Lenovo SE350 Bedienungsanleitung

ThinkSystem Friction 2-Post Screw-in Rail Kit

Read guidelines first

Review the documentation that comes with the rack for safety and cabling information. Before you install the

server in a rack, read the following guidelines:

• Some illustrations might differ from your server. All types of server are removed and installed in a similar

manner.

• See the Maintenance Manual for the ma imum room air temperature.

• Do not block any air vents, usually 15 cm (6 inches) of air space provides proper airflow.

• Plan the device installation starting from the bottom of the rack.

• Install the heaviest device in the bottom of the rack.

• Do not e tend more than one device out of the rack at the same time.

• Do not place any objects on the top of the rack-mounted devices.

• Connect all power cords to properly wired and grounded electrical outlets.

• Do not overload the power outlet when installing multiple devices in the rack.

• The ma imum width of the mounting flange is 225.6 mm (8.9 inches).

Safety notice

CAUT ON:

Make sure the rails support your server model and use

safe practices when lifting

Rail Support Matrix

For the detailed information about the rail support, see the following website: https://en.resources.lenovo.com/

brochures/thinksystem-rail-support-matri

Part number

Find the rail part number on the label as shown, use the part number to identify your rail model in the Rail

Support Matri above.

1 Part number (10 digits)

The rail package contains the following items:

1 Document

2 Left rail

3 Right rail

4 Nine M5 screws (for square-hole and round-hole rack)

5 Nine cage nuts (for square-hole rack)

6 Nine clip nuts (for round-hole rack)

7 Nine 10-32 screws (for threaded rack)

8 Nine 12-24 screws (for threaded rack)

9 Four screws

nstallation steps

Remove nner Rails

Note: The graphic shown below is the right rail.

Step 1. Pull the inner rail outward until you see the release latch.

Step 2. Press the release latch.

Step 3. Pull out the inner rail away from the outer rail.

Step 4. Repeat step 1-3 on the left rail.

nstall nner Rails on System

Note: The graphic shown below is the right rail.

Step 1. Align the mounting holes in the inner rail with the corresponding rail mounting pins on the side of the server.

Step 2. Push the inner rail as shown until the mounting pins on the server lock into place with the inner rail.

Step 3. Repeat step 1-2 on the left rail.

Notes:

• Make sure the stamp “Front” always face toward the front when assembling the inner rail to the server or to the

slide-rail assembly.

• The number of the rail mounting pins on the side of the server might be different from the illustration depending on

the server model.

Step 4. Insert and fasten the four screws on the left and right rails if needed (depending on the server model).

Adjust the Position of the Sliding Brackets (optional)

Bracket position for different server depth:

1 Server depth: 480 mm-560 mm (default position)

2 Server depth: 675 mm-752 mm

3 Server depth: 700 mm-779 mm

4 Server depth: 725 mm-805 mm

Note: Based on the server dimension, you may need to adjust the bracket to make sure the center of gravity of the

server is within the rails. The steps are listed as below.

Step 1. Move rear sliding bracket to the back as shown.

Step 2. Pull the pins of front sliding bracket.

Step 3. Slide the front bracket so the pins lock into the corresponding holes on the rails.

nstall Nuts to Rack

Note: For threaded rack, skip to the ne t page for Step 5.

• For round-hole rack, install clip nuts to the rack as shown

1 Clip nut

• For square-hole rack, install cage nuts to the rack as shown

1 Cage nut

nstall Rails to Rack

Notes: The graphic shown below is the right rail.

Use the same method to install the rails to all types of racks:

• For square-hole rack, use M5 screws and cage nuts

• For round-hole rack, use M5 screws and clip nuts

• For threaded rack, use only 10-32 or 12-24 screws (depending on the rack)

Step 1. Align the rail with the rack and install the screws to secure the front side of the rail.

Step 2. Adjust the rear sliding bracket against the rack; then, install the screws to secure the rail.

Step 3. Repeat step 1-2 on the left rail.

1 Screws installation on the front side of the rack

2 Screws installation on the rear side of the rack

Slide System into Rails in Rack

Step 1. Carefully lift the server and align the server with the slide rails. Position the server as shown and push the

server into the rack.

Step 2. Press the release latches.

Step 3. Push the server all the way into the rack until the server locks into place with a click.

Tighten Front Screws (optional)

Secure the server before you move the rack or place the rack in a vibration-prone area. Open the rack release latches

and tighten the screws to firmly secure the system.

1 Rack release latches

2 Front Screw

1100

Andere Handbücher für SE350

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere Lenovo Server Handbücher

Lenovo

Lenovo ThinkServer TS200v Bedienungsanleitung

Lenovo

Lenovo ThinkServer TD200x Leitfaden

Lenovo

Lenovo ThinkServer RD330 Leitfaden

Lenovo

Lenovo x3100 M5 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR630 V3 Bedienungsanleitung

Lenovo

Lenovo ThinkServer TS200v Bedienungsanleitung

Lenovo

Lenovo ThinkServer Bedienungsanleitung

Lenovo

Lenovo ThinkServer TD200x Leitfaden

Lenovo

Lenovo 7D9E Bedienungsanleitung

Lenovo

Lenovo ThinkSERVER TS130 Leitfaden

Lenovo

Lenovo ThinkServer TD200 Bedienungsanleitung

Lenovo

Lenovo ThinkSystem SR850P Bedienungsanleitung

Lenovo

Lenovo ThinkServer RD530 Stücklistenhandbuch

Lenovo

Lenovo x3300 M4 7382 Montage- und Wartungsanleitung

Lenovo

Lenovo ThinkServer RD640 Betriebsanleitung

Lenovo

Lenovo x3755 M3 Bedienungsanleitung

Lenovo

Lenovo ThinkServer 3057 Bedienungsanleitung

Lenovo

Lenovo ThinkServer TD100 Bedienungsanleitung

Lenovo

Lenovo ThinkSERVER TS130 Leitfaden

Lenovo

Lenovo ThinkServer TS200v Bedienungsanleitung

Lenovo

Lenovo ThinkServer TS200v Leitfaden

Lenovo

Lenovo ThinkAgile HX2320 Appliance Bedienungsanleitung

Lenovo

Lenovo ThinkServer TS440 Bedienungsanleitung

Lenovo

Lenovo ThinkSERVER TS130 Leitfaden

Beliebte Server Handbücher anderer Marken

HP AlphaServer ES47 Bedienungsanleitung

Dell

Dell PowerEdge R410 Bedienungsanleitung

PowerNAS

PowerNAS CMA Bedienungsanleitung

Supero

Supero FatTwin F617R3-FT Bedienungsanleitung

MSI

MSI P1-109N-L70 Bedienungsanleitung

Dell

Dell PowerEdge XE9640 Handbuch

Dell

Dell PS4100 Montageanleitung

EtroVISION

EtroVISION EV3151 Bedienungsanleitung

NEC

NEC Express5800/T110j Bedienungsanleitung

HP ProLiant Gen9 Bedienungsanleitung

Compaq

Compaq ProLiant 3000 Handbuch

Dell

Dell PowerEdge 3YPMN Bedienungsanleitung

iRobo

iRobo IPC2U Bedienungsanleitung

Nortel

Nortel 1000 Con?guration guide Bedienungsanleitung

Asus

Asus AP7500 Bedienungs- und Wartungshandbuch

Avid Technology

Avid Technology AirSpeed 5000 Bedienungsanleitung

HP Integrity rx2600 Installationsanleitung

Milestone

Milestone Husky IVO 350T Bedienungsanleitung