Leister Unifloor E Bedienungsanleitung
1
LEISTER Unifloor E
Automatic hot air welding machine
Please read the operating instructions carefully before use
and keep for future reference.
GB
OPERATING INSTRUCTIONS
LEISTER Unifloor E
Flooring Automatic Welding Machine
• Welding of PVC coverings and melt welding of linoleum floor coverings.
APPLICATION
®
LEISTER Process Technologies, Riedstrasse, CH-6060 Sarnen/Switzerland
Tel. +41 41 662 74 74 Fax +41 41 662 74 16
www.leister.com [email protected]
Voltage V~
Frequency Hz
Capacity W
Temperature °C
Air flow (50-100%) l/min.
Drive speed m/min.
Noise emission level
LpA(dB)
Dimensions mm
Weight kg
TECHNICAL DATA
230 120 100
50 / 60 50 / 60 50 / 60
2300 1800 1500
20 – 620 20 – 620 20 – 620
max. 300 max. 250 max. 250
1.0 – 7.5 1.0 – 7.5 1.0 – 7.5
67 65 65
420×270×215 420×270 ×215 420×270 ×215
14 14 14
Mains voltage is not reversible
CCA certified
Protection Class I
Danger! Unplug the tool before opening it, as live compo-
nents and connections are exposed.
Incorrect use of hot air tools can present a fire and explosion
hazard, particularly in the proximity of flammable materials
and explosive gases.
The tool must be operated under supervision.
Heat can ignite flammable materials which are not in view.
For personal protection, we strongly recommend the tool to
be connected to an RCCB (Residual Current Circuit Breaker)
before using it on construction sites.
The rated voltage stated on the tool must correspond with
the mains voltage.
Danger of getting burned! Do not touch the heater tube and
nozzle when they are hot. Let the tool cool down. Do not
point the hot air flow in the direction of people or animals.
Protect the tool from damp and wet.
FI
230
120
WARNING
CAUTION
Only connect the tool to a receptacle with protective earth
conductor. Any disconnection of the protective earth
conductor, in or outside the tool is dangerous!
Only use extension lead with protective earth conductor.
Approval Marks
2
3
TOOL DESCRIPTION LEISTER Unfloor E
2
34
10
11
7
6
19
5
23 22
Main components
1. Housing
2. Mains cable
3. Hot air blower
4. Welding nozzle
5. Connection hose
6. Welding rod pressure roller
7. Drive roller
8. Chassis
9. Wall switch-off
10. Air filter
11. Manual air vane
12. Display
12
18
17
16
15
14 1
Operating components
14. Main switch
15. Drive switch
16. Potentiometer for welding speed
17. Potentiometer for air flow
18. Potentiometer for air temperature
19. Swivel lever
Steering equipment
20. Welding rod guide tube
21. Guide roller
Automatic drive
22. Switch pin
23. Set screw
20
21
8
9
4
OPERATION LEISTER Unifloor E
Operational condition: Accessories
• If the welding rod de-reeler (24) and lifting device (26) are available:
– Attach welding rod de-reeler (24) to the Unifloor E tool using cheese
head screw M8
×
20 (25).
– Attach lifting device (26) to the tool using socket head cap screw M6
×
30 (27).
Operating condition
• Check the nozzle setting: the nozzle must be positioned at a distance of about 2 -
3 mm from the floor cover and welding rod.
• When welding linoleum, lower the cover (28) on to the welding nozzle (4) (see
Detail A).
• Automatic drive
Automatic drive is adjusted as required, depending on nozzle position, by
means of switch pin (22) and set screw (23).
• Connect tool to the mains. Mains voltage must correspond with the voltage
rating stated on the tool.
• Switch on tool using main switch (14). Hot air blower (3) starts automatically.
• Important: under voltage
If the maximum temperature is not reached, reduce the airflow by means of
the manual air vane (11) and potentiometer for air flow (17).
Accessories
Welding rod de-reeler
Detail A
Accessories
Lifting device
25
2726
13
24
428
Cover open
428
Cover closed
OPERATION LEISTER Unifloor E
5
Welding procedure
• Swivel hot air blower (3) up to the stop using swivel lever (19). The welding process
starts automatically via automatic drive.
• If necessary, the tool can be started manually by means of the drive switch (15).
• Check the welding process: – Guide roller (21) must run in the joint.
– The welding bead must be visible. Adjust welding
parameters using the potentiometers (16), (17)
and (18) if necessary.
• Wall switch-off (9)
When contact with the wall, is made drive and heater are switched off automati-
cally.
• After finishing welding swing up the hot air blower (3) to the stop using swivel lever
(19). The welding process stops automatically.
• After completing welding work, set potentiometer for air temperature (18) to zero
so that hot air blower (3) cools down.
• Switch off the tool at the main switch (14).
• Disconnect the tool from the mains.
Tool positioning
• Swivel hot air blower (3), using swivel lever (19) up to the stop.
• Operate lifting device (26) by means of lifting device lever (13) so that welding rod
pressure roller (6) and drive roller (7) are at no-load.
• Position automatic welding machine over the joint to be welded.
• Insert welding rod through welding rod guide tube (20) and pull under the welding
rod pressure roller (6) and place it in the joint.
• The guide roller (21) must run in the welding joint.
• Activate lifting device (26) by means of lifting device lever (13) so that the auto-
matic welding machine is ready to start.
Welding parameters
• Set potentiometer for welding speed (16) to required value.
• Set potentiometer for air flow (17) to required value.
• Set potentiometer for air temperature (18) to required value.
• The pressure derives from the actual weight of the automatic hot air welding
machine.
Speed m/ft
Air-Vol %
ON Speed Air-Vol % Temperature
Temperature
(14) Main switch
Temperature ACTUAL-value
Display (12)
Temperature SET-value
Potentiometer for welding speed (16)
Potentiometer for air flow (17)
Potentiometer for air temperature (18)
Welding speed
Airflow
(15) Drive switch
BA Unifloor E/ 10.02
• Only LEISTER accessories should be used.
•Welding rod de-reeler (24)
•Lifting device (26)
• LEISTER Process Technologies and its authorised Service Centres offer free welding
courses and training.
• Clean the tool's air filter (10) with a brush when dirty.
• Clean welding nozzle (4) with wire brush.
• Check mains cable (2) and plug for electrical and mechanical damage.
• Have your Service Centre check the motor brushes after about 1,000 hours of
operation.
• Repairs should only be carried out by authorised LEISTER Service Centres. They
guarantee a correct and reliable repair service within 24 hours using original
spare parts in accordance with the circuit diagrams and spare parts lists.
• Guarantee and liability are in accordance with the guarantee certificate as well
as with the currently valid general business and sales conditions.
• LEISTER Process Technologies rejects any guarantee claims for tools which are not
in their original condition. The tools must never be altered or changed.
Technical data and specifications are subject to change without prior notice.
Your authorized Service Centre is:
GUARANTEE AND LIABILITY
SERVICE AND REPAIR
MAINTENANCE
TRAINING
ACCESSORIES
LEISTER Process Technologies, Riedstrasse, CH-6060 Sarnen/Switzerland
Tel. +41 41 662 74 74 Fax +41 41 662 74 16
www.leister.com [email protected]
6
®
Service Record LEISTER Unifloor E
®
LEISTER Process Technologies, Riedstrasse, CH-6060 Sarnen/Switzerland
Tel. +41 41 662 74 74 Fax +41 41 662 74 16
www.leister.com [email protected]
This document should be handed to the authorised LEISTER Service Center for
updating when repaired or serviced. This document is to be retained and kept
by the owner of the tool.
Technical Data
Automatic hot air welding machine Type
Order Number
Serial Number
Rated Voltage V
Ratet Power W
Sold Date
Service
1. Date Service Centre Signature
2. Date Service Centre Signature
3. Date Service Centre Signature
4. Date Service Centre Signature
5. Date Service Centre Signature
6. Date Service Centre Signature
Repair
1. Date Service Centre Signature
2. Date Service Centre Signature
3. Date Service Centre Signature
LEISTER Process Technologies, Riedstrasse, CH-6060 Sarnen/Switzerland
Tel. +41 41 662 74 74 Fax +41 41 662 74 16
www.leister.com [email protected]
®
Andere Handbücher für Unifloor E
1
Inhaltsverzeichnis
Andere Leister Schweißsystem Handbücher
Leister
Leister UNIROOF E 40 mm Bedienungsanleitung
Leister
Leister TRIAC ST Bedienungsanleitung
Leister
Leister ALLIED VARIMAT V2 Bedienungsanleitung
Leister
Leister UNIPLAN S Bedienungsanleitung
Leister
Leister TWINNY T7 Bedienungsanleitung
Leister
Leister EXAMO 100 Bedienungsanleitung
Leister
Leister Uniroof E Bedienungsanleitung
Leister
Leister WELDPLAST S2 Bedienungsanleitung
Leister
Leister UNIFLOOR 500 Bedienungsanleitung
Leister
Leister VARIANT T1 Bedienungsanleitung
Leister
Leister Comet 700 Bedienungsanleitung
Leister
Leister TWINMAT Bedienungsanleitung
Leister
Leister Uniplan E Bedienungsanleitung
Leister
Leister Twinny T Bedienungsanleitung
Leister
Leister WELDPLAST S2 Bedienungsanleitung
Leister
Leister VARIANT T1 Bedienungsanleitung
Leister
Leister AIRSTREAM 100 Bedienungsanleitung
Leister
Leister COMET Bedienungsanleitung
Leister
Leister WELDPLAST S1 Bedienungsanleitung
Leister
Leister Uniroof E Bedienungsanleitung
Beliebte Schweißsystem Handbücher anderer Marken
TAFA
TAFA 30*8B35 Bedienungsanleitung
Lincoln Electric
Lincoln Electric INVERTEC V350-PRO CE Bedienungsanleitung
ESAB
ESAB Buddy Arc 145 Bedienungsanleitung
CIGWELD
CIGWELD 636804 Kurzanleitung
Red-D-Arc
Red-D-Arc DC-400 Bedienungsanleitung
Hobart Welding Products
Hobart Welding Products Spool Gun DP 3035-10 Bedienungsanleitung
