LEGRAND C2G 29977 Bedienungsanleitung

rev.03/20 Manual_29977

Network Controller for HDMI® over IP

(Model: 29977)

Operation Manual

Page 2

No part of this publication may be reproduced, stored in a retrieval system, or transmitted in any

form or by any means, electronic, mechanical, photocopying, recording or otherwise without

prior written permission of the author.

Trademarks:

Legrand and C2G are registered trademarks of Legrand.

Page 3

Table of Contents

1. Overview.....................................................................................................................................4

1.1. Description...............................................................................................................................4

1.2. Features....................................................................................................................................5

2. Technical Specifications ............................................................................................................6

3. Installation and Use ...................................................................................................................7

3.1. Part List....................................................................................................................................7

3.2. Product Overview ....................................................................................................................8

3.3. Installation Procedure ..............................................................................................................9

3.4. Ethernet Web Interface –Device Management .....................................................................19

3.5. Extender Models 29975 and 29976........................................................................................22

4. Troubleshooting .......................................................................................................................49

5. Appendix –IP Command API................................................................................................50

6. Product Warranty Policy...................................................................................................51

Page 4

Overview

1.1.

Description

The C2G Network Controller for HDMI over IP (model: 29977) is a Linux-based PC

that allows users to control hub-installed C2G products.

When installed on a local area network (LAN), the C2G Network Controller can scan

the LAN for C2G products and allows the user to auto-discover, configure and control

these products through an Ethernet Web interface.

Applications include but are not limited to commercial and residential AV systems,

classroom projector systems, digital signage, video wall systems, boardroom systems,

multi-room systems, classroom training, retail systems, collaborative PC systems, and

medical information systems.

Figure 1: System Overview

Page 5

1.2.

Features

(Front View) (Rear View)

Front Panel

•Power LED

•Power button

•Audio in (3.5 mm)

•Three (3) USB 2.0 ports

•SS USB 3.0 port

•RS232 Port

Back Panel

•VGA video out port

•HDMI video out port

•Two (2) LAN ports (RJ-45 jack) –“LAN 1” port for AV over IP subnet

•Audio out (3.5 mm)

•Power connector

Figure 2: C2G Network Controller

Page 6

Technical Specifications

Specifications

CPU

Intel Celeron J1800 Processor, @ 2.41GHz 4 cores

Memory

2GB DDR3

Display

Integrated Intel HD Graphics, 1x HDMI and 1x VGA

Keyboard and Mouse

USB keyboard and mouse (not required and not included)

Peripherals

• USB 2.0 ports (3x)

• SS USB 3.0 port (1x)

• Network gigabit interface (2x)

• VGA Video out port (1x)

• HDMI Video out port (1x)

• Audio in via 3.5mm port (1x)

• Audio out via 3.5mm port (1x)

• RS232 port (1x)

Operating System

Ubuntu 18.04 LTS

Temperature/Humidity

Operating: 0 ºC to 50 ºC, Storage: -20 ºC to 80 ºC

Humidity: 10% to 90% (non-condensing)

Dimensions

5.24 x 5.00 x 1.38 inch (133 x 127 x 35 mm)

Weight

1.5lbs (0.7kg)

Accessories Included

External 12VDC @ 2A Power Adaptor

Regulatory

FCC, CE, RoHS, WEEE

Order Information

29977 Network Controller for HDMI over IP

Table 1: Technical Specifications

Page 7

Installation and Use

3.1.

Part List

The C2G Network Controller comes with the following parts:

• Base unit (1x)

• External Power Adapter (1x)

Please verify that both parts are present before proceeding.

Figure 3: Base Unit

Page 8

3.2.

Product Overview

The external connections and connection indicators of the C2Gl Network Controller

are detailed in Figure 4 and Figure 5. Please familiarize yourself with them before

installing the unit.

A1= DC Power

A2= HDMI video out

A3= VGA video out

A4= RJ45 Ethernet LAN 1

A5= RJ45 Ethernet LAN 2

A6= Audio out

A1= Audio In

A2= SS USB

A3= 2.0 USB Ports

A4= RS232

A5= Power LED

A6= Power Button

Figure 4: Rear Panel

Figure 5: Front Panel

Page 9

3.3.

Installation Procedure

Note that the examples below assume that the Ethernet Switch used does not support

WiFi, and a Router with WiFi capability is required in order to communicate with

smartphones and tablets for control purposes.

Setting the Ethernet Switch & Router to the same Subnet as C2G Devices:

The C2G Network Controller comes with two Ethernet ports. LAN 1 is configured

with a static IP address which is 192.168.168.50. LAN 1 port should be connected in

to the same network switch where all the C2G equipment is connected. Note that

LAN 2 port is configured as a DHCP client, and can be utilized for control purpose.

The C2G AV over IP Encoders (TX) and Decoders (RX) are set to support DHCP by

default. When no DHCP server is available the AV over IP Encoders and Decoders

fallback to a static IP address of:

•192.168.168.62 (for the 29975 Encoders)

•192.168.168.63 (for the 29976 Decoders)

These C2G products (Network Controller and the AV over IP Encoders & Decoders)

work in conjunction with a PoE (PSE) Ethernet Switch (supporting IGMP and Jumbo

Frames) and a Router of your choice with WiFi capability to be able to communicate

with a smartphone or tablet. Also, in the case where one Ethernet Switch does not

have sufficient ports for the number of AV over IP Encoders and Decoders to be

connected, then it is recommended that the Ethernet Switch be a stackable Ethernet

Switch. The use of a smartphone or tablet to manage the C2G devices with the C2G

AVoIP Control App (model: 29986) is the preferred method of control, however C2G

devices may also be managed via the Network Controller web interface.

In order for the DHCP server within the Ethernet Switch to support the C2G device

subnet, set the static IP of the Ethernet Switch to 192.168.168.1 (recommended

setting). Refer to the Ethernet Switch manual for instructions on how to accomplish

this. The Router with WiFi capability, must also be placed on the same subnet as the

C2G devices and it should be set with a Static IP address, we recommend using a

Static IP address of 192.168.168.2. Refer to your Router documentation on how to

accomplish this.

Setting C2G Devices, Ethernet Switch and Router to an Existing Subnet:

If the C2G AV over IP devices are being installed in an existing environment that has

a working subnet already configured that cannot be easily changed, then the subnet of

the C2G devices, the Ethernet Switch (if a new Ethernet Switch is required), and the

Router with Wifi (if a new Router is required) must be changed in order to match the

existing subnet. For this case we will use 192.168.2.x as an example subnet already in

place and which must be supported. Note that this is only an example and may not

necessarily reflect your actual subnet address.

Page 10

If the Ethernet Switch does not already reside in the example subnet of 192.168.2.x,

then set the static IP of the Ethernet Switch to a free static IP address (for the sake of

this example we will use an IP address of 192.168.2.1). Refer to the Ethernet Switch

manual for instructions on how to accomplish this. C2G also has example guides

specific to the Cisco SG350 Series, Luxul AMS-1208P Series, and NetGear S3300

Series, which may be found on the C2G website.

If the Router with WiFi does not already reside in the example subnet of 192.168.2.x,

then set the static IP of the Router to a free static IP address (for the sake of this

example we will use an IP address of 192.168.2.2). Refer to your Router

documentation on how to accomplish this.

The C2G AV over IP Encoders and Decoders are set by default to support DHCP and

will automatically be set to the subnet specified by the DHCP Server. These units need

only be physically connected into the network as described in their respective

Installation Guides and by using the 29977 Network Controller for HDMI over IP to

discover them. But before the Network Controller can be used, the new Network

Controller subnet must also be set.

To change the subnet of the Network Controller requires a two-step process:

Process 1: Configuring the IP address of the Network Controller

Process 2: Physically installing the Network Controller in the network

Note:

• An example subnet address of 192.168.2.x of the existing network on which the Network

Controller will be installed is assumed for this example process.

• The Network Controller LAN 1 port comes with a static IP address of 192.168.168.50 and

with DHCP disabled. This process explains how to change it to the example subnet of

192.168.2.x.

Process 1: Configuring the IP address of the Network Controller

Refer to Figure 4 and Figure 5.

1. On the back panel of the Network Controller:

A. Plug the supplied power adaptor into the DC power jack. Ensure that the other

end of the power adaptor is plugged into a power socket.

B. Ensure that the power switch on the front of the unit is ON position (front

button • pressed in).

C. Connect one end of an Ethernet cable to the LAN 1 Ethernet port. Ensure that

the other end of the Ethernet cable is connected to a computer.

Refer to Figure 6.

2. On the computer to which the Network Controller is connected, open up an

Internet browser (Explorer, Chrome, Firefox, etc.) and type the following address

in the address bar near the top of the screen:

Andere Handbücher für C2G 29977

Inhaltsverzeichnis

Andere LEGRAND Controller Handbücher

LEGRAND

LEGRAND F401 Bedienungsanleitung

LEGRAND

LEGRAND 0 884 12 Bedienungsanleitung

LEGRAND

LEGRAND Wattstopper LMRC-611MCC Bedienungsanleitung

LEGRAND

LEGRAND DRD9 Bedienungsanleitung

LEGRAND

LEGRAND 0 663 36 Bedienungsanleitung

LEGRAND

LEGRAND Mosaic 335 25 Bedienungsanleitung

LEGRAND

LEGRAND airQast Bedienungsanleitung

LEGRAND

LEGRAND 0 676 46 Bedienungsanleitung

LEGRAND

LEGRAND DPX3-I 1600 Bedienungsanleitung

LEGRAND

LEGRAND Wattstopper LMPL-611-20M Bedienungsanleitung

LEGRAND

LEGRAND Wattstopper LMRC-611MCC-A Bedienungsanleitung

LEGRAND

LEGRAND 0 766 22 Bedienungsanleitung

LEGRAND

LEGRAND ALPTEC 5.2 Bedienungsanleitung

LEGRAND

LEGRAND 0 488 64 Bedienungsanleitung

LEGRAND

LEGRAND 288 12 Bedienungsanleitung

LEGRAND

LEGRAND 0 698 19L Bedienungsanleitung

LEGRAND

LEGRAND adorne WNACB40 Bedienungsanleitung

LEGRAND

LEGRAND 0 673 69 Bedienungsanleitung

LEGRAND

LEGRAND adorne WZ3ACB40 Bedienungsanleitung

LEGRAND

LEGRAND 784 28 Bedienungsanleitung

LEGRAND

LEGRAND Radiant WNRCB40 Bedienungsanleitung

LEGRAND

LEGRAND Wattstopper DCLV2 Bedienungsanleitung

LEGRAND

LEGRAND 0 677 886L Bedienungsanleitung

LEGRAND

LEGRAND Wattstopper LMJA-8125-SM Bedienungsanleitung

Beliebte Controller Handbücher anderer Marken

Digiplex

Digiplex DGP-848 Betriebsanleitung

YASKAWA

YASKAWA SGM series Bedienungsanleitung

Sinope

Sinope Calypso RM3500ZB Bedienungsanleitung

Isimet

Isimet DLA Series Style 2 Installationshandbuch

LSIS

LSIS sv-ip5a Bedienungsanleitung

Airflow

Airflow Uno hab Bedienungsanleitung

ABB

ABB ACS580-01 drives Bedienungsanleitung

Panasonic

Panasonic GM1 Series Bedienungsanleitung

Emerson

Emerson SW93 Bedienungsanleitung

AutoAqua

AutoAqua Smart ATO micro SATO-120P Bedienungsanleitung

Panasonic

Panasonic FP? Positioning Unit RTEX Bedienungsanleitung

Alpha IP

Alpha IP MIOB 21001 Bedienungsanleitung

Siemens

Siemens OpenAir GMA 1 Series Bedienungsanleitung

Surecom

Surecom SR-629 Bedienungsanleitung

Regulus

Regulus SRS1 T Bedienungsanleitung

3M MicroTouch EX113 Bedienungsanleitung

KUHN

KUHN TKS Bedienungsanleitung

S&C

S&C PMH Bedienungs- und Wartungshandbuch