LG THERMA V Bedienungsanleitung

INSTALLATION MANUAL

AIR-TO-WATER

HEAT PUMP

www.lg.com

Please read this installation manual completely before installing the

product. Installation work must be performed in accordance with the

national wiring standards by authorized personnel only. Please retain

this installation manual for future reference after reading it thoroughly.

Original instruction

MFL68681810

Rev.13_102720

ENGLISH ITALIANO ESPAÑOL FRANÇAIS DEUTSCH

ΕΛΛΗΝΙΚΆ

ČEŠTINA

NEDERLANDS

POLSKI

LIMBA ROMÂNĂ

PORTUGUÊS

MAGYAR

БЪЛГАРСКИ

SRPSKI

HRVATSKI

SLOVENŠČINA

TABLE OF CONTENTS

ENGLISH

6PREFACE

7SAFETY INSTRUCTIONS

15 INSTALLATION PART

18 GENERAL INFORMATION

18 Model Information

23 Model name and related information

24 Parts and Dimensions

37 Control Parts (For Split)

39 Control Parts (For Hydrosplit)

40 Control Panel

41 Typical Installation Example

46 Cycle Diagram (For R410A)

48 Cycle Diagram (For R32 Split)

49 Cycle Diagram (For Hydrosplit)

50 Water cycle (For R410A)

52 Water cycle (For R32 Split)

54 Water cycle (For Hydrosplit)

56 INSTALLATION OF OUTDOOR UNIT

56 Conditions where Outdoor Unit is Installed

56 Drill a Hole in the Wall (For Split)

57 Transporting the Unit

59 Installation at Seaside

60 Seasonal wind and cautions in winter

61 INSTALLATION OF INDOOR UNIT

61 Conditions where Indoor Unit is Installed

64 Flow area requirement : indoor unit(For R32 Split)

65 Ventilation requirements

68 Electrical Wiring

71 PIPING AND WIRING FOR OUTDOOR UNIT

71 Refrigerant Piping

72 Preparation for Piping

73 Connecting Pipe to Indoor Unit

73 Connecting Pipe to Outdoor Unit

76 Finalizing

77 Leakage test and Evacuation

81 Electrical Wiring

87 PIPING AND WIRING FOR INDOOR UNIT

87 Water Piping and Water Circuit Connection

91 Water pump Capacity

91 Pressure Drop

92 Performance curve

94 Water Quality

94 Frost protection

95 Water Volume and Expansion Vessel Pressure

TABLE OF CONTENTS

ENGLISH

96 ACCESSORIES INSTALLATION

98 Before Installation

98 Thermostat

106 3rd Party Boiler

107 3rd Party Controller

108 Meter Interface

109 Central Controller

110 DHW Tank

113 DHW Tank Kit

115 Solar Thermal Kit (For Split)

117 Solar Thermal System (For Hydrosplit)

118 Dry Contact

120 External Controller - Setting up programmable digital input operation

121 Remote Temperature Sensor

123 Solar pump

124 External pump

125 Wi-ﬁ Modem

126 Smart Grid (For Split)

127 Energy State (For Hydrosplit)

128 Digital Input for energy saving (ESS, Smart Grid)(For Hydrosplit)

129 2Way Valve

130 3Way Valve(A)

131 3Way Valve(B)

132 Final check

133 CONFIGURATION

133 DIP Switch Setting (For Split)

138 DIP Switch Setting (For Hydrosplit)

144 SERVICE SETTING

144 How to enter service setting

144 Service setting

145 Service contact

146 Model information

147 RMC version lnformation

148 Open source license

149 INSTALLER SETTING

149 How to enter installer setting

150 Installer setting (For Split)

152 3 Minutes Delay

153 Select Temperature Sensor

154 Dry Contact Mode

155 Central Control Address

156 Pump test run

157 Air cooling set temp.

158 Water cooling set temp.

159 Air heating set temp.

160 Water heating set temp.

161 DHW set temp.

162 Screed drying

164 Heater on temperature

166 Water supply off temp. during cooling

168 Tank disinfection setting 1, 2

TABLE OF CONTENTS

ENGLISH

169 Tank setting 1

170 Tank setting 2

172 Heater priority

173 DHW time setting

174 TH on/off Variable, heating air

175 TH on/off Variable, heating water

176 TH on/off Variable, cooling air

177 TH on/off Variable, cooling water

178 Heating temp. setting

179 Cooling temp. setting

180 Pump setting in heating

181 Pump setting in cooling

182 Forced operation

183 CN_CC

184 Pump frequency setting (RPM)

185 Pump Capacity

186 Smart Grid(SG)

187 Seasonal auto temp.

189 Modbus Address

190 CN_EXT

191 Anti-freezing Temperature

192 Add Zone

193 Use External Pump

194 3rd Party Boiler

195 Meter Interface

196 Pump Prerun/Overrun

197 Solar Thermal System

199 Current ﬂow rate

200 Data logging

201 Password Initialization

202 Power Supply Blockage (Smart Grid)

203 Overview settings

205 Installer setting (For Hydrosplit)

208 Select Temperature Sensor

209 Use Heating Tank Heater

210 Mixing Circuit

211 Use External Pump

211 RMC master/slave

212 LG Therma V Conﬁguration

213 Forced operation

214 Pump Prerun/Overrun

215 Water Flow Control

216 Password Reset

217 Screed drying

219 Heater on temperature

221 Air heating set temp.

222 Water heating set temp.

223 Hysteresis Room Air(Heating)

224 Hysteresis Heating Water

225 Heating temp. setting

226 Pump setting in heating

227 Air cooling set temp.

228 Water cooling set temp.

229 Water supply off temp. during cooling

231 Hysteresis Room Air(Cooling)

232 Hysteresis Cooling Water

TABLE OF CONTENTS

ENGLISH

233 Cooling temp. setting

234 Pump setting in cooling

235 Seasonal auto temp.

238 Heater priority

239 DHW set temp.

240 Tank disinfection setting 1, 2

241 Tank setting 1

242 Tank setting 2

244 DHW time setting

245 Solar Thermal System

247 Pump test run

248 Frost Protection Temp.

249 Dry Contact Mode

250 Central Control Address

251 CN_CC

252 Energy state

253 Thermostat control type

254 Pump operation time

255 IDU operation time

256 Modbus Address

257 Modbus gateway memory map

260 CN_EXT

261 3rd Party Boiler

262 Meter Interface

263 Current ﬂow rate

264 Data logging

265 COMMISSIONING

265 Check List before Starting Operation

266 Starting Operation

267 Starting Operation ﬂow chart

267 Airborne Noise Emission

267 Limiting concentration(For R410A)

268 Vacuum & Charge of Refrigerant

271 Troubleshooting

PREFACE

ENGLISH

PREFACE

This installation manual is to present information and guide about understanding, installing,

and checking .

Your careful reading before installation is highly appreciated to make no mistake and to prevent

potential risks. The manual is divided into ten chapters. These chapters are classified according to

installation procedure. See the table below to get summarized information.

REMARK : ALL CONTENTS OF THIS MANUAL ARE SUBJECT TO CHANGE WITHOUT NOTICE.

TO GET THE LATEST INFORMATION, PLEASE VISIT LG ELECTRONICS WEB SITE.

Chapters Contents

Chapter 1

• Warning and Caution concerned with safety.

• This chapter is directly related with human safety. We strongly recommend reading this

chapter carefully.

Chapter 2

• Items Inside product Box

• Before starting installation, please make it sure that all parts are found inside the product

box.

Chapter 3

• Fundamental knowledge about

• Model identification, accessories information, refrigerant and water cycle diagram, parts

and dimensions, electrical wiring diagrams, etc.

• This chapter is important to understand

Chapter 4

• Installation about the outdoor unit.

• Installation location, constraints on installation site, etc

Chapter 5

• Installation about the indoor unit.

• Installation location, constraints on installation site, etc

• Constrains when accessories are installed

Chapter 6

• How to perform piping (for refrigerant) and wiring at the outdoor unit.

• Refrigerant pipe connection between the indoor unit and the outdoor unit.

• Electrical wiring at the outdoor unit.

Chapter 7

• How to perform piping (for water) and wiring at the indoor unit.

• Water pipe connection between the indoor unit and pre-built under floor water loop pipe.

• Electrical wiring at the indoor unit.

• System set-up and configuration.

• As many control parameters of is adjustable by control panel, deep

understanding about this chapter is required to secure the operation flexibility of

• For more detailed information, please read the separate operation manual to use control

panel and adjust control parameters.

Chapter 8

• Information about supported accessories

• Specification, Constraints, and wiring are described.

• Before purchasing accessories, please find supported specification to buy proper one.

Chapter 9

• Test operation and check point while test running.

Chapter 10

• Check points before starting operation are explained.

• Troubleshooting, maintenance, and error code list are presented to correct problems.

SAFETY INSTRUCTIONS

ENGLISH

WARNING

Installation

• Do not use a defective or underrated circuit breaker. Use this

appliance on a dedicated circuit.

- There is risk of fire or electric shock.

• For electrical work, contact the dealer, seller, a qualified

electrician, or an Authorized Service Center.

- There is risk of fire or electric shock.

Read the precautions in this

manual carefully before

operating the unit.

This appliance is filled with

flammable refrigerant (R32)

This symbol indicates that

the Operation Manual should

be read carefully.

This symbol indicates that a

service personnel should be

handling this equipment with

reference to the Installation

Manual.

SAFETY INSTRUCTIONS

WARNING

This indicates that the failure to follow the instructions can

cause serious injury or death.

CAUTION

This indicates that the failure to follow the instructions can

cause the minor injury or damage to the product.

This symbol is displayed to indicate matters and

operations that can cause risk. Read the part with this

symbol carefully and follow the instructions in order to

avoid risk.

The following safety guidelines are intended to prevent

unforeseen risks or damage from unsafe or incorrect operation

of the appliance. The guidelines are separated into ‘WARNING’

and ‘CAUTION’ as described below.

SAFETY INSTRUCTIONS

ENGLISH

• Always ground the unit.

- There is risk of fire or electric shock.

• Install the panel and the cover of control box securely.

- There is risk of fire or electric shock.

• Always install a dedicated circuit and breaker.

- Improper wiring or installation may cause fire or electric

shock.

• Use the correctly rated breaker or fuse.

- There is risk of fire or electric.

• Do not modify or extend the power cable.

- There is risk of fire or electric shock.

• Do not install, remove, or reinstall the unit by yourself

(customer).

- There is risk of fire, electric shock, explosion, or injury

• For antifreeze, always contact the dealer or an authorized

service center.

- Almost the antifreeze is a toxic product.

• For installation, always contact the dealer or an authorized

Service Center.

- There is risk of fire, electric shock, explosion, or injury.

• Do not install the unit on a defective installation stand.

- It may cause injury, accident, or damage to the unit.

• Be sure the installation area does not deteriorate with age.

- If the base collapses, the unit could fall with it, causing

property damage, unit failure, and personal injury.

• Do not install the water pipe system as Open loop type.

- It may cause failure of unit.

• Use a vacuum pump or inert (nitrogen) gas when doing

leakage test or purging air. Do not compress air or oxygen and

do not use flammable gases.

- There is the risk of death, injury, fire or explosion.

• Make sure the connected condition of connector in product

after maintenance.

- Otherwise, it may cause product damage.

SAFETY INSTRUCTIONS

ENGLISH

• Do not touch leaked refrigerant directly.

- There is risk of frostbite.

• Copper in contact with refrigerants shall be oxygen-free or

deoxidized, for example Cu-DHP as specified in EN 12735-1

and EN 12735-2.

• Compliance with national gas regulations shall be observed.

(for R32)

• Refrigerant tubing shall be protected or enclosed to avoid

damage. (for R32)

• The installation of pipe-work shall be kept to a minimum. (for

R32)

• A brazed, welded, or mechanical connection shall be made

before opening the valves to permit refrigerant to flow

between the refrigerating system parts. A vacuum valve shall

be provided to evacuate the interconnecting pipe and/or any

uncharged refrigerating system part. (for R32)

• Any person who is involved with working on or breaking into a

refrigerant circuit should hold a current valid certificate from an

industry-accredited assessment authority, which authorises

their competence to handle refrigerants safely in accordance

with an industry recognised assessment specification. (for

R32)

• Do not use means to accelerate the defrosting process or to

clean, other than those recommended by the manufacturer.

(for R32)

• Do not pierce or burn. (for R32)

• Be aware that refrigerants may not contain an odour. (for R32)

• Dismantling the unit, treatment of the refrigerant oil and

eventual parts should be done in accordance with local and

national standards. (for R32)

• Flexible refrigerant connectors (such as connecting lines

between the indoor and outdoor unit) that may be displaced

during normal operations shall be protected against mechanical

damage. (for R32)

SAFETY INSTRUCTIONS

ENGLISH

• Pipe-work shall be protected from physical damage. (for R32)

• Mechanical connections (mechanical connectors or flared

joints) shall be accessible for maintenance purposes. (for R32)

Operation

• Take care to ensure that power cable could not be pulled out

or damaged during operation.

- There is risk of fire or electric shock.

• Do not place anything on the power cable.

- There is risk of fire or electric shock.

• Do not plug or unplug the power supply plug during operation.

- There is risk of fire or electric shock.

• Do not touch (operate) the unit with wet hands.

- There is risk of fire or electric shock.

• Do not place a heater or other appliances near the power

cable.

- There is risk of fire or electric shock.

• Do not allow water to run into electric parts.

- There is risk of fire, failure of the unit, or electric shock.

• Do not store or use flammable gas or combustibles near the

unit.

- There is risk of fire or failure of unit.

• Do not use the unit in a tightly closed space for a long time.

- It may cause damage to the unit.

• When flammable gas leaks, turn off the gas and open a

window for ventilation before turning the unit on.

- There is risk of explosion or fire.

• If strange sounds, or smell or smoke comes from unit, turn the

breaker off or disconnect the power supply cable.

- There is risk of electric shock or fire.

Andere Handbücher für THERMA V

Inhaltsverzeichnis

Andere LG Wärmepumpe Handbücher

LG PRHR Series Bedienungsanleitung

LG THERMA V Bedienungsanleitung

LG 5BPU0-02D Produkthandbuch

LG THERMA V HM093MR Bedienungsanleitung

LG Hydro Kit ARNH30GK1A4 Bedienungsanleitung

LG THERMA V HN1639 Bedienungsanleitung

LG THERMA V Series Bedienungsanleitung

LG ARUM080LTE5 Produkthandbuch

LG THERMA V HA031M E1 Bedienungsanleitung

LG THERMA V HN1639 Bedienungsanleitung

LG ARNU12GSER1 Bedienungsanleitung

LG MULTI V LRNN-BE Series Bedienungsanleitung

LG LD187HHV4 Installations- und Betriebshandbuch

LG CRNN096BJG0 Bedienungsanleitung

LG MULTI F Series Bedienungsanleitung

LG MULTI-V SE Series Bedienungsanleitung

LG ARNU07GSEL1 Bedienungsanleitung

LG Multi V III Solo ARUN LM3 Series Bedienungsanleitung

LG THERMA V Bedienungsanleitung

LG Therma V R32 Gen3 Handbuch

LG Multi V mini Installations- und Betriebshandbuch

LG THERMA V AHUW126A3 Bedienungsanleitung

LG Multi V SE Series Bedienungsanleitung

LG THERMA V HM141MR Bedienungsanleitung

Beliebte Wärmepumpe Handbücher anderer Marken

MICROWELL

MICROWELL HP 1000 GREEN Bedienungsanleitung

Sanyo

Sanyo SAP120FCH Bedienungsanleitung

Daikin

Daikin EHYHBH05AA Bedienungsanleitung

Panasonic

Panasonic WH-SDF03E3E5 Leitfaden

Bryant

Bryant 544B Bedienungsanleitung

Airxcel

Airxcel 45000 Series Handbuch

Mitsubishi Electric

Mitsubishi Electric PUZ-SWM60VAA Bedienungsanleitung

Dimplex

Dimplex LI 16I-TUR Benutzerhandbuch

Carrier

Carrier WSHP Open v3 Kurzanleitung zur Einrichtung

TGM

TGM CTV14CN018A Bedienungsanleitung

Carrier

Carrier 38MGQ Series Bedienungsanleitung

Kokido

Kokido K2O K880BX/EU Fehlerbehebungshandbuch

Viessmann

Viessmann VITOCAL 300-G PRO Type BW 2150 Kurzanleitung

Carrier

Carrier 48EZN Bedienungsanleitung

Viessmann

Viessmann KWT Vitocal 350-G Pro Series Betriebsanleitung

Ariston

Ariston NIMBUS Bedienungsanleitung

Weishaupt

Weishaupt WWP L 7 Benutzerhandbuch

GE Zoneline AZ85H09EAC Bedienungsanleitung