LG MODBUS-RTU Bedienungsanleitung

MODBUS-RTU

Option Board for

SV-iS5 Series

Read this manual carefully before using the MODBUS-RTU Option board

and follow the instructions exactly.

After reading this manual, keep it at handy for future reference.

LG Industrial Systems







Thank you for purchase of LG Modbus-RTU Option Board!

SAFETY PRECAUTIONS

Always follow safety precautions to prevent accidents and potential hazards from occurring.

Safety precautions are classified into “WARNING” and “CAUTION” in this manual.

WARNING

CAUTION

Throughout this manual we use the following two illustrations to make you aware of safety

considerations:

Identifies potential hazards.

Read the message and follow the instructions carefully.

Identifies shock hazards.

Particular attention should be directed because dangerous voltage may be present.

Keep this manual at handy for quick reference.

CAUTION





Do not touch the CMOS components unless the board is grounded.

ESD can cause break down of CMOS components.



Do not change the communication cable with the inverter power is turned on.

Otherwise, there is a danger of connecting error and damage to the board.





Make sure to precisely insert the connector of inverter and option board

Otherwise, there is a danger of connecting error and damage to the board.

Indicates a potentially hazardous situation which, if not avoided, can

result in serious injury or death.

Indicates a potentially hazardous situation which, if not avoided, can

result in minor to moderate injury, or serious damage to the product.





Check the parameter unit when setting the parameters.

Otherwise, there is a danger of connecting error and damage to the board.

modbus-rtu iS5 manual.doc 2

 INTRODUCTION

By using a MODBUS-RTU Option board, SV-iS5 inverter can be connected to a MODBUS-RTU network.

1.1.

When you use the MODBUS-RTU Option Card …

Inverter can be controlled and monitored by the sequence program of the PLC or other master module. The

card provides a terminal block for an RS-485 interface. Up to 32 drives or other Modbus slave devices may

be connected in a multi-drop fashion on the RS-485 Modbus network and may be monitored or controlled by

a single PLC or PC.

1.1.1 Interfacing type of RTU Reference:

- Allows the drive to communicate with any other computers.

- Allows connection of up to 31 drives with multi-drop link system.

- Ensure noise-resistant interface.

Users can use any kind of RS232-485 converters. However a converter that has built-in ‘automatic RTS

control’ is highly recommended. The specifications of converters depend on the manufacturers. Refer to the

converter manual for detailed converter specifications.

1.1.2 Before Installation

Before installation and operation, this manual should be read thoroughly. If not, it can cause personal injury

or damage other equipment.

 SPECIFICATION

2.1.

Performance specification

Items Specifications

Communication method RS485

Transmission form Bus method Multi-drop Link System

Applicable inverter IS5 series drive

Number of drives Maximum 31 drives connectable

Transmission distance Max. 1200m (Less than 700 m recommended)

modbus-rtu iS5 manual.doc

Converter RS232-485, Use PC with RS232 card embedded

2.2.

Hardware Specifications

Installation CN2 connector on the inverter control board

Power

Supply

Control B/D From inverter power supply

Comm. B/D From control board (insulated)

modbus-rtu iS5 manual.doc 2

2.3.

Communication Specification

Communication speed 1200 /2400/4800/9600/19200 bps Selectable

Control procedure Asynchronous communication system

Communication system Half duplex system

Character system Binary (8 bit)

Start/Stop bit 1 bit

Error check (CRC16) 2 byte

Parity check None

 PRODUCT DETAIL

3.1.

Layout and detail

Name Description

Connector CN2, Connector to inverter main PCB

Signal

connection

terminal

Communication

signal connection

terminal

P 485 signal - high

N 485 signal – low

G 485 Ground

S Shield

Short T1 and T2 to connect a

termination resistor

modbus-rtu iS5 manual.doc

Figure 1. Layout

3.2.

Status LED

CPU LED Indicates normal operation of the board when blinking once per second.

RXD LED Receiving 485 signal

TXD LED Responding to 485 signal

ERR LED

On and Off intermittently Wrong DATA received (Normal

operating)

Blinking with CPU LED at the same

time

DPRAM communication fault

Blinking with CPU LED in an

opposite way

Network Connection TimeOut <I/O-49>

elapsed

 INSTALLATION

1. Connect the option board to the inverter control board using each connector on the board (See the

Figure 1).

modbus-rtu iS5 manual.doc 4

2. Double check the board is firmly installed to the board and then apply the inverter power.

3. When power ON, CPU LED is blinking per second after all LEDs blink one after another.

4. If “CPU LED” is not blinking, turn off the inverter power swiftly (if not, inverter and the board may

get damaged.) and check for the proper installation of the board. If the problem persists, contact

LG distributor.

5. Check ModBus-RTU is displayed in <COM-01>.

6. Set the parameters as below when the above steps are all done.

Parameter code Display Setting Value

< COM-01 > Opt B/D MODBUS displayed automatically

< COM-02 > Opt mode Set the Command controlled via

communication

< I/O- 46 > Inv. number 1~31

(Verify the assigned number is not duplicated)

< I/O- 47 > Baud-rate 9600 bps (Factory default)

< I/O- 48 > Lost command (Note1) User setting

< I/O- 49> TimeOut (Note 1) 0.1 sec (Factory default)

Note 1) it is used for Emergency Stop when communication between inverter and master is not done

properly. It is activated when communication is not done even once for the set time. It means remote

controlling of inverter is not done. Set this value for safety

7. Turn off the inverter power for the connection of the Converter when step 6 is finished.

8. if the inverter is to be placed at the end of the network trunk line, install a jumper at JP1 on the

Modbus card to enable the termination resistor.

 TROUBLE SHOOTING

If communications cannot be established with the drive, there are four LEDs on the Modbus card to aid in

troubleshooting. The CPU LED should blink once per second to indicate that the modbus card is interfacing

with the inverter main PCB properly. The RXD LED should blink each time a properly formed Modbus

message is received that is addressed to the inverter. The RXD LED will not blink when messages are

received that are addressed to other inverters or devices. The TXD LED should blink each time the inverter

responds to a Modbus message. The ERR LED indicates either an invalid request was received or there is

a problem with the Modbus card itself. The ERR LED should never light.

modbus-rtu iS5 manual.doc

 CPU LED

State Indicates Corrective measures

Blinking Card is installed properly and working

normally

Off Card is not installed properly Verify that the card is installed

properly

Inverter is not operating normally Verify that the inverter has power

  RXD and TXD LEDs

State Indicates Corrective measures

Blinking Card is functioning normally and receiving

and sending messages

modbus-rtu iS5 manual.doc 6

Inhaltsverzeichnis

Andere LG Netzwerk-Hardware Handbücher

LG N2A2DD2 Bedienungsanleitung

LG N4B1 Bedienungsanleitung

LG S1T1 Bedienungsanleitung

LG Musicflow MR140 Technisches Datenblatt

LG ETPFBTRP01 Bedienungsanleitung

LG N2A2DD2 Bedienungsanleitung

LG N2R1D - NAS Server Bedienungsanleitung

LG N2A2DD2 Bedienungsanleitung

LG CodePlus OAT100R Bedienungsanleitung

LG N4B2 Bedienungsanleitung

LG N2R1DD1 - NAS Server Bedienungsanleitung

LG V-net ACS PWFMDB000 Bedienungsanleitung

LG N2B1 Bedienungsanleitung

LG BP50NB40 Bedienungsanleitung

LG N2B1DD1 - NAS Server Stücklistenhandbuch

LG N2R1DD2 - N2R1 NAS Server Bedienungsanleitung

LG LRN8240D Series Bedienungsanleitung

LG LRN8240D Series Technisches Datenblatt

LG N2A3 Bedienungsanleitung

LG N1A1DD1 Bedienungsanleitung

LG ETPFFRPP01 Bedienungsanleitung

LG LRN8640N Bedienungsanleitung

LG LRN8240D Series Technisches Datenblatt

Beliebte Netzwerk-Hardware Handbücher anderer Marken

Matrix Switch Corporation

Matrix Switch Corporation MSC-HD161DEL Bedienungsanleitung

B&B Electronics

B&B Electronics ZXT9-IO-222R2 Bedienungsanleitung

Yudor

Yudor YDS-16 Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-320L Bedienungsanleitung

Samsung

Samsung ES1642dc Gebrauchsanweisung

Honeywell Home

Honeywell Home LTEM-PV Montageanleitung

evertz

evertz 7700 Series Bedienungsanleitung

D-Link

D-Link ShareCenter DNS-343 Bedienungsanleitung

Asante

Asante AsanteBridge 1012 Bedienungsanleitung

FireBrick

FireBrick FB2700 Bedienungsanleitung

Audiovox Electronics

Audiovox Electronics ARWH2T Bedienungsanleitung

ADC

ADC DSX-1 Handbuch

NetComm

NetComm NF2 Bedienungsanleitung

Alcatel-Lucent

Alcatel-Lucent 5620 Bedienungsanleitung

Dell EMC

Dell EMC XC6420 Series Bedienungsanleitung

Lanner

Lanner NCA-1020A Bedienungsanleitung

Allied Telesis

Allied Telesis AT-TN121-A Bedienungsanleitung

Lanner

Lanner NCA-1525 Bedienungsanleitung