LG CRD-8484B Bedienungsanleitung

CD-ROM DRIVE

MODEL : CRD-8484B

OWNER’S MANUAL

BEDIENUNGSHANDBUCH

MODE D’EMPLOI

MANUALE D’USO

MANUAL DE USUARIO

To enjoy fully all the features and functions of your CD-ROM Drive,

Please read this Owner’s Manual carefully and completely.

website ; http://www.LGEservice.com

e-mail ; http://www.LGEservice.com/techsup.html

Questo manuale include il tagliando

di garanzia. (pagina n. I-8)

E-2

This product is manufactured to comply with the radio interference requirements of EEC DIRECTIVE

89/336/EEC, 93/68/EEC and 73/23/EEC.

AUTION : The laser used in the CD-ROM drive can damage your eyes.

Do not attempt to open the cover.

To reduce the risk of electric shock, do not remove cover (or back).

No user-serviceable parts inside.

Refer servicing to qualified service personnel.

This unit uses CD-ROM discs

marked with this symbol:

Use of controls or performance of procedures other than those specified here in may result in hazardous radiation

exposure.

PRODUCT COMPLIES WITH DHHS

RULES 21 C.F.R. SUB-CHAPTER J,

IN EFFECT AT THE DATE OF MANUFACTURE.

WARNING : To reduce the risk of fire or electric shock,

do not expose this appliance to rain or moisture

FCC COMPLIANCE STATEMENT

Note : This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15

of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accor-

dance with the instructions, may cause harmful interference to radio communications. However, there is no guaran-

tee that interference will not occur in a particular installation. If this equipment does cause harmful interference to

radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged

to try to correct the interference by one or more of the

following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an Authorized Service Center for help.

• FCC WARNING

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s author-

ity to operate the equipment.

• This CD-ROM Drive is for use only with UL listed personal computers that have installation instructions

detailing user installation of card cage accessory.

COMPACT

Industry Canada requirement

This class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment

Regulations.

Cet appareil numérique de la classe B respecte toutes les exigences du Règlement sur le matériel brouilleur du

Canada.

English

E-3

DECLARATION OF CONFORMITY

This device complies with Part 15 of the FCC Rules. Operation

is subject to the following two conditions : (1) this device may

not cause harmful interference, and (2) this device must accept

any interference received, including interference that may cause

undesired operation.

Equipment Classification : FCC Class B Peripheral Device(JBP)

Type of Product (EUT) : CD-ROM Drive

Manufacturer: LG Electronics lnc.

Address: 19-1, Cheongho-Ri, Jinwuy-Myon

Pyungtaek-Shi, kyunggi-Do, 451-713 Korea

Attention: Mr. T.K.Lee - General Manager

Multimedia Standards Team

We hereby declare that the equipment bearing the trade and model

number specified above was tested conforming to the applicable FCC

Rules under the most accurate measurement standards possible, and

that all the necessary steps have been taken and are in force to assure

that production units of the same equipment will continue to comply

with the Commission’s requirements.

Trade Name/Model : LG or Goldstar/CRD-8484B

Responsible Party : LG Electronics U.S.A. Inc., Chicago office

Address : 6133 North River RD Suite 1100

Rosemont, IL. 60018, U.S.A.

Contact Person: Mr. P. H. Byun, General Manager

Tel. No. (847) 993-4529

English

E-4

Features

[E-IDE interface

[48X-speed Max 7200KB/sec data transfer rate

[75ms random access time

[Intelligent 128KB data buffering system

[Small CPU bandwidth (MPC spec.)

[Motorized tray loading system

[Horizontal/Vertical mounting support

[Designed for internal mounting

[Emergency eject support

[Easy audio CD control button support

[Supports Windows 95 & 98 Plug-and-Play ATAPI protocol

[Multimedia PC MPC compliant

[Photo CD multisession support

System Requirement*

[IBM PC AT or compatible, 486 SX 25 processor or higher

(Pentium 133 Processor or higher recommended).

[640 Kb memory (16Mb or higher recommended).

[A suitable free standard 51/4”internal drive bay.

[MS-DOS version 3.1 or higher. (Windows 95 and above recommended).

[31/2”1.44 Mb Floppy Drive.

[An existing IDE controller with an available cable connector or a new IDE

controller (recommended with IDE PIO Mode 4 capability) that you will need

to install.

*Please note: certain software (i.e. particularly those including Video

playback) may require an considerably increased specification PC to give

acceptable results.

E-5

Location and Function of Controls

COMPACT

12345 6 7

anneau arrière

125

Front View

Supplied Accessories

zzOwner’s Manual zzDevice Driver(MS-DOS) zzAudio Cable

Back View

E-6

Front View

1. Headphone Jack

Standard 1/8”(3.5mm) stereo jack for listening to the audio signal from audio CDs.

2. Headphone Volume Control

Adjusts the headphone sound level.

3. Disc Drawer

Accepts a CD-ROM disc on its tray.

4. Busy Indicator

The Busy Indicator lights during initialization and data-read operations.

5. Emergency Eject Hole

Insert a paper clip here to eject the drawer manually or when there is no

power.

6. Play/Skip Button

When an Audio CD is in the Disc Drawer, pressing this button will start

playing audio CDs from the first track. If an audio CD is playing, pressing this

button will skip to the next track.

7. Open/Close/Stop Button

This button is pressed to open or close the CD tray.

If an audio CD is playing, pressing this button will stop it, and pressing it

again will open the tray.

Back View

1. Digital Audio Output Connector

This is a digital audio output or Video CD output connector.

You can connect this to a digital audio system or a Video CD Board.

2. Analog Audio Output Connector

The Audio Output Connector connects to a sound card.

3. Master/Slave/CSEL Jumper

These three jumpers are used to set the CD-ROM Drive to either a Master,

Slave, or CSEL device.

4. Interface Connector

This 40-pin connector is used to transfer data and control signals between the CD-

ROM Drive and your PC.

5. Power-in Connector

Attach a power cable from the computer to this connector.

E-7

Installing the Drive

Before installing the drive, turn off the system power. Follow the steps below to

install the CD-ROM drive:

1. Remove the cover from your computer system. Refer to manual for the

computer for details about removing the cover.

2. Insert the CD-ROM drive unit into a free 5.25-inch drive bay. Secure the

CD-ROM drive to the drive bay rails with the mounting screws (supplied).

3. Connect the 4-pin power cable and 40-pin IDE interface cable to the back of

the CD-ROM drive.

Notes: If there is no spare power cable available in the computer, you will have

to purchase a splitter cable of a suitable type.

The red edge of the IDE cable corresponds to pin 1 of the IDE interface on the

CD-ROM drive.

Please Note: an IDE cable is not supplied and may be required to be purchased

separately.

If the computer is using a sound card, the drive is connected to the sound card

with an audio cable. This CD-ROM drive is supplied with a Creative Labs

SoundBlaster© compatible audio lead, if this is not suitable for your sound card,

it maybe necessary for you to purchase a suitable lead from your retailer. Refer

to the manual for the sound card for detailed information regarding connection.

Câble audio

Bande rouge

Câble

d’alimentation

Câble IDE

Audio Cable

IDE cable Red Strip

Power Cable

E-8

4. Adjust the Master/Slave jumpers on the back of the CD-ROM drive as

necessary.

Connect the CD-ROM drive to the IDE ports of your motherboard. In general,

the hard drive will be in Primary IDE port and Master device for booting the

operating system. There are two possible alternate connection for CD-ROM

drive installation.

A) When using a Primary IDE port

If you need to connect your CD-ROM drive to the same Primary IDE port, the

CD-ROM drive should be set to Slave position.

5. When the installation of the drive unit is complete, replace the computer

cover.

6. Reconnect the computer power cord and turn on the computer.

B) When using a Secondary IDE port

You can also connect CD-ROM drive to the Secondary IDE port and set to

Master position.

DIGITAL

AUDIO

DGGLCSM 391

R+5+12

GND

AUDIO

ANALOG

INTERFACEPOWER

DIGITAL

AUDIO

DGGLCSM391

R+5+12

GND

AUDIO

ANALOG

INTERFACEPOWER

DIGITAL

AUDIO

DGGLCSM391

R+5+12

GND

AUDIO

ANALOG

INTERFACEPOWER

Primary connector

Master drive

(Booting hard disk)

Slave drive

(CD-ROM drive)

Master drive

(Booting hard disk) Master drive

(CD-ROM drive)

Motherboard

Secondary connector

Primary connector

Slave drive

(Other IDE drive)

E-9

Device Drivers

When using Windows 95/98/2000 or Window NT Workstation Ver. 4.0, the

installation of any software driver or special device is not required.

This CD-ROM drive is supplied with MS-DOS drivers on a 31/2-inch floppy disk.

These drivers are required to use the CD-ROM drive in DOS and Windows 3.1.

Drivers for other Operating Systems are not normally required or available as

they usually have an generic IDE, E-IDE/ATAPI CD-ROM driver built in; Windows

95, 98, NT 3.51 and higher and OS/2 Warp 3.0 are such examples.

If it is necessary to edit any file manually, first make a backup copy on a floppy

disk, then edit the original file, save it to your hard drive, exit, and re-boot the

PC to ensure the change will be implemented.

Running the Install Program (MS-DOS Installation)

1. Insert the diskette into the appropriate drive with DOS booting.

2. Go to the floppy drive by typing A: or B: at the DOS prompt, as appropriate.

3. Type the word INSTALL and press [ENTER].

4. The INSTALL program will begin loading. When loading is complete, the

INSTALL program identification will appear on screen.

5. Follow the instructions on screen.

6. When installation is complete, remove the diskette and reboot your PC.

For Windows 95/98/2000 Users

[In order to ensure normal drive operation, please check the following:

•The drive is displayed in

Windows 95/98 : [Control Panels]-[System]-[Device Manager]-[CD-ROM]

Windows 2000 : [Control Panels]-[System]-[Hardware]-[Device Manager]-[DVD/CD-ROM-Drive]

•32-bit is displayed in

[control panels]-[system]-[performance]

[If the drive is not recognized by your computer, please check the following

items.

•If a indicator is displayed on the IDE controller in [control panels]-

[system]-[device manager]-[harddisk controller], you will need to contact

your PC’s manufacturer or the motherboard’s manufacturer and get the appropriate

IDE controller driver.

[Run ADD NEW HARDWARE in Control Panel to let PC search again for new

device.

E-10

For Windows NT Workstation Ver. 4.0 Users

[In order to ensure normal drive operation, please check the following:

•The drive is displayed on the IDE controller in

[control panels] - [SCSI adapter] - [devices]

[If the drive is not recognized by your computer, please check the following

items.

•If a indicator is displayed on the IDE controller in [control panels]-

[SCSI adapter]-[devices], you will need to contact your PC’s manufacturer

or the motherboard’s manufacturer and get the appropriate IDE controller

driver.

This drive has a function that allows the CD to be ejected manually if this

becomes necessary in an emergency, such as failure of the drive or a power

outage. Follow this procedure in such a case.

NOTE: Don’t use this feature except in an emergency.

1) Turn the power to OFF.

2) Poke a fine-tipped object (such as a straightened heavy duty paper clip) into

the small hole at the front. The front door will pop open and the disk tray will come

partway out.

3) Pull the front door to open it all the way, then grip the disc tray between

thumb and forefinger and gently pull it straight out.

NOTE: This feature is a last measure to be used only in an emergency. Using it

excessively will cause malfunction.

Emergency Eject

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere LG CD/CDR-Laufwerk Handbücher

LG CED-8120B - - CD-RW Drive Bedienungsanleitung

LG GCC-4480B Bedienungsanleitung

LG GGW-H10N Bedienungsanleitung

LG CRD-8481B Bedienungsanleitung

LG 8886 - Photosmart Camera Dock Digital Docking... Bedienungsanleitung

LG GCR-8521B Bedienungsanleitung

LG CRD-8480M Bedienungsanleitung

LG CRD-8322B Bedienungsanleitung

LG GCR-8522B Bedienungsanleitung

LG GCC-4241N Bedienungsanleitung

LG CRD-8522B Bedienungsanleitung

LG DRD-8120B Bedienungsanleitung

LG GCE-8400B Bedienungsanleitung

LG CED-8080B - - CD-RW Drive Bedienungsanleitung

LG CRD-8322B Bedienungsanleitung

LG CH12LS28 Bedienungsanleitung

LG GCE-8480B Bedienungsanleitung

LG CED-8083B - - CD-RW Drive Bedienungsanleitung

LG CRD-8320B Bedienungsanleitung

LG BH10LS30 Bedienungsanleitung

LG CRD-8483B Bedienungsanleitung

LG GCE-8320B Bedienungsanleitung

LG GCE-8240B Bedienungsanleitung

LG GCE-8160B Bedienungsanleitung

Beliebte CD/CDR-Laufwerk Handbücher anderer Marken

Philips

Philips CDD3610 Bedienungsanleitung

QPS

QPS Que!Fire Bedienungsanleitung

Plextor

Plextor 12X-3 Leitfaden

Samsung

Samsung SN-324B Bedienungsanleitung

Teac

Teac CD-211E Bedienungsanleitung

SmartDisk

SmartDisk Firewire CD-R/W Bedienungsanleitung

Axis

Axis CD-ROM SERVER Bedienungsanleitung

Memorex

Memorex 32023234 - 52x32x52x External USB2.0 CD... Montageanleitung

Yamaha

Yamaha CD Recordable/Rewritable Drive CRW3200 Bedienungsanleitung

Sony

Sony CRX230AE Bedienungsanleitung

Sony

Sony CRX - 160E Bedienungsanleitung

Panasonic

Panasonic KX-LD742 Bedienungsanleitung

Pioneer

Pioneer BDR-S13U-X Bedienungsanleitung

Panasonic

Panasonic LK-MC606BP Bedienungsanleitung

Panasonic

Panasonic CF-VCW Series Bedienungsanleitung

Conner

Conner CFP2107 Series Bedienungsanleitung

Sony

Sony CRX-1611 Bedienungsanleitung

Plextor

Plextor 12-20C Leitfaden