LENCO PODO-152 Bedienungsanleitung

USER’S MANUAL

PODO-152

Media Player with Pedometer

For information and support, www.lenco.com

WARNINGS

•Do not place naked flames, such as lighted candles on or near the product.

•Do not place objects filled with liquids, such as vases on or near the product.

•Do not use or store this product in a place where it is subject to direct sunlight, heat,

excessive dust or vibration.

•Do not use this product with wet hands.

•Do not clean this product with water or other liquids.

•Do not block or cover the slots and holes in the product.

•Do not push foreign objects into the slots or holes in the product.

•Do not attempt to open this product yourself. There are no user serviceable parts

inside.

•Do not allow children access to plastic bags.

SAFETY WARNINGS

•Before using this product, read and follow all warnings and instructions.

•This product is not intended for use by young children. Young children should be

properly supervised.

•This product is intended for household use only and not for commercial or industrial

use.

•Do not expose to dripping or splashing.

•No naked flame sources, such as lighted candles, should be placed on the product.

•Ventilation should not be impeded by covering ventilation openings with items such

as newspapers, table cloths, curtains and the like.

•Make sure the unit is adjusted to a stable position. Damage caused by using this

product in an unstable position or by failure to follow any other warning or precaution

contained within this user manual will not be covered by warranty.

Lenco, suggests retaining the packaging in case for future transport of the product.

Prolonged exposure to loud sounds from personal music players may lead to

temporary or permanent hearing loss.

When participating in the traffic listening to a personal music player can make

the listener less aware of potential dangers such as approaching cars.

If at any time in the future you should need to dispose of this product please note that: All

batteries and accumulators need to be removed from this product (Removal of Waste

Batteries and Accumulators).

1. Get to know the controls on Player

Item

Description Item

Description

1 TFT Display 7 Mic Hole / Reset Switch Hole

2 Clip 8 (Previous / Fast-Backward)

3 (Volume Up) 9 (Next / Fast-Forward)

4 (Volume Down) 10 USB Mini Connector

5 Memory Card Slot 11 (Play / Pause / Standby ON -

OFF)

6 Earphone Output Jack 12 M(Menu / Enter / Select)

2. About Player Battery

Player has an internal, non-user-replaceable battery. For best results, the first time you

use player, let it charge for about 2 hours or until the battery status icon in the “Connect”

screen shows that the battery is in full.

Battery is in full

Note: Player continues to use battery power after it’s been turned off, if unit isn’t used for a

while, the battery might need to be charged. Recharging the player at least 2 – 3 times in

three months for maintain the battery life and performance.

a. Charging the Battery:

You can charge the player battery in two ways:

Connect player to your computer. Or,

Use the USB power charger. (not included)

b. Connection and Charging:

Once you have connected player with computer / power charger, then you will see the

“Connect” screen appear on screen,

The level bars are running in battery status icon at the “Connect” screen. The battery is

in charging.

“Connect” Screen

In Charging

Important: The battery does not charge when your computer is in sleep. The USB port on

most keyboards does not provide enough power to charge the player. Connect player to a

USB 2.0 port on your computer only to prevent charge problem.

3. Connecting and Disconnecting Player

You can connect the player with your computer to transfer those media files and

recorded voice memos when necessary, and to charge the battery.

a. To Connecting Player

To connect player to your computer, plug the connector of USB Cable into a USB port

on your computer, and connect the other end to player, then the “Connect” screen

appear for view.

Now the player is ready for media files transfer with your computer and the battery is

charging.

You can transfer the media files by using the computer mouse use drag and place, or

copy and paste, in between the player and your computer. Disconnect it when you’re

done.

b. To Disconnecting Player

It’s important not to disconnect player while it’s syncing or transferring files. Eject the

player before disconnect it.

To eject player, press and hold Mbutton for about 2 seconds, the “Connect” screen will

switch to “Main Menu” screen. And now is safe to disconnect the player with your

computer. Unplug the USB cable from the player. Or,

If you’re using a Windows PC, you can also eject player in My Computer or by clicking

the “Safely Remove Hardware” icon in the Windows system tray, select the

correspondence name of USB Device and choose “Stop” > choose “Confirm” > choose

“Confirm” follow by the pop up windows you’re your computer.

If you’re using a Mac, you can also eject player by dragging the player icon on the

desktop to the Trash.

Disconnect the USB cable from the player and computer, simply remove it.

If you accidentally disconnect player without ejecting it, reconnect it to your computer

and sync again. However, some media file may loss.

4. Getting Start the Player

Turn ON / OFF the player and use of Main Menu.

Press and hold button for 3 – 4 seconds to turn ON the player, then you will see

any one of the following shown Main Menu screen, Music / Movie / Record /

Pedometer / Voice / Photo / Setup / Game / eBook, will appear on LCD after the

Loading and Opening screen have displayed.

To turn OFF the player, press and hold the button for 3 – 4 seconds.

“Main Menu” screens

(If Music chooses) (If Movie chooses) (If Record chooses) (If Pedometer chooses)

(If Voice chooses) (If Photo chooses) (If Setup chooses) (If Game chooses)

(If eBook chooses)

5. Use Setup Menu

You might need to set date & time or change some default setting as you desired in

setup sub menu before you start to use the player.

To go into setup menu, from main menu, choose “Setup” by use / button and

then press M button, a “Setup” menu appears to use.

You can go back to previous menu by press the button during in setup menu. Or,

press and hold the Mbutton to return to main menu.

Setup Menu

(Menu Page 1) (Menu Page 2)

a. To Setup “System time” (Date & Time):

Choose “System time” by using / button and then press M button, a date &

time setting screen appears to use.

Press “+” button, the year is highlighted then adjusting to current year by pressing the

/ button. And repeating the adjusting methods by “+” and / button

again for finished those items; Month, Date, Hour, Minute and seconds setting

adjustment.

Finally, you need to press the M button to confirm the adjustment and back to Setup

menu, if not the date & time will not to memorize and you need to adjust them again.

b. To change “LCD set”

You can set the backlight to illuminate the screen for a certain amount of time as you

desired or make the backlight to always ON when every time you turn ON the player.

To change LCD backlight, choose “LCD set” > choose “Dark mode”, a level bar with

number appear then chose “0 (always On) / 5 / 10 / 15 / 20 / 25 / 30 / 35 / 40 / 45 / 50

(seconds)” as you desired by using Mand / buttons. Choose “0” to prevent

the LCD backlight from turning to off. (choosing this option decrease battery

performance)

c. To Change “Language”

This player can use difference OSD languages.

To set the language, choose “Language”, and then choose which language as you

desired by using M and / buttons.

d. To Set “Power Off”

The Power Off setting can extend the time between battery charges by turning OFF the

player when you are not using the controls or no operation. Also, Sleep function provided

for more choice.

To set power off time, choose “Power off”, then choose “Off time”, a levels bar with

number menu appear, then choose “0 - 200 seconds” as you want by using M and

/ buttons.

To set sleep time, choose “Power off”, then choose “Sleep time”, a levels bar with

number menu appear, choose “0 / 10 / 20 /30 / 40 / 50 / 60 / 70 / 80 / 90 / 100 / 110 /

120 minutes” as you want by using Mand / buttons.

e. To View “Memory info”

You can view about the memory status of player, such as the numbers of remaining

memory space available and the percentage of memory have used.

To view the status, choose “Memory info” by using Mand / buttons. An

information screen, remaining memory space available and percentage of memory

used, appear for view.

To return to setup menu or main menu press button or press and hold Mbutton

f. To View “Firmware Version”

You might need to view the details about firmware information inside the Player.

Choose “Firmware version” by using M and / buttons, an information

screen appear for view.

To return to setup menu or main menu, press button or press and hold Mbutton.

g. To “Exit”

Select Exit to back to main menu. Or, press and hold the Mbutton to go back main

menu.

6. Use Music Menu

You can use music player to playback with supported music file format of audio coding;

WMA and MP3 are supported by the player. To open the music player in Main Menu:

From main menu, choose “Music” by using / and Mbutton, a “Music Now

Playing” screen appears to use.

“Music Now Playing” Screen

a. To Play Music

In Music Now Playing screen, press button to start the play.

Press button to pause the playing music. Press it again to play.

b. Play Previous or Next Music

Press button to play next music.

Press button to play previous music.

c. Use Fast-Forward or Fast-Backward

Press and hold button to use fast-forward

Press and hold button to use fast-backward.

d. Adjust volume level

In music playing, press or pressing button to increase the volume levels, a change

volume control screen appears to view.

In music playing, press or pressing button to decrease the volume levels, a change

volume control screen appears to view.

Wait for 6 – 8 seconds or press button to return to music now playing screen.

For hearing protection; a beep warning will be heard from earphone, or display warning

pop-up on TFT screen, when every time you increase the volume level and reach to the

default setting level which may exceed 85dB. Press M button to accept the warning and

enter into the volume control for increase the level and until to maximum level.

e. Use Lyric Display

This player supports “*.LRC” lyric files and lyrics can synchronous displayed while

playing music if you music has lyric included. How to know whether the lyrics exist? If the

current song has matching lyric files, the color dot beside the Lyric Message icon will be

turned to green color from red in Music Now Playing screen.

Playing the music with lyrics, and then press and hold Mbutton to enter the lyric display

mode and the lyrics is displaying and moving up accordingly with the playing music.

Press M button to cancel the lyrics display and go back to Music Now Play screen if

you want.

7. Use Music Submenu in Music Stop Mode

You might need to selecting folders for music play and delete music files. To do this:

a. Local Folder

In Music Now Playing screen, press button to stop the playing music if player is in

playing, then press M button to call up the Music Submenu.

In Music Submenu screen, choose “Local folder” a list menu appear, and then select

folder and / or choose a music file by using / and M button.

It will go back to music now playing screen once a music file is selected. Then press

button to play.

b. Delete file

In Music Submenu screen, choose “Delete file” a list menu appear, and then choose

which music file that you want to delete by using / and M buttons.

Once file is selected, press Mbutton and choose Yes to confirm or No to cancel.

c. Delete All

In Music Submenu screen, choose “Delete all” then selects “Yes / No” by using /

button.

One “YES” or “NO” appear then press M button to confirm.

All music files will be deleted once YES is selected and confirmed, a “Deleting” screen

appear for a while and deleting process is in progress, then “Empty disk!” message will

shown on screen for few seconds.

d. Exit

Select Exit to back to music now playing screen.

8. Use Music Submenu in Music Playing Mode

You might need to do some changes for music playing, such as repeat, EQ settings for

music files… etc. To change setting:

a. To Set Repeat

In music playing mode, press Mbutton, a Music Submenu appear, then choose

“Repeat”, then choose “Normal / Repeat one / Folder / Repeat folder / Repeat all /

Random / Intro” as you desired by using / and Mbuttons.

b. To Change Equalizer

In music playing mode, press Mbutton, a Music Submenu appear, the choose

“Equalizer”, then choose “Natural / Rock / Pop / Classic / Soft / Jazz / DBB” as you

desired.

c. Exit

Select Exit to back to music now playing screen.

9. Use Movie Menu

a. To Play Movie

From Main Menu, choose “Movie” by using / and M button, a “Movie Now

Playing” screen appears to use.

In Movie Now Playing” screen, press key to start the play.

Press button to pause and to back to Movie Now Playing screen. Press it again,

the video will play continue.

b. To Play Previous or Next Video

Press button to play next movie file.

Press button to play previous movie file.

c. Use Fast-Forward or Fast-Backward

Press and hold button to play fast-forward.

Press and hold button to play fast-backward.

d. Adjust Volume Level

In movie playing, press or pressing button to increase the volume levels.

In movie playing, press or pressing button to decrease the volume levels.

To preset the volume level at movie stop mode, in Movie Now Playing screen press

/ key to preset your desired volume levels, a volume control screen appears to

view. Press / Mbutton to return to Movie Now Playing.

For hearing protection; a beep warning will be heard from earphone, or display warning

pop-up on TFT screen, when every time you increase the volume level and reach to the

default setting level which may exceed 85dB. Press M button to accept the warning and

enter into the volume control for increase the level and until to maximum level.

10. Use Movie Submenu

You might need to selecting folders, delete movie files and set repeat for movie play.

you can make change during in the playing mode at Movie Now playing screen

To do this:

In “Movie Now Playing” screen, press Mbutton to enter to movie submenu.

a. Local Folder

In movie submenu screen, choose “Local Folder”, a file list menu appear, and then select

folder and / or choose a desired movie file to play by using / and M button.

It will go back to music now playing screen once a music file is selected. Then press

button to play.

b. Delete File

In movie submenu screen, choose “Delete file” a file list menu appear, and then choose which

movie file that you want to delete by using / buttons.

Andere Handbücher für PODO-152

Inhaltsverzeichnis

Andere LENCO MP3-Player Handbücher

LENCO

LENCO XEMIO-250 Bedienungsanleitung

LENCO

LENCO Xemio-653 Bedienungsanleitung

LENCO

LENCO Xemio-861BU Bedienungsanleitung

LENCO

LENCO XEMIO-654 Bedienungsanleitung

LENCO

LENCO XEMIO-106 Bedienungsanleitung

LENCO

LENCO Xemio-768 Bedienungsanleitung

LENCO

LENCO SCD-651 Bedienungsanleitung

LENCO

LENCO SCD-50 BT Bedienungsanleitung

LENCO

LENCO Xemio-154GY Bedienungsanleitung

LENCO

LENCO XEMIO-125 Bedienungsanleitung

LENCO

LENCO XEMIO-200 Bedienungsanleitung

LENCO

LENCO Xemio-668 Bedienungsanleitung

LENCO

LENCO Xemio-645 Bedienungsanleitung

LENCO

LENCO XEMIO-654 Bedienungsanleitung

LENCO

LENCO XEMIO-106 Bedienungsanleitung

LENCO

LENCO XEMIO-360 W Bedienungsanleitung

LENCO

LENCO Xemio-861 Bedienungsanleitung

LENCO

LENCO PODO-151 Bedienungsanleitung

LENCO

LENCO Xemio-767 BT Bedienungsanleitung

LENCO

LENCO Xemio-768 Bedienungsanleitung

LENCO

LENCO Xemio-769GY Bedienungsanleitung

LENCO

LENCO XEMIO-633 Bedienungsanleitung

LENCO

LENCO Xemio-656 Bedienungsanleitung

LENCO

LENCO MP CARD Bedienungsanleitung

Beliebte MP3-Player Handbücher anderer Marken

Blaupunkt

Blaupunkt Compact Drive MP3 Bedienungsanleitung

Memorex

Memorex MMP9008 - 8GB USB 2.0 Bedienungsanleitung

Meizu Electronic Technology

Meizu Electronic Technology E5 Bedienungsanleitung

Naxa

Naxa NMV-173NX Bedienungsanleitung

Philips

Philips PSA250 Bedienungsanleitung

Zipy

Zipy go! Waving Bedienungsanleitung

Sylvania

Sylvania SMPK4068 Bedienungsanleitung

Sony

Sony NW-MS7 - Memory Stick Walkman Bedienungsanleitung

Irradio

Irradio RF-42UC Bedienungsanleitung

NABAIJI

NABAIJI SWIM MUSIC 100 Bedienungsanleitung

Laser

Laser MP3-A9-4GB Bedienungsanleitung

Samsung

Samsung YP-T7F Bedienungsanleitung

Savant

Savant SMS-1001-00 Kurzanleitung

Trevi

Trevi XP 71 BT Bedienungsanleitung

AGPtek

AGPtek C2 Bedienungsanleitung

MobiBlu

MobiBlu DAH-1500i Bedienungsanleitung

Denver

Denver MPS-201 Bedienungsanleitung

Steren

Steren MP3-002 Bedienungsanleitung