LG Multi V SE Series Bedienungsanleitung

System

Heat Pump Indoor Unit

INSTALLATION MANUAL

MODELS : SE/S3 Series

Type : ART COOL Mirror

IMPORTANT

• Please read this installation manual completely

before installing the product.

• Installation work must be performed in accordance

with the national wiring standards by authorized

personnel only.

• Please retain this installation manual for future

reference after reading it thoroughly.

ENGLISH ITALIANO ESPAÑOL FRANÇAIS DEUTSCH

2Indoor Unit

Artcool Deluxe Type Indoor Unit Installation Manual

TABLE OF CONTENTS

❏ Installation guide map

❏Four type "A" screws & plastic

anchors

❏Connecting cable

❏Pipes: Gas side

Liquid side

(Refer to Product Data)

❏Insulation materials

❏Additional drain pipe

❏Two type "B" screws

❏Level gauge

❏Screw driver

❏Electric drill

❏Hole core drill

❏Horizontal meter

❏Flaring tool set

❏Specified torque wrenches

(different depending on model No.)

❏Spanner.......Half union

❏A glass of water

❏Screw driver

❏Hexagonal wrench

❏Gas-leak detector

❏Vacuum pump

❏Gauge manifold

❏Owner's manual

❏Thermometer

❏Holder Remote Controller

Installation Parts ....................3

Safety Precautions.................4

Installation

Selection of the best location

................................................7

Piping Method........................8

Drain Piping .........................12

Wiring Connection...............13

Installation of Remote

Controller..............................14

Installation Requirements Required Parts Required Tools

Installation Manual 3

Installation Parts

ENGLISH

Installation Plate Installation Plate

Type "A" screws and plastic anchorsType "A" screws and plastic anchors

Installation plate

Type 1

Type 1 Type 2

Type 2

Installation Parts

4Indoor Unit

Safety Precautions

To prevent injury to the user or other people and property damage, the following instructions must be followed.

■Be sure to read before installing the air conditioner.

■Be sure to observe the cautions specified here as they include important items related to safety.

■Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is classified by the

following indications.

■Meanings of symbols used in this manual are as shown below.

This symbol indicates the possibility of death or serious injury.

This symbol indicates the possibility of injury or damage to properties only.

Be sure not to do.

Be sure to follow the instruction.

■Installation

Do not use a defective or under-

rated circuit breaker. Use this

appliance on a dedicated circuit.

• There is risk of fire or electric shock.

For electrical work, contact the

dealer, seller, a qualified electri-

cian, or an Authorized Service

Center.

• Do not disassemble or repair the

product. There is risk of fire or elec-

tric shock.

Always ground the product.

• There is risk of fire or electric shock.

Install the panel and the cover

of control box securely.

• There is risk of fire or electric shock.

Always install a dedicated cir-

cuit and breaker.

• Improper wiring or installation may

cause fire or electric shock

Use the correctly rated breaker

or fuse.

• There is risk of fire or electric shock.

Installation Manual 5

Safety Precautions

ENGLISH

■Operation

Do not modify or extend the

power cable.

• There is risk of fire or electric shock.

Do not let the air conditioner

run for a long time when the

humidity is very high and a door

or a window is left open.

• Moisture may condense and wet or

damage furniture.

Be cautious when unpacking

and installing the product.

• Sharp edges could cause injury. Be

especially careful of the case edges

and the fins on the condenser and

evaporator.

For installation, always contact

the dealer or an Authorized

Service Center.

• There is risk of fire, electric shock,

explosion, or injury.

Do not install the product on a

defective installation stand.

• It may cause injury, accident, or

damage to the product.

Be sure the installation area

does not deteriorate with age.

• If the base collapses, the air condi-

tioner could fall with it, causing prop-

erty damage, product failure, and

personal injury.

Do not store or use flammable gas or combustibles near the product.

• There is risk of fire or failure of product.

Gasolin

6Indoor Unit

Safety Precautions

Always check for gas (refriger-

ant) leakage after installation or

repair of product.

• Low refrigerant levels may cause

failure of product.

Install the drain hose to ensure

that water is drained away prop-

erly.

• A bad connection may cause water

leakage.

Keep level even when installing

the product.

• To avoid vibration or water leakage.

Do not install the product where

the noise or hot air from the out-

door unit could damage the

neighborhoods.

• It may cause a problem for your

neighbors.

Use two or more people to lift

and transport the product.

• Avoid personal injury.

Do not install the product where

it will be exposed to sea wind

(salt spray) directly.

• It may cause corrosion on the product.

Corrosion, particularly on the con-

denser and evaporator fins, could

cause product malfunction or inefficient

operation.

90˚

■Installation

Installation Manual 7

Installation

ENGLISH

Read completely, then follow step by step.

Installation

Selection of the best location

CAUTION : In case that the unit is installed near the sea, the installation parts

may be corroded by salt. The installation parts (and the unit) should be taken

appropriate anti-corrosion measures.

• There should not be any heat source or steam

near the unit.

• There should not be any obstacles to prevent the

air circulation.

• A place where air circulation in the room will be

good.

• A place where drainage can be easily obtained.

• A place where noise prevention is taken into con-

sideration.

• Do not install the unit near the door way.

• Ensure the spaces indicated by arrows from the

wall, ceiling, fence, or other obstacles.

The mounting wall should be strong and solid

enough to protect it from the vibration.

Mount the installation plate on the wall with four

Type "A" screws.

(If mounting the unit on the concrete wall, consid-

er using anchor bolts.)

• Always mount the Installation plate horizontally

by aligning the marking-off line by means of the

thread and a level.

More than 10 cm

More than 50 cm

More than 2.3m

More than 50 cm

Chassis

Hook

Installation Plate

Type “A”

Type 2

(SE chassis)

Type 1

(S3 chassis) Installation Plate

Type 1

(S3 chassis) Type 2

(SE chassis)

Installation plate

Left rear piping Right rear piping

Ø70mm Ø70mm

110mm

65mm

85mm

Installation plate

Left rear piping Right rear piping

Ø70mm Ø70mm

155mm

78mm

306mm

The lower left and the right side of Installation Plate

8Indoor Unit

Installation

Piping Method

■Preparing the indoor unit's piping and drain hose for

installation through the wall.

■Remove the plastic tubing retainer(see illustration

below) and pull the tubing and drain hose away from

chassis.

■Replace the plastic tubing holder in the original position.

1. Route the indoor tubing and the drain hose in the

direction of rear left.

2. Insert the connecting cable into the indoor unit

from the outdoor unit through the piping hole.

■Do not connect the cable to the indoor unit.

■Make a small loop with the cable for easy connection

later.

3. Tape the tubing, drain hose and the connecting

cable. Be sure that the drain hose is located at the

lowest side of the bundle. Locating at the upper

side can cause drain pan to overflow inside the

unit.

: If the drain hose is routed inside the room,

insulate the hose with an insulation material* so that drip-

ping from "sweating"(condensation) will not damage furni-

ture or floors.

*Foamed polyethylene or equivalent is recommended.

4. Indoor unit installation

■Hook the indoor unit onto the upper portion of the

installation plate.(Engage the two hooks of the rear

top of the indoor unit with the upper edge of the

installation plate.) Ensure that the hooks are properly

seated on the installation plate by moving it left and

right.

Press the lower left and right sides of the unit against

the installation plate until the hooks engage into their

slots(clicking sound).

NOTICE

For right rear piping

Drain hose

Connecting

pipe

Connecting cable

Tape

Drain hose

Connecting

cable

•Drill the piping hole with a ø70mm hole core drill.

Drill the piping hole at either the right or the left

with the hole slightly slanted to the outdoor side.

Drill a Hole in the Wall

5-7mm

(3/16"~5/16")

Indoor WALL Outdoor

Installation Manual 9

Installation

ENGLISH

5. Connecting the pipings to the indoor unit and drain

hose to drain pipe.

■Align the center of the pipings and sufficiently tighten

the flare nut by hand.

■Tighten the flare nut with a wrench.

■Mount the clamp on the boss with a type "B"

screw.(optional)

■When extending the drain hose at the indoor

unit, install the drain pipe.

6. Wrap the insulation material around the connect-

ing portion.

■Overlap the connection pipe insulation material

and the indoor unit pipe insulation material. Bind

them together with vinyl tape so that there is no

gap.

■Wrap the area which accommodates the rear pip-

ing housing section with vinyl tape.

■Bundle the piping and drain hose together by

wrapping them with vinyl tape over the range with-

in which they fit into the rear piping housing sec-

tion.

1. Route the indoor tubing and the drain hose to the

required piping hole position.

2. Insert the piping, drain hose and the connecting

cable into the piping hole.

For left rear piping

Torque

wrench

Indoor

unit tubing

Spanner (fixed)

Connection

pipe

Flare nut

Vinyl tape(narrow)

Connection

pipe

Connecting cable

Vinyl tape

(wide) Wrap with vinyl tape

Indoor

unit pipe

Pipe

Wrap with vinyl tape

Drain hose

Pipe

Vinyl tape(wide)

Drain pipe

Connecting cable

Vinyl tape(narrow)

Adhesive

Drain pipe

Indoor unit

drain hose

Plastic bands Insulation material

GAS LIQUID

Ø12.7[5.5kg.m] Ø6.35[1.8kg.m]

Ø15.88[6.6kg.m] Ø9.52[4.2kg.m]

Pipe Size[Torque]

Drain hose

Clamp

Boss

Type "B" screw

Indoor unit tubing Flare nut Pipings

10 Indoor Unit

Installation

3. Insert the connecting cable into the indoor unit.

■Don't connect the cable to the indoor unit.

■Make a small loop with the cable for easy connec-

tion later.

4. Tape the drain hose and the connecting cable.

•Connecting cable

5. Indoor unit installation

■Hang the indoor unit from the hooks at the top of

the installation plate.

■Insert the spacer etc. between the indoor unit and

the installation plate and separate the bottom of

the indoor unit from the wall.

6. Connecting the pipings to the indoor unit and

the drain hose to drain pipe.

■Align the center of the pipings and sufficiently

tighten the flare nut by hand.

■Tighten the flare nut with a wrench.

■When extending the drain hose at the indoor unit,

install the drain pipe.

7. Wrap the insulation material around the connect-

ing portion.

■Overlap the connection pipe heat insulation and

the indoor unit pipe heat insulation material. Bind

them together with vinyl tape so that there is no

gap.

■Wrap the area which accommodates the rear pip-

ing housing section with vinyl tape.

Vinyl tape

Adhesive

Drain hose

Indoor unit drain hose

(narrow)

Plastic bands Insulation material

Vinyl tape

(narrow)

Connection

pipe

Connecting

cable

Indoor

unit piping

Pipe

Vinyl tape

(wide)

Wrap with vinyl tape

Indoor unit tubing Flare nut Pipings

Torque

wrench

Indoor

unit tubing

Spanner (fixed)

Connection

pipe

Flare nut

Installation plate

Spacer

Indoor unit

8cm

GAS LIQUID

Ø12.7[5.5kg.m] Ø6.35[1.8kg.m]

Ø15.88[6.6kg.m] Ø9.52[4.2kg.m]

Pipe Size[Torque]

Andere Handbücher für Multi V SE Series

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere LG Wärmepumpe Handbücher

LG Multi V CRUN Series Bedienungsanleitung

LG Therma V HM091MRS Bedienungsanleitung

LG ATNW18GTLP1 Produkthandbuch

LG THERMA V HN1639 Bedienungsanleitung

LG MULTI V ARUN072BTE4 Bedienungsanleitung

LG Therma V R32 Gen3 Handbuch

LG Multi V water mini Series Betriebsanleitung

LG Hydro Kit ARNH30GK1A4 Bedienungsanleitung

LG MULTI F Series Bedienungsanleitung

LG ARUV025GSD0 Produkthandbuch

LG ThermaV16 Bedienungsanleitung

LG THERMA V Series Bedienungsanleitung

LG THERMA V HN1639 Bedienungsanleitung

LG AH Series THERMA V Bedienungsanleitung

LG MULTI V WATER IV ARWN080LAS4 Produkthandbuch

LG THERMAV ZHBW056A1 Bedienungsanleitung

LG Multi V CRNN-SP Series Bedienungsanleitung

LG LH247HV Installations- und Betriebshandbuch

LG MULTI V WATER 5 ARW Series Installations- und Betriebshandbuch

LG THERMA V AHNW16606B0 Bedienungsanleitung

LG Multi V Water V ARWM072CAS5 Bedienungsanleitung

LG MULTI F Series Installations- und Betriebshandbuch

LG THERMA V Bedienungsanleitung

LG LC098HV4 Installations- und Betriebshandbuch

Beliebte Wärmepumpe Handbücher anderer Marken

MICROWELL

MICROWELL HP 1000 GREEN Bedienungsanleitung

Sanyo

Sanyo SAP120FCH Bedienungsanleitung

Daikin

Daikin EHYHBH05AA Bedienungsanleitung

Panasonic

Panasonic WH-SDF03E3E5 Leitfaden

Bryant

Bryant 544B Bedienungsanleitung

Airxcel

Airxcel 45000 Series Handbuch

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Bedienungsanleitung

Dimplex

Dimplex LI 16I-TUR Benutzerhandbuch

Carrier

Carrier WSHP Open v3 Kurzanleitung zur Einrichtung

TGM

TGM CTV14CN018A Bedienungsanleitung

Carrier

Carrier 38MGQ Series Bedienungsanleitung

Kokido

Kokido K2O K880BX/EU Fehlerbehebungshandbuch

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Kurzanleitung

Carrier

Carrier 48EZN Bedienungsanleitung

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Betriebsanleitung

Ariston

Ariston NIMBUS Bedienungsanleitung

Weishaupt

Weishaupt WWP L 7 Benutzerhandbuch

GE Zoneline AZ85H09EAC Bedienungsanleitung