LEGRAND Pass&Seymour RT1 Bedienungsanleitung

TROUBLESHOOTING

To test the time switch:

The pilot light behind the ON/OFF button and time delay indicator light should

be ON when the switch is OFF. Press the ON/OFF button. The connected light or

fan comes ON. The pilot light behind the ON/OFF button turns OFF.

The connected light or fan should turn OFF in the number of minutes indicated

by the time selection indicator light. You can turn it OFF sooner by pressing the

ON/OFF button again.

Light or fan will not turn ON (pilot light is visible):

Press ON/OFF button. The connected light or fan should turn ON. If not:

• Check the light bulb and/or motor switch on the fan mechanism.

• Turn OFF power to the circuit then check wire connections.

Light or fan will not turn ON (no pilot light or indicator is visible):

• Shade the switch from external light to make sure that none of the indicator

lights on the switch are ON.

• Check the light bulb and/or motor switch on the fan mechanism.

• Make certain that the circuit breaker is ON and functioning.

• Turn OFF power to the circuit then check wire connections.

• Call 1.800.223.4185 for technical support.

Light or fan will not turn OFF:

• Press the ON/OFF button. If connected light or fan does not turn OFF, turn

OFF power to the circuit then check wire connections.

Visit our website at: www.passandseymour.com

340792RevB_Eng:NEW 10/23/08 10:54 AM Page 2

Limited FIVE YEAR Warranty

Pass & Seymour/Legrand will remedy any defect in workmanship or material in Pass & Seymour/Legrand products

which may develop under proper and normal use within five years from the date of purchase by a consumer:

(1) by repair or replacement, or, at Pass & Seymour/Legrand’s option, (2) by return of an amount equal to the

consumer’s purchase price. Such remedy is IN LIEU OF ANY AND ALL EXPRESSED OR IMPLIED WARRANTIES OF

MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. Such remedy by Pass & Seymour/Legrand does not

include or cover cost of labor for removal or reinstallation of the product. ALL OTHER FURTHER ELEMENTS OF

DAMAGE (INCIDENTAL OR CONSEQUENTIAL DAMAGES) FOR BREACH OF ANY AND ALL EXPRESSED OR IMPLIED

WARRANTIES INCLUDING WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ARE

EXCLUDED HEREBY. (Some states do not allow disclaimer or exclusion or limitation of incidental or consequential

damages, so the above disclaimers and limitation or exclusion may not apply to you.) ANY IMPLIED WARRANTIES

INCLUDING WHERE REQUIRED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE

SHALL BE LIMITED TO THE FIVE YEAR PERIOD SET FORTH ABOVE. (Some states do not allow limitation on how long

an implied warranty lasts, so the above limitation may not apply to you.)

To ensure safety, all repairs to Pass & Seymour/Legrand products must be made by Pass & Seymour/Legrand or

under its specific direction. Procedure to obtain performance of any warranty obligation is as follows: (1) Contact

Pass & Seymour/Legrand, P.O. Box 4822, Syracuse, NY 13221 for instructions concerning return or repair; (2) return

the product to Pass & Seymour/Legrand, postage paid, with your name and address and a written description of the

installation or use of the Pass & Seymour/Legrand product, and the observed defects or failure to operate, or other

claimed basis for dissatisfaction.

This warranty gives you specific legal rights and you may also have other rights which vary from state to state.

P.O. Box 4822, Syracuse, NY 13221-4822

Technical Support: 800.223.4185 • www.passandseymour.com

340792 Rev. B 07943

340792RevB_Eng:NEW 10/23/08 10:54 AM Page 3

RT1

Time Switch

7-Button Preset

Installation Instructions

SPECIFICATIONS

Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .120VAC, 60HZ

Load

Single Pole Circuit . . . . . . . . . . . . . . . . . . . . . 0 – 600 Watt

Incandescent or fluorescent lamp or 1/6HP fan motor

Time Delay . . . . . . . . . . . . . . . . . . .1, 5, 10, 20, 30, 60 minutes

Environment

Operating Temperature . . . . . . . .32° to 131°F (0° to 55°C)

Humidity . . . . . . . . . . . . . . . . . . . .95% RH, non-condensing

Tools Needed

Insulated Screwdriver

Wire Strippers

Please read all instructions before installing

6 time selection buttons with

activation indicator lights

ON/OFF button with pilot light

340792RevB_Eng:NEW 10/23/08 10:54 AM Page 4

DESCRIPTION AND OPERATION

The RT1 is a time switch that turns OFF the connected light or fan when the

selected time expires. The pilot light behind the ON/OFF button and the time

delay indicator light illuminates while the switch is OFF. When the switch is ON,

the pilot light behind the ON/OFF button turns OFF.

Manual ON

Turn ON the connected light or fan by pressing the desired time button, or the

ON/OFF button. If you press the ON/OFF button, it activates the time delay that

was last used.

Manual OFF

While the timer is active, you can press the ON/OFF button to turn OFF the

connected light or fan without delay.

Changing the selected time

If you decide that you need more or less time than you originally selected,

restart the time switch by pressing the button that matches the amount of time

you think you’ll need.

Call 800.223.4185 for Technical Support

340792RevB_Eng:NEW 10/23/08 10:54 AM Page 5

INSTALLATION & WIRING

1. Prepare the switch box.

After the power is turned OFF at the circuit

breaker box, remove the existing wall plate and

mounting screws. Pull the old switch out from the

wall box.

2. Identify the type of circuit.

In a Single Pole Circuit (see Fig. 2), two single

wires connect to two screws on the existing

switch. A ground wire may also be present and

connected to a ground terminal on the old switch.

A neutral wire should also be present in the

wall box.

CAUTION

For your safety: Connecting a proper ground to the time switch provides

protection against electrical shock in the event of certain fault conditions.

If a proper ground is not available, consult with a qualified

electrician before continuing installation.

Only connect the RT1 to a Single Pole Circuit. The RT1 is not suitable for

3-way switching. If the existing wiring does not match the description for a

Single Pole Circuit, you should consult with a qualified electrician.

3. Prepare the wires.

Tag the wires currently connected to the existing switch,

so that they can be identified later. Disconnect the wires.

Make sure the insulation is stripped off the wires to

expose their copper cores to the length indicated by the

“Strip Gage” in Fig. 3 (approximately 1/2 inch).

Visit our website at: www.passandseymour.com

Strip Gage

1/2"

12.7mm

Fig 3: Wire Stripping

WARNING

Disconnect power to the wall switch box by turning OFF the circuit

breaker or removing the fuse for the circuit before installing the

RT1, replacing lamps, or doing any electrical work.

Fig 2: Typical Single Pole

Switch Wiring

340792RevB_Eng:NEW 10/23/08 10:54 AM Page 6

4. Wire the time switch.

Twist the existing

wires together with

the wire leads on

the time switch as

indicated in the

drawing. Cap them

securely using the

wire nuts provided.

See Fig 4.

• Connect the green

or non-insulated

(copper) GROUND

wire from the circuit

to the GROUND

terminal on the RT1.

• Connect the power

wire from the circuit

(HOT) to the black

wire on the RT1.

• Connect the power

wire to the lamp or fan

(LOAD) to the red wire

on the RT1.

• Connect the NEUTRAL wires from the circuit to the white wire on the RT1.

5. Put the RT1 in the wall box with the time selection buttons

positioned above the ON/OFF button.

Secure it to the wall box with the screws provided.

6. Attach the new cover plate.

7. Restore power to the circuit.

Turn on the breaker or replace the fuse.

Fig 4: Switch Orientation, Wire Connections and

Wall Box Assembly

340792RevB_Eng:NEW 10/23/08 10:54 AM Page 7

REV.DESCRIPTION INT: REV.DATE APPROVED

1 ECO# C01610 MJS

• Print: 2-sided

• Ink Color: Black

• Paper: White 16lb (60g/m sq)

• Final trim size: 12" (Wide) x 6" (High).

• Three (3) fold.

• Final folded size: 4" (Wide) x 6" (High).

TITLE BOX PAGE ONLY.

DO NOT MAKE FILM • DO NOT PRINT

SYRACUSE, NEW YORK

Title:

RT1 Installation Instructions

IF YOU HAVE ANY QUESTIONS REGARDING SPECIFICATIONS OR REQUIRE

ADDITIONAL FILE FORMATTING, PLEASE CONTACT Joyce Rougeau.

Phone: 315.437.7561

Email: jrougeau@aggraphics.com

Drawing

Orig. Drawing Date:29 Rev. #:

Revision Date:

ROUGEAU

Scale: 1:1

All information in this drawing is the property of P&S/Legrand and cannot be copied or used

without the written approval of P&S/Legrand.

Drawn by

PLM

MarCom

Engineering

340792RevB_Eng:NEW 10/23/08 10:54 AM Page 1

Inhaltsverzeichnis

Andere LEGRAND Timer Handbücher

LEGRAND

LEGRAND LEXIC Rex2000 D21F Bedienungsanleitung

LEGRAND

LEGRAND D817SLIMDP Bedienungsanleitung

LEGRAND

LEGRAND Wattstopper RT-200 Bedienungsanleitung

LEGRAND

LEGRAND 4 127 31 Bedienungsanleitung

LEGRAND

LEGRAND 49730 Bedienungsanleitung

LEGRAND

LEGRAND LEXIC 037 81 Bedienungsanleitung

LEGRAND

LEGRAND LEXIC MicroRex T11 Bedienungsanleitung

LEGRAND

LEGRAND LEXIC 037 64 Bedienungsanleitung

LEGRAND

LEGRAND Wattstopper RT-100-I Bedienungsanleitung

LEGRAND

LEGRAND LEXIC 037 09 Bedienungsanleitung

LEGRAND

LEGRAND D817SLIMDP Bedienungsanleitung

LEGRAND

LEGRAND Wattstopper RT-200-W Bedienungsanleitung

LEGRAND

LEGRAND LEXIC 037 25 Bedienungsanleitung

LEGRAND

LEGRAND Mallia 2810 91 Bedienungsanleitung

LEGRAND

LEGRAND Lexic MicroRex D22 Bedienungsanleitung

LEGRAND

LEGRAND LEXIC RondoRex w21 Series Bedienungsanleitung

LEGRAND

LEGRAND 03740 Bedienungsanleitung

LEGRAND

LEGRAND LEXIC 037 05 Bedienungsanleitung

LEGRAND

LEGRAND MicroRex D11 Basic Bedienungsanleitung

LEGRAND

LEGRAND PRO 21 781 50 Series Bedienungsanleitung

LEGRAND

LEGRAND Wattstopper RT-100 Bedienungsanleitung

LEGRAND

LEGRAND MicroRex D21 Bedienungsanleitung

LEGRAND

LEGRAND Wattstopper RT-20 Bedienungsanleitung

LEGRAND

LEGRAND EconoRex MT 499 83 Bedienungsanleitung

Beliebte Timer Handbücher anderer Marken

Intermatic

Intermatic P1131 Bedienungsanleitung

Learning Resources

Learning Resources Time Tracker mini Bedienungsanleitung

CEBEK

CEBEK I-215 Bedienungsanleitung

Somogyi

Somogyi home TS MD 5 Bedienungsanleitung

Profile

Profile 010200280 Bedienungsanleitung

Gizmo

Gizmo T4 Bedienungsanleitung

Tekmar

Tekmar Timer 031 Bedienungsanleitung

Daikin

Daikin DST301B61 Bedienungsanleitung

sisel

sisel ENDA ETM2432 Bedienungsanleitung

B&Q

B&Q TE103 Bedienungs- und Wartungshandbuch

Hozelock

Hozelock AC Plus 2700 Bedienungsanleitung

GIC

GIC Eliro V7DDSS3Eliro V7DFTS3 Bedienungsanleitung

Tork

Tork TU40 Bedienungsanleitung

Emos

Emos EMT400F Bedienungsanleitung

FarmTek

FarmTek Polaris Bedienungsanleitung

Maximum

Maximum CRONUS Bedienungsanleitung

Uberhaus

Uberhaus TD133B Bedienungsanleitung

Clas Ohlson

Clas Ohlson 31-3766 Bedienungsanleitung