LEGRAND C2G31019 Bedienungsanleitung
--
-
--
-
--
-
............................................
..........................................................
...........................................
............................................
........................................
................................................
..........................................................
...............................
...............................................
.................................................
’ .....................................
.........................................
................................
’ ........................................
.....................................................
..............................
....................
.................................................
...................................
.......................................
...................................
.......................................
.........................................................
................................
⑫
⑬
⑭
②
①
③
④
⑤⑥
⑦
⑧
⑨
⑩
⑪
⑮
⑯
⑰
--
-
Transmier Transmier
10 LINK LED On: HDBT link is normal.
Off/Blinking: No HDBT link or link error.
11 Power LED On: Power is applied to the device.
Off: No power is applied to the device.
12 INPUT Button Short press: Switch input source.
13 DISPLAY Button Short press: Turn display on (CEC).
Long press: 3 seconds to turn off display (CEC).
14 AUDIO IN Pass-through audio input. Connect to an audio source.
15 USB-B Host Port USB-B input. Connect to a USB host device.
REAR PANEL DESCRIPTION
16 HDBT OUT Connect to the receiver via a Cat 5e/6/6a/7 cable.
17 Power Pins 12V and G are used for local DC 12V input.
FRONT PANEL DESCRIPTION
1/2 HDMI 1 / HDMI 2 IN Connect up to two HDMI sources using HDMI cables.
3 USB-C IN Connect to a USB-C source using a USB-C cable.
4 UPDATE
USB Micro-B IN Micro USB port for updating firmware or controlling the
transmitter through API commands.
5 RESET
When the transmitter is powered on, use a pointed stylus to
hold down this button for five or more seconds to reboot and
then release. The transmitter will reboot and restore to its
factory defaults.
6/7 HDMI 1 / HDMI 2 LED One light will be on, indicating which input is selected.
8 USB-C LED
9 HDCP LED On: HDCP protected content is being transmitted.
Blinking: Non-HDCP protected content is being transmitted.
Off: No content is being transmitted.
• Two HDMI inputs, One USB-C input and one HDBT output
• Extend 4Kx2K at 60Hz (4:2:0) up to 130 and 1080p at 60Hz up to 230 with Cat 6a/7 cable.
• Extend 4Kx2K at 60Hz (4:2:0) up to 115 and 1080p at 60Hz up to 200 with Cat 5e/6 cable.
• Supports automac switching
• Addional analog audio input pass-through allows for audio distribuon to the HDBT
receiver side
• High-speed USB 2.0 pass-through over HDBT up to 230
• Supports rmware updates through the USB Micro-B port on the Transmier
• One-way Power over HDBaseT (PoH), so that the wall plate can be powered by receiver
• 1 x Wall Plate Transmier
• 1 x Wall Plate Plasc Panel
(2‐Gang US, with Screws)
• 1 x USB-B to A Cable
• 1 x Phoenix Male Connector
(3.5mm, 4 Pins)
• 4 x Mounng Screws
• 1 x Manual
--
-
Warnings:
• Before wiring, disconnect the power from the device.
• During wiring, connect and disconnect the cables gently.
Steps for device wiring:
1. Connect HDBT: Connect HDBT OUT of the transmier to
HDBT IN of an HDBT receiver via a Cat 5e/6/6a/7 cable.
2. Connect an HDMI display and USB devices to the receiver.
3. Connect power adapter to the receiver.
4. Connect the video sources and USB host device to the
transmier.
5. Select a desired video source through automac or manual
switching funcon.
--
-
The transmier oers automac switching funcon.
The automac switching funcon follows the Last-In-First-Out rule. For example, if a new acve source is connected, the transmier will
automacally switch to this source. If the source selected is removed, the transmier will automacally switch to the source with top priority
(default priority: USB-C > HDMI 1 > HDMI 2).
If you want the display to play video from a specic video source:
1. Disconnect the cable from your desired video source, and then connect it again.
2. Use the Input Selecon buon on the front panel or API commands to select your desired video source.
Note: The automac switching funcon can detect the input signal with 5V only. If the selected source in standby mode provides a connuous 5V
power output, this funcon will not work, i.e. the transmier will not switch the input to other acve sources. In this case, please turn o the
selected source in standby mode or remove it from the transmier.
--
-
--
-
Advanced users can control the transmier via API command through UPDATE port: connect a
control PC to the UPDATE port of the transmier (see the following gure). API command for
device control is available in the separate document “API Command Set_C2G31019”. A
professional RS232 serial interface soware (e.g. Serial Assist) may be needed as well.
Before sending the API command to control the transmier, ensure the transmier and control
PC are congured correctly.
This product supports rmware upgrading through Micro USB port. Please contact your supplier to get the latest upgrade tool “Legrand Product
Firmware Updater”.
Note：Don’t power o the device during upgrade process.
Steps to upgrade FW:
1. Connect the Micro USB port of the device to a PC.
2. Connect the power adapter provided to the device, and power on the device.
3. Click to run the “Legrand Product Firmware Updater” soware. The following window will appear on the next page:
--
-
“”:
•
•
• “”
•
“”
•
•
•
•
--
-
“” “”
’
Inhaltsverzeichnis
Sprachen:
Andere LEGRAND Sender Handbücher
LEGRAND
LEGRAND C2G 30019 Bedienungsanleitung
LEGRAND
LEGRAND C2G C2G30014 Bedienungsanleitung
LEGRAND
LEGRAND C2G30030 Bedienungsanleitung
LEGRAND
LEGRAND C2G RapidRun 60218 Bedienungsanleitung
LEGRAND
LEGRAND Tynetec ZXT870 Bedienungsanleitung
LEGRAND
LEGRAND MY HOME 883 31 Bedienungsanleitung
LEGRAND
LEGRAND C2G31030 Bedienungsanleitung
LEGRAND
LEGRAND 412006 Bedienungsanleitung
Beliebte Sender Handbücher anderer Marken
Dejero
Dejero EnGo 3x Bedienungsanleitung
Rosemount
Rosemount 4600 Bedienungsanleitung
Speaka Professional
Speaka Professional 2342740 Bedienungsanleitung
trubomat
trubomat GAB 1000 Bedienungsanleitung
Teledyne Analytical Instruments
Teledyne Analytical Instruments LXT-380 Bedienungsanleitung
Rondish
Rondish UT-11 Bedienungsanleitung
