LENCO Xemio-653 Bedienungsanleitung

USER’S MANUAL

Xemio-653

Media Player

For information and support, www.lenco.com

Warnings

Don’ts

•Do not place naked flames, such as lighted candles on or near the product.

•Do not place objects filled with liquids, such as vases on or near the product.

•Do not use or store this product in a place where it is subject to direct sunlight, heat, excessive dust or

vibration.

•Do not use this product with wet hands.

•Do not clean this product with water or other liquids.

•Do not block or cover the slots and holes in the product.

•Do not push foreign objects into the slots or holes in the product.

•Do not attempt to open this product yourself. There are no user serviceable parts inside.

•Do not allow children access to plastic bags.

SAFETY WARNINGS

•Before using this product, read and follow all warnings and instructions.

•This product is not intended for use by young children. Young children should be properly supervised.

•This product is intended for household use only and not for commercial or industrial use.

•Do not expose to dripping or splashing.

•No naked flame sources, such as lighted candles, should be placed on the product.

•Ventilation should not be impeded by covering ventilation openings with items such as newspapers,

table cloths, curtains and the like.

•Make sure the unit is adjusted to a stable position. Damage caused by using this product in an

unstable position or by failure to follow any other warning or precaution contained within this user

manual will not be covered by warranty.

Lenco suggests retaining the packaging in case for future transport of the product.

If at any time in the future you should need to dispose of this product please note that: All batteries and

accumulators need to be removed from this product (Removal of Waste Batteries and Accumulators).

WARNING: Prolonged exposure to loud sounds from personal music players may lead to temporary

or permanent hearing loss.

WARNING: When participating in the traffic listening to a personal music player can make

the listener less aware of potential dangers such as approaching cars.

1. Get to know the controls on Player

About Player Battery

Player has an internal, non–user-replaceable battery. For best results, the first time you use

player, let it charge for about 2 hours or until the battery status icon in the “Connect” screen shows

that the battery is in full.

Battery is in full

Item Description Item Description

1 (Previous / Fast-Rewind / VOL-) 7 Microphone (Mono)

2 (Next / Fast-Forward / VOL+) 8 Earphone Output Jack

3 M(Menu / Enter / Select) 9 USB Mini Connector

4 (Play / Pause / Standby ON - OFF) 10 Micro SD Memory Card Slot

5 VOL (Volume Control) 11 TFT LCD Display

6 Main Power Switch (ON - OFF)

Note: Player continues to use battery power after it’s been turned off, if unit isn’t used for a while,

the battery might need to be charged.

a. Charging the Battery:

You can charge the player battery in two ways:

Connect player to your computer. Or,

Use the USB power charger. (available separately)

b. Connection and Charging:

Once you have connected player with computer / power charger, then you will see the

“Connect” screen appear on screen,

The level bars are running in battery status icon at the “Connect” screen. The battery is in

charging.

“Connect” Screen

In Charging

Important: The battery does not charge when your computer is in sleep. The USB port on most

keyboards does not provide enough power to charge the player. Connect player to a USB 2.0 port

on your computer only to prevent charge problem.

2. Connecting and Disconnecting Player

You can connect the player with your computer to transfer those media files and recorded

voice memos when necessary, and to charge the battery. Disconnect the player when you’re done.

a. To Connecting Player

To connect player to your computer, plug the connector of USB Cable into a USB port on your

computer, and connect the other end to player, then the “Connect” screen appear for view.

Now the player is ready for media files transfer with your computer and the battery is

charging.

You can transfer the media files by using the computer mouse use drag and place, or copy and

paste, in between the player and your computer. Disconnect it when you’re done.

b. To Disconnecting Player

It’s important not to disconnect player while it’s syncing or transferring files. Eject the player

before disconnect it.

To eject player, press and hold Mbutton for about 2 seconds, the “Connect” screen will switch

to “Main Menu” screen. And now is safe to disconnect the player with your computer. Unplug

the USB cable from the player. Or,

If you’re using a Windows PC, you can also eject player in My Computer or by clicking the

“Safely Remove Hardware” icon in the Windows system tray, select the correspondence name

of USB Device and choose “Stop” > choose “Confirm” > choose “Confirm” follow by the pop

up windows you’re your computer.

If you’re using a Mac, you can also eject player by dragging the player icon on the desktop to

the Trash.

Disconnect the USB cable from the player and computer, simply remove it.

If you accidentally disconnect player without ejecting it, reconnect it to your computer and

sync again. However, some media file may loss.

3. Getting Start the Player

Turn ON / OFF the player and use of Main Menu.

Slide the power switch to “ON” position, then you will see any one of the following shown

Main Menu screen, Music / Movie / Record / Voice / Photo / eBook / Game / Setup, will

appear on LCD after the Loading and Opening screen have displayed.

To standby OFF the player, press and hold the button for 3 – 4 seconds.

To turn ON the player again, press and hold the button for 3 – 4 seconds again.

“Main Menu” screens

(If Music chooses) (If Movie chooses) (If Record chooses) (If Play chooses)

(If Picture chooses) (If Text chooses) (If Game chooses) (If Setting chooses)

4. Use Setup Menu

You might need to set date & time or change some default setting as you desired in setup sub

menu before you start to use the player.

To go into setup menu, from main menu, choose “Setup” by use / button and then

press M button, a “Setting” menu appears to use.

You can go back to previous menu by press the button during in setup menu. Or, press and

hold the Mbutton to return to main menu.

Setup Menu

(Menu Page 1) (Menu Page 2)

a. To Setup “System time” (Date & Time):

Choose “System time” by using / button and then press M button, a date & time

setting screen appears to use.

Press “VOL” button, the year is highlighted then adjusting to current year by pressing the

/ button. And repeating the adjusting methods by “VOL” and / button again

for finished those items; Month, Date, Hour, Minute and seconds setting adjustment.

Finally, you need to press the M button to confirm the adjustment and back to Setup menu, if

not the date & time will not to memorize and you need to adjust them again.

Important: Don’t turn OFF the player by the Power Switch if you want to keep the date & time

running in background, standby OFF the player by press and hold the button in this case. If not,

the set date & time will be losses. Adjust the clock again if you want it to use.

b. To change “LCD set”

You can set the backlight to illuminate the screen for a certain amount of time as you desired

or make the backlight to always ON when every time you turn ON the player.

To change LCD backlight, choose “LCD set” > choose “Dark mode”, a level bar with number

appear then chose “0 (always On) / 5 / 10 / 15 / 20 / 25 / 30 / 35 / 40 / 45 / 50 seconds” as you

desired by using Mand / buttons. Choose “0” to prevent the LCD backlight from

turning to off. (choosing this option decrease battery performance)

c. To Change “Language”

This player can use difference OSD languages.

To set the language, choose “Language”, and then choose which language as you desired by

using M and / buttons.

d. To Set “Power Off”

The Power Off setting can extend the time between battery charges by turning OFF the player

when you are not using the controls or no operation. Also, Sleep function provided for more choice.

To set power off time, choose “Power off”, then choose “Off time”, a levels bar with number

menu appear, then choose “0 - 200 seconds” as you want by using M and / buttons.

To set sleep time, choose “Power off”, then choose “Sleep time”, a levels bar with number

menu appear, choose “0 / 10 / 20 /30 / 40 / 50 / 60 / 70 / 80 / 90 / 100 / 110 / 120 minutes” as

you want by using Mand / buttons.

e. To Change “Online mode” (Applicable depend on Model)

You might need to change the online mode when connecting with computer system. In the

sense that some operating systems (under Windows 2K SP4) cannot support two driver letters in

one USB disk. The multiply driver is selected by device default; however, you can change it when

necessary.

To change type of disk, choose “Online mode” choose “Multiply driver / Normal only (single

ordinary disk) / Card only” by using M and / buttons.

f. To View “Memory info”

You can view about the memory status of player, such as the numbers of remaining memory

space available and the percentage of memory have used.

To view the status, choose “Memory info” by using Mand / buttons. An

information screen, remaining memory space available and percentage of memory used,

appear for view.

To return to setup menu or main menu press button or press and hold Mbutton

g. To “Format Device”

You might need to format device the device memory. In some circumstances, the device

memory may be corrupted, or you may need to format the memory card if it newly use with this

device. However, you can format the device or memory card by the following method but all data

will be losses.

Choose “Format Device” then choose “Format Disk / Format Card” by using M and /

buttons, and then choose OK to process or choose Cancel to exit and back to setup menu.

h. To View “Firmware Version”

You might need to view the details about firmware information inside the Player.

Choose “Firmware version” by using M and / buttons, an information screen

appear for view.

To return to setup menu or main menu, press button or press and hold Mbutton.

i. To “Firmware Upgrade” (System Utility Tools required)

You might need to upgrade the firmware for advanced the player performance or firmware

getting trouble or damaged in some circumstance, such as electrostatic voltage discharge issue

happens. Please follow the instruction posted by the dealer (if any) or follow the instruction from

System Utility Tools if provided. It is not recommended to do if the player is proper working.

j. To “Exit”

Select Exit to back to main menu. Or, press and hold the Mbutton to go back main menu.

5. Use Music Menu

You can use music player to playback with supported music file format of audio coding; WAV

and MP3 are supported by the player. To open the music player in Main Menu:

From main menu, choose “Music” by using / and Mbutton, a “Music Now

Playing” screen appears to use.

“Music Now Playing” Screen

a. To Play Music

In Music Now Playing screen, press button to start the play.

Press button to pause the playing music. Press it again to play.

b. Play Previous or Next Music

Press button to play next music.

Press button to play previous music.

c. Use Fast-Forward or Fast-Backward

Press and hold button to use fast-forward

Press and hold button to use fast-backward.

d. Adjust volume level

In music playing , press “VOL” button, a change volume control screen appears, then press

/ buttons to adjust volume levels to down / up.

Wait for 6 – 8 seconds or press button to return to music now playing screen.

For hearing protection; a beep warning will be heard from earphone, or display warning pop-up

on TFT screen, when every time you increase the volume level and reach to the default setting level

which may exceed 85dB. Press M button to accept the warning and enter into the volume control

for increase the level and until to maximum level.

e. Use Lyric Display

This player supports “*.LRC” lyric files and lyrics can synchronous displayed while playing

music if you music has lyric included. How to know whether the lyrics exist? If the current song has

matching lyric files, the color dot beside the Lyric Message icon will be turned to green color

from red in Music Now Playing screen.

Playing the music with lyrics, and then press and hold Mbutton to enter the lyric display mode

and the lyrics is displaying and moving up accordingly with the playing music.

Press M button to cancel the lyrics display and go back to Music Now Play screen if you want.

6. Use Music Submenu in Music Stop Mode

You might need to selecting folders for music play and delete music files. To do this:

a. Local Folder

In Music Now Playing screen, press button to stop the playing music if player is in playing,

then press M button to call up the Music Submenu.

In Music Submenu screen, choose “Local folder” a list menu appear, and then select folder

and / or choose a music file by using / and M button.

It will go back to music now playing screen once a music file is selected. Then press

button to play.

b. Delete file

In Music Submenu screen, choose “Delete file” a list menu appear, and then choose which

music file that you want to delete by using / and M buttons.

Once file is selected, press Mbutton and choose Yes to confirm or No to cancel.

c. Delete All

In Music Submenu screen, choose “Delete all” then selects “Yes / No” by using /

button.

One “YES” or “NO” appear then press M button to confirm.

All music files will be deleted once YES is selected and confirmed, a “Deleting” screen appear

for a while and deleting process is in progress, then “Empty disk!” message will shown on

screen for few seconds.

d. Exit

Select Exit to back to music now playing screen.

7. Use Music Submenu in Music Playing Mode

You might need to do some changes for music playing, such as repeat, EQ settings for music

files… etc. To change setting:

a. To Set Repeat

In music playing mode, press Mbutton, a Music Submenu appear, then choose “Repeat”, then

choose “Normal / Repeat one / Folder / Repeat folder / Repeat all / Random / Intro” as you

desired by using / and Mbuttons.

b. To Change Equalizer

In music playing mode, press Mbutton, a Music Submenu appear, the choose “Equalizer”,

then choose “Natural / Rock / Pop / Classic / Soft / Jazz / DBB” as you desired.

c. To set Replay Mode

Set Repeat A-B:

In Music Submenu, press Mbutton, a list menu appear, then choose “Replay mode” then

choose “Repeat”, a letter “A” is flashing in Music Now Playing screen, then press button

to select the starting point of track “A”.

Then a letter “B” is flashing once “A” is selected, use button again to select the ending

point of track “B” which you want by using button. And now the A – B distance of track

is repeating.

However, the repeating time and the replay gap time is depend on the set values of Replay

Time and Replay Gap have mentioned in below items.

To create another A – B distance of track to repeat, press button again and then again. a

new created A – B distance of track is repeating.

To cancel the repeat A – B function, press the M button. Or press button to pause.

Set Replay Times:

In music playing mode, press Mbutton, a Music Sub-menu appear, the choose “Replay times”,

then choose “1 / 2 / 3 / 4 / 5 / 6 / 7 / 8 / 9 / 10” as you desired by using / and M

buttons. The Player will replay those music file as your selected number of times accordingly.

Andere Handbücher für Xemio-653

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere LENCO MP3-Player Handbücher

LENCO

LENCO XEMIO-360 W Bedienungsanleitung

LENCO

LENCO SCD-50 BT Bedienungsanleitung

LENCO

LENCO XEMIO-SPORT-232 Bedienungsanleitung

LENCO

LENCO SCD-39 USB Bedienungsanleitung

LENCO

LENCO Xemio-861BU Bedienungsanleitung

LENCO

LENCO Xemio-656 Bedienungsanleitung

LENCO

LENCO XEMIO-760 BT Bedienungsanleitung

LENCO

LENCO XEMIO-360 W Bedienungsanleitung

LENCO

LENCO Xemio-668 Bedienungsanleitung

LENCO

LENCO XEMIO-200 Bedienungsanleitung

LENCO

LENCO MP BLASTER SNOOPY Bedienungsanleitung

LENCO

LENCO Xemio-768 Bedienungsanleitung

LENCO

LENCO Xemio-241 Bedienungsanleitung

LENCO

LENCO XEMIO-119 Bedienungsanleitung

LENCO

LENCO Xemio-861 Bedienungsanleitung

LENCO

LENCO XEMIO-732 R Bedienungsanleitung

LENCO

LENCO Xemio-861 Bedienungsanleitung

LENCO

LENCO XEMIO-115 Bedienungsanleitung

LENCO

LENCO Xemio-769 Bedienungsanleitung

LENCO

LENCO XEMIO-119 Bedienungsanleitung

LENCO

LENCO XEMIO-SPORT-222 Bedienungsanleitung

LENCO

LENCO Xemio-560 Bedienungsanleitung

LENCO

LENCO XEMIO-955 Bedienungsanleitung

LENCO

LENCO XEMIO-106 Bedienungsanleitung

Beliebte MP3-Player Handbücher anderer Marken

Blaupunkt

Blaupunkt Compact Drive MP3 Bedienungsanleitung

Memorex

Memorex MMP9008 - 8GB USB 2.0 Bedienungsanleitung

Meizu Electronic Technology

Meizu Electronic Technology E5 Bedienungsanleitung

Naxa

Naxa NMV-173NX Bedienungsanleitung

Philips

Philips PSA250 Bedienungsanleitung

Zipy

Zipy go! Waving Bedienungsanleitung

Sylvania

Sylvania SMPK4068 Bedienungsanleitung

Sony

Sony NW-MS7 - Memory Stick Walkman Bedienungsanleitung

Irradio

Irradio RF-42UC Bedienungsanleitung

NABAIJI

NABAIJI SWIM MUSIC 100 Bedienungsanleitung

Laser

Laser MP3-A9-4GB Bedienungsanleitung

Samsung

Samsung YP-T7F Bedienungsanleitung

Savant

Savant SMS-1001-00 Kurzanleitung

Trevi

Trevi XP 71 BT Bedienungsanleitung

AGPtek

AGPtek C2 Bedienungsanleitung

MobiBlu

MobiBlu DAH-1500i Bedienungsanleitung

Denver

Denver MPS-201 Bedienungsanleitung

Steren

Steren MP3-002 Bedienungsanleitung