.

The detection radius (around 1 to 15 m) can be set easily using a screwdriver.

A green indicator light indicates that the antenna power is on.

A red indicator light ﬂashes when a wristband is in the detection zone (see setting the antenna).

The antenna activity is permanently checked by the controller.

Technical characteristics

• Power supply: via door controller Cat. No. 0 766 22

• Dimensions (H x W x D): 50 x 100 x 40 mm

• Screwed onto the wall

• IP 20 - IK 04

• Operating temperature: +0°C to +50°C

• Cable type (to controllers 0 766 22):

2 x 0.9 mm pairs

Antenna Cat. No. 0 766 21 (additional antenna)

SECURE WANDERING SYSTEM (CONTINUED)

1Status LED (green)

2Detection LED (red)

CONTENTS

Wristband Cat. No. 0 766 20

Worn on the wrist or the ankle, this waterproof wristband is ﬁtted with an eyelet fastening preventing it from being

taken off by the person under surveillance.

These wristbands are made of anti-allergy plastic which can be in continuous contact with the skin.

The battery has an expected lifetime of more than a year (although replacing the batteries annually is recommended).

The IP 67 protection allows residents to take showers.

The wristbands can also be cleaned by placing them in an alcohol bath for 5 minutes.

They must be removed in the following cases:

- If they are faulty or the battery is dead

- When the resident leaves

- When the resident undergoes an MRI (magnetic resonance imaging) scan

Etc

To remove the wristband, cut it with a pair of round-end scissors.

When a wristband is immobile it switches to low-consumption mode. This can increase the standalone capacity of

the battery to a maximum of 4 years when stored.

Once wristband movement is detected, it switches immediately to operational mode.

Technical characteristics

• IP 55 - IK 08

• Anti-allergy

• Frequency: 869.85 MHz

• Tx: 869.85 MHz - Rx: 446.525 MHz

• Radiated power: < 10 mW

Technical characteristics

• Power supply: 1 x CR2450 3 V battery

• Standalone operation: 18 months with normal usage

• Dimensions (mm): 33 x 40 x 17

• Weight: 28 g in working order

Activation or

deactivation

(5sminimum) by

passing a magnet

over the product

(5sminimum).

Should bedone

close to the

magnet of

controller

Cat. No. 0 766 22.

Wristband number:

last 3 characters.

To be entered for the 9010

and 9011 code settings.

9 804 23

CONTENTS

Device presentation and installation (continued)

Door contact Cat. Nos. 0 431 00/01

Power supply Cat. No. 4 131 05

The magnetic opening sensor must be connected to the “DOOR” input of controller 0 766 22.

Surveillance mode: an escape alarm is only generated on the double condition that a wristband and opening of

the door are both detected.

Intruder mode: an escape alarm is only triggered if the door is opened.

SECURE WANDERING SYSTEM - AUXILIARY ELEMENTS

Technical characteristics

• IP 41 - IK 02

• Operating temperature: -10°C to +70°C

• Cable type (to controllers 0 766 22):

1 x 0.9 mm pair

Technical characteristics

• Power: 15 W

• Operating voltage: 12 V

• Current: 1.25 A

• Dimensions: 5 x 17.5 mm modules

• Cable type (to controller 0 766 22):

2 x 1.5 mm2

• Class II

• Double operating terminal

• Protected by PTC against overloads and

short-circuits

Sensor

DOOR

0 766 22

CONTENTS

Standalone installation

EXAMPLE OF INSTALLATION

The diagram below represents a typical installation for a standalone system (i.e. not connected to the door unit

Cat. No. 0 766 06 of the nurse call unit).

The controller with built-in antenna (15W30 -->) Cat. No. 0 766 22 is normally installed in the immediate vicinity of

the exit door, at a height which allows easy access to the keypad (1.20 m). Antenna Cat. No. 0 766 21 is installed

at a height of around 50 cm opposite the controller.

If the exit under surveillance is very wide (between 1 and 15 metres) a maximum of two extra antennae placed

on either side of the passageway can be connected to the same controller. This avoids having to set the antenna

sensitivity too high, which risks wristbands in neighbouring rooms being detected.

As with any radio-controlled system, the antenna position is crucial for wristband detection performance and

careful consideration must be given to where it is installed. Equally, wherever possible wristbands must be placed

in an identical manner on all residents under surveillance (for example, on the right wrist if the antenna is to their

right when they go through the exit).

The maximum wiring distance between antenna and controller is 200 metres.

0 766 22

0 766 20

1 - 15 m

0 766 21

0 431 00

123

456

789

≈ 0.5 m

2 x 1.5 mm2

2 x 0.9 mm2

2 x 2 x 0.9 mm2

≈ 1.20 m

4 131 05

CONTENTS

Standalone installation (continued)

Outdoor installation:

The secure wandering system is not intended for outdoor installation. However, surveillance of this type of exit is

possible where the installation is adapted:

- The controller must always be installed indoors.

- The antenna boxes must be placed in weatherproof enclosures made from non-conductive materials (plastic,

PVC, etc).

- The enclosure must be protected from direct sunlight in order to avoid the risk of excessive temperatures inside

the box.

Selecting a door release or lock:

• Door release: ﬂush-mounted installation

- Cable type (to controller 0 766 22): 2 x 1.5 mm2

- Cat. No. 0 408 95: undervoltage door release 12 V=- 600 mA. For operation at emergency exits

- Cat. No. 0 408 98: shunt trip door release 12 V±/=- 500 mA

• Electromagnetic lock: surface-mounted installation

- Cable type (to controller 0 766 22): 2 x 1.5 mm2

- Cat. No. 0 767 07: 300 kg lock

- Cat. No. 0 767 08: 500 kg lock

EXAMPLE OF INSTALLATION (CONTINUED)

Andere LEGRAND Controller Handbücher

LEGRAND

LEGRAND Mosaic Bedienungsanleitung

LEGRAND

LEGRAND 0 663 37 Bedienungsanleitung

LEGRAND

LEGRAND 0 784 48 Bedienungsanleitung

LEGRAND

LEGRAND 3550 Bedienungsanleitung

LEGRAND

LEGRAND HD4657M3 Bedienungsanleitung

LEGRAND

LEGRAND 0 663 35 Bedienungsanleitung

LEGRAND

LEGRAND Wattstopper DLM LMJA-8 Series Bedienungsanleitung

LEGRAND

LEGRAND HA7000 Bedienungsanleitung

LEGRAND

LEGRAND 0 884 07 Bedienungsanleitung

LEGRAND

LEGRAND Wattstopper LMRC-611MCC-A Bedienungsanleitung

LEGRAND

LEGRAND 0 884 06 Bedienungsanleitung

LEGRAND

LEGRAND Arteor 5 742 74 Bedienungsanleitung

LEGRAND

LEGRAND 488 43 Bedienungsanleitung

LEGRAND

LEGRAND Wattstopper LMRC-111-16M Bedienungsanleitung

LEGRAND

LEGRAND Raritan SRC-0100 Bedienungsanleitung

LEGRAND

LEGRAND Wattstopper DCLV2 Service-Handbuch

LEGRAND

LEGRAND Adorne LC7001 Bedienungsanleitung

LEGRAND

LEGRAND 4 238 40 Bedienungsanleitung

LEGRAND

LEGRAND Wattstopper LMPL-101 Bedienungsanleitung

LEGRAND

LEGRAND Raritan SRC-0100 Bedienungsanleitung

LEGRAND

LEGRAND LE00282AC Bedienungsanleitung

LEGRAND

LEGRAND 0 663 40 Bedienungsanleitung

LEGRAND

LEGRAND Valena Allure Series Bedienungsanleitung

LEGRAND

LEGRAND 0 648 84L Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch