LG LG-TM540 Bedienungsanleitung

LG-TM540

User Guide

CDMA/AMPS/PCS TRI-MODE PHONE

For more information about RF exposure, please visit the FCC website at www.fcc.gov

FCC RF EXPOSURE INFORMATION

In August 1996 the Federal Communications Commission (FCC) of the United States

with its action in Report and Order FCC 96-326 adopted an updated safety standard

for human exposure to radio frequency electromagnetic energy emitted by FCC

regulated transmitters. Those guidelines are consistent with the safety standard

previously set by both U.S. and international standards bodies. The design of this

phone complies with the FCC guidelines and these international standards.

Use only the supplied or an approved antenna. Unauthorized antennas,

modifications, or attachments could impair call quality, damage the phone, or result in

violation of FCC regulations.

Do not use the phone with a damaged antenna. If a damaged antenna comes into

contact with the skin, a minor burn may result. Please contact your local dealer for

replacement antenna.

Body-worn Operation

This device was tested for typical body-worn operations with the back of the phone

kept 1.5 cm. from the body. To maintain compliance with FCC RF exposure

requirements, use only belt-clips, holsters or similar accessories that maintain a 1.5

cm. separation distance between the user’s body and the back of the phone, including

the antenna, whether extended or retracted. The use of third-party belt-clips, holsters

and similar accessories should not contain metallic components in its assembly. The

use of accessories that do not satisfy these requirements may not comply with FCC

RF exposure requirements, and should be avoided.

WARNING! Read this information before using your phone

Contents

Introduction

Highlights

Important Information

Check Accessories

Before You Start

FCC RF EXPOSURE INFORMATION

Chapter 1. Getting Started

Cautions

Phone Overview

On screen Icons

Chapter 2. Basic Functions

Turning the Phone On and Off

Making a Call

Correcting Dialing Mistakes

Receiving Calls

Using Quick Mode

Call Waiting

Mute

Redialing Calls

Adjusting the Volume

Power Save Mode

Signal Strength

Emergency Dialing

Mini Display

Speed Dialing

Caller ID

Phone Book Features

Chapter 3. Menu Features

General Guidelines to MENU Access and Settings

Sound

Display

System

Features

Utility

Security

Voice Services

Browser Start

Chapter 4. Book Features

Call History

Phone Book

Function of Scheduler

General Guidelines to Scheduler Access and Settings

Scheduler Item Descriptions

Schedule

Wake Up

Viewing Your Telephone Number

Chapter 5. Message Features

Voice

Send Msg

New Text

Old Text

Erase All

Setting

Chapter 6. Functions used during a call

Mute

Memo

Recording

Key Tone

Voice Privacy

Chapter 7. Accessories

Chapter 1. Getting Started

Cautions

lUsing the phone in proximity to receiving equipment (i.e., TV or radio) may cause

interference.

lKeep your phone in a safe place when not in use.

lOnly use the batteries, antennas, and chargers provided by LG. Using the wrong

accessories could void your warranty.

lOnly authorized personnel should service the phone and its accessories. Faulty installation

or service may result in accidents and consequently invalidate the warranty.

lDo not hold the antenna while the phone is in use.

lDo not use the phone in designated “no cellular phone use” areas.

lDo not expose the phone to high temperature or humidity.

lAvoid getting your phone wet. If the phone gets wet, turn the power off immediately and

remove the battery pack. If the phone is mal-functional, return it to the dealer for service.

lAvoid shock or impact on the phone.

Phone Overview

Function Key Descriptions

Lamp The red light goes on when you use the power key to turn on the phone and when there are

incoming calls and messages.

LCD screen Displays messages & indicator icons.

END/PWR Used to turn power on/off. This key disconnects a call. Using this key, you can also exit out of

a menu back to the phone’s standby display without changing the setting.

SEND Allows user to place or answer calls.

Mouse Key This mouse key allows quick access to text and voice mail notification messages. calendar,

outgoing call log, phonebook Find name.

Cellcase Close the active cellcase to the terminate a call in progress.

Open the active cellcase to answer an incoming call.

Soft Keys

The current operation of a soft key is defined by the word at the bottom of the display.

Soft Keys 2 :

If you press this key once in a menu, you can go back one level and if you press and hold the

key in a menu, you can go back to the standby display.

Side Keys These keys enable you to adjust keybeep volume (in standby mode) and earpiece volume (in a

call status).

Scroll Keys These keys are used to scroll through the memory locations and menu items.

-In the standby status, set the manner mode by pressing the button. (for 2 seconds)

-In the standby status, set the lock function by pressing the button. (for 2 seconds)

Alphanumeric

Keypad These keys enable you to enter numbers and characters and choose menu items.

Clear Key

On screen Icons

The phone screen displays several onscreen icons and onscreen icons appears when the phone is

power on.

Icons Descriptions

Displays the strength of the signal received by the phone and current signal

strength is indicated as the number of bars displayed on the screen.

No service

The phone is not receiving a system signal.

In use

A call is in progress.

No icon indicates the phone is in standby mode.

Digital indicator

Digital service is available.

Analog indicator

Analog service is available

Indicates that a text message or voice mail has been received

Roaming

The phone is outside of its home service area.

Charge level

Indicates battery charge level.

Chapter 2. Basic Functions

Turning the Phone On and Off

Turning the Phone On

1. Install a charged battery pack or connect the phone to an external power source such as the

cigarette lighter adapter or car kit.

2. Press [END/PWR] for a few seconds until the red light on the top of the phone flashes.

lFully extend the antenna for the best performance.

<Note> Like any other radio device, avoid any unnecessary contact with the antenna while your

phone is on.

Turning the Phone Off

1. Press and hold until display screen will be turned off, and then release the key.

2. Protect the antenna by pushing it back into the phone, if extended.

Making a Call

When you make a call, follow these simple steps:

1. Make sure the phone is turned on.

lIf not, press [END/PWR].

2. Enter the phone number with area code, if needed.

3. Press [SEND].

lIf the phone is locked, enter the lock code.

l“Call Failed” indicates that the call di d not go through.

4. Press [END/PWR] to disconnect the call.

Correcting Dialing Mistakes

If you make mistakes in dialing a number, press [CLR] key once to erase the last entered digit or

hold down [CLR] for at least two second to delete all digits, or simply press soft key 2 [BACK] to

exit dialing state.

Receiving Calls

1. When the phone rings, open cellcase or If cellcase is open, press any key (except [END/PWR],

[5][6], [3v4]) to answer.

lIf you press the key [END/PWR], Side Keys ([5][6]) once when you receive a call, you

can hold the present call and ring sound or vibration stops. If you press the [END/PWR]

key, Side Keys ([5][6])twice, the present call is terminated.

2. Press [END/PWR] to disconnect the call.

In call waiting mode, the present call is on hold as you answer another incoming call.

This service is provided by your service provider.

When the call waiting function is activated, your phone will beep to let you know if you have an

incoming call. Your phone may also display the incoming caller’s identification.

Dialing a call from Phone Book

You can place a call from any memory location either by speed dialing or by pressing [SEND] while

looking up the memory location.

One-Touch Dialing : One-touch dialing is a convenient feature which enables you to dial

frequently used numbers in your personal phone book by pressing a key (for memory location 1

through 8).

lEntry 9 is designated to Emergency Call.

lFor locations 1 to 8, you can use one-touch dialing (if enabled, see “One-Touch” on page

37.) by pressing and holding down the key corresponding to the memory location.

lPress digit, then press [SEND].

Two-Touch Dialing (Speed Dialing) : This dialing feature enables you to dial numbers in your

phone book through two keys (for locations 10 to 99).

1) Press the first digit.

2) Press and hold the key of the second digit.

1) Press the first and second digits, then press [SEND].

Three-Touch Dialing (Speed Dialing) : This dialing feature enables you to dial numbers in your

phone book through three keys (for location 100 to 199).

1) Press the first and second digits.

2) Press and hold the key of the third digit.

Dialing from a Memory List

1) From a memory list, press the scroll keys to go to the memory location you want.

2) Press [SEND].

Dialing from a Memory Location.

On viewing and checking the memory location to call, press [SEND].

Chapter 3. Menu Features

General Guidelines to MENU Access and Settings

1. Press Soft Key [Menu]. The three menu items will appear on the display screen.

2. Press[v]to go through the list of menu features, or use the side keys.

3. Press the corresponding number to the menu item that you want to select. Then the sub-menu

list will appear on the screen.

4. Press the appropriate key to select the sub-menu you want to access.

5. Select preferred settings, using the [v]keys. Press Soft Key 2 [Back] to go one step backward

while accessing menu or selecting settings.

6. Press Soft Key 1 [Ok] to save the settings or Soft Key 2 [Back] to cancel without saving.

Sound ([Menu]+[1])

Ring Sound ([Menu]+[1]+ [1])

Select the ringer sound with [5] [6]or [v] key. The ring sound will notify that you have an

incoming call.

Ring Type ([Menu] +[1]+[2])

Select one out of four ring types (Ring, Vibrate, Vib+Ring and Lamp) with [5] [6]or [v] key.

Ring & Vibrate Volume ([Menu] +[1]+[3])

Adjust the volume of the ringer using the [5] [6]or [v] key.

Key Tone ([Menu] +[1]+[4] )

Set Key Tone length and touch tone playback speed.

lNormal : Sends out a tone for a fixed period of time only if you keep the key pressed.

lLong : Sends out a continuous tone for as long as you keep the key pressed.

Key Volume ([Menu] +[1]+[5] )

Adjust the key beep volume (the volume of sound on key pressing).

Ear Volume ([Menu] +[1]+[6] )

Adjust the earpiece volume during a call, by pressing the side keys.

Alerts ( [Menu]+[1]+[7] )

1. Fade ([Menu]+[7]+[1] )

Set an alert to inform you when you have lost a call or lose services.

2. Minute ([Menu]+[7]+[2] )

Alerts you 10 seconds before the end of every minute during a call.

3. Service ([Menu]+[7]+[3] )

If on, alerts you when service changes.

When you enter a service area, the phone displays “Entering Service Area” message.

When you leave a service area, the phone displays “Leaving Service Area” message.

4. Call Connect ([Menu]+[7]+[4] )

Alert tones notify the user of the time when the call is connected.

Display ([Menu]+[2] )

Backlight ([Menu]+ [2]+[1] )

Allows you to select how long or when the display screen and keypad are backlit. The backlight is

turned off 10 seconds after the last key is pushed. the backlight is turned off 30 seconds after the

last key is pushed. “On when Cellcase open” means that the backlight is always on while Cellcase

is open. “Always on” means that the backlight is on regardless of the Status of Cellcase. Choosing

“Always on”significantly decreases talk time. “Always off” means that the backlight is never on.

Contrast( [Menu] [2]+ [2] )

Banner ( [Menu]+ [2]+[3] )

Theme ( [Menu]+ [2]+[4] )

You can set up the screen displayed on the LCD screen in the standby mode.(Default, Star theme)

Language ([Menu]+ [2]+[5] )

Version ([Menu]+ [2]+[6] )

View the software and PRL version.

Features ([Menu]+[3])

Data ([Menu]+ [3] +[1])

In “Data/Fax” setting, data and fax can be transmitted. Wireless data communication services refer

to utilization of subscriber terminals for access to internet with personal computer or laptops at

8Kbps or at maximum of 13Kbps.

lData In : This setting enables the subscriber terminal to receive data calls.

lFax In : This setting enables the subscriber terminal to receive fax transmittals.

Auto Answer ([Menu]+ [3] +[2])

Select the ring type before the phone automatically answers a call. This feature is most commonly

used with the car kit.

off lafter 1 ring(or melody 5 seconds)

lafter 3 rings(or melody 10 seconds)

lMachine Enable

When you have incoming call, the phone automatically response with pre-recorded voice message

and record caller’s speech after 3 rings.

Auto Retry ([Menu]+ [3]+[3])

Set the length of time the phone waits before automatically redialing a number when the

attempted call fails.

loff / every 10 seconds / every 30 seconds / every 60 seconds

One-Touch ([Menu]+ [3]+[4])

Enable/Disable one-touch dialing.

Voice Privacy ([Menu]+ [3]+[5])

Set the voice privacy feature for CDMA calls as “Enhanced” or “Standard : CDMA offers inherent

voice privacy. Check with your service provider for availability of the enhanced voice privacy mode.

Audio AGC ([Menu]+ [3]+[6])

SIO Config ([Menu]+ [3]+[7])

If you want to use HSPD mode, you should set the baud rate as 230,400 bps in the menu 2 (Data

Baud menu).

1. Port Map (DATA DIAG OPTION)

U1 U2 -- : When using UART 1 and UART2 simultaneously

U1 -- HFK : When using UART 1 only for normal case

2. Data Baud (Data Baud Set)

AUTOBAUD : Default Data Baud Rate (ipr = 0)

9,600/19,200/38,400/57,600/115,200/230,400 : Optional Data Baud Rate

3. Diag Baud (Diag Baud Set)

38,400 : Default Diag Baud Rate

115,200 : Optional Diag Baud Rate

System ([Menu]+ [4])

System Select ([Menu]+ [4]+[1])

Choose setting to control which cellular company your phone uses. Leave this setting as default

unless you want to alter the system selection. (As instructed by your service provider.)

lHome is B (Automatic_B, Home only, Automatic_A) is displayed.

Set NAM ([Menu]+ [4]+[2])

Select the phone’ s NAM (Number Assignment Module) if the phone is registered with multiple

service provides.

Auto NAM ([Menu]+ [4]+[3])

Allows the phone to automatically switch to one of the programmed Telephone No. if it is operating

in the corresponding service provider area.

Force Call ([Menu]+ [4]+[4])

Make next call in analog mode. You have 30 seconds to place an analog call. This feature is

typically used for data applications.

TTY Mode ([Menu]+ [4]+[5])

To enable or disable TTY mode, select‘TTY Mode “Enable”/”Disable”‘using [5] [6]or [v] key.

If TTY mode is enabled, TTY Features is activated during call.

Security ([Menu]+[5])

Lock code is commonly last 4 digit of your phone. (You must enter the lock code after pressing

[Menu] ). If you need to modify the password, you may modify it using the “New Lock Code” of

Security.

Lock Mode ([Menu]+ [5]+[1])

Helps you to protect your phone from unauthorized use and once the phone is locked, the phone is

restricted from making calls until the lock code is entered.

However you can still receive phone calls and make emergency calls while your phone is locked.

“Never”means that the phone is never locked (Lock mode can be used). When locked, you can

only make emergency calls or receive incoming calls. “On power up” means that locked the phone

when the phone is turned on. “Always”means that the phone is always locked.

Restrict ([Menu]+ [5]+[2])

Set call restrictions to “Yes” or “No”. If set to “Yes”, you can only make calls to emergency numbers

and phone numbers in Phonebook Entry. You can still receive calls in restrict mode. Check with

your service provider.

Clear Call ([Menu]+ [5]+[3])

Allows you to delete all the telephone number saved in the “Call History”.

Clear Data ([Menu]+ [5]+[4])

Deletes all information saved in the memory location(001-199) (Entry 9 is designated to

Emergency Call). Be careful since any deleted information is not recoverable.

Emergency # ([Menu]+ [5]+[5])

To enter 3 emergency numbers ([Edit] →enter →number →[Save] →[v]→). You can call these

numbers and 911 even when the phone is locked or restricted.

New Lock Code ([Menu]+[5]+[6])

New Lock Code allows you to enter a new four-digit lock code number. For confirmation, it will ask

you to enter the new lock code twice. This is the same number as the pin code.

Voice Service ([Menu]+[6])

Allows you to make a call by simply saying the programmed word and when you are not available

to answer the phone, the caller can leave the message into voice mail and you can playback the

message later.

-Voice Dialing :

You can make a call by simply saying the programmed word.

-Voice Recording :

You can record conversation over the phone.

-Voice Memo :

When you are not available to answer the phone, the caller can leave the message into voice

mail.

-Auto Answering Machine :

When you are not available to answer the incoming call, you may set your phone as auto

Inhaltsverzeichnis

Beliebte Handy Handbücher anderer Marken

Zte

Zte BLADE A520 Bedienungsanleitung

Nokia

Nokia Lumia 620 Bedienungsanleitung

Blackbe;rry

Blackbe;rry KEYone Bedienungsanleitung

Bea-fon

Bea-fon X5 Premium Bedienungsanleitung

Blackbe;rry

Blackbe;rry 8707 Series Bedienungsanleitung

Blackbe;rry

Blackbe;rry Storm Betriebsanleitung

LifeWatch

LifeWatch V Bedienungsanleitung

Bea-fon

Bea-fon SILVER LINE SL860 Bedienungsanleitung

IKI Mobile

IKI Mobile KF4.5i Bedienungsanleitung

Hitech

Hitech HT-850 Bedienungsanleitung

Yezz

Yezz Fashion F10 Bedienungsanleitung

Point Mobile

Point Mobile PM60 Bedienungsanleitung

Blackbe;rry

Blackbe;rry Q10 Bedienungsanleitung

Blackbe;rry

Blackbe;rry Bold 9900 Bedienungsanleitung

Blackbe;rry

Blackbe;rry STORM 9500 - VERSION 5.0 Bedienungsanleitung

ISAFE MOBILE

ISAFE MOBILE IS655.2 Bedienungsanleitung

Blackbe;rry

Blackbe;rry CURVE 8300 - SMARTPHONE Bedienungsanleitung

Blackbe;rry

Blackbe;rry 8707 - VERSION 4.1 Bedienungsanleitung