LG PQRCUCA0 Kurzanleitung

Simple Wired Remote Controller

IMPORTANT

• Please read this installation manual completely

before installing the product.

• Installation work must be performed in

accordance with the national wiring standards

by authorized personnel only.

• Please retain this installation manual for future

reference after reading it thoroughly.

Owner's & Installation Manual

Visit us at : http://www.lgservice.com

Models: PQRCUCA0

2Simple Wired Remote Controller

Simple Wired Remote Controller Owner’s & Installation Manual

TABLE OF CONTENTS

■Safety Precautions..............................................................3~4

■Part Description ..................................................................5~6

■Wired remote controller switch information .........................7

■Installation Method .................................................................8

■Necessary functions before using .................................9~11

• Trial Operation..........................................................................................9

• Setting the Central Control Address ....................................................10

• ESP Function ..........................................................................................11

■How to use the Mode Selection Button.........................12~18

• Cooling Operation ..................................................................................12

• Heating Operation ..................................................................................13

• Auto-Operation .......................................................................................14

• Dry(Dehumidification) Operation ..........................................................15

• Fan Operation .........................................................................................15

• Fan Speed Selection ..............................................................................16

• Indoor Temperature Display..................................................................17

• Auto Swing..............................................................................................17

• Child Lock ...............................................................................................18

• Different Mode Operation .....................................................................19

Note) Please, refer to indoor's manual for product's detail information of subfunction

Safety Precautions

Owner’s & Installation Manual 3

■Installation

Service Center

Original Parts

Safety Precautions

• The installation requires expert skills, and it should be installed by the service center or other shops specialized

in the installation and recognized by our company.

• For all the problems arising after installation by someone who has no relevant qualifications, LG will not provide

free service.

• The following safety cautions are provided to prevent unexpected dangers or losses.

: If the user does not follow the mandatory items, it may result in serious injury or death.

: If the user does not follow the mandatory items, it may cause personal injury or property

damage.

: Warning and Caution are to call the user’s attention to the possible danger. Read and follow

them carefully in order to prevent a safety accident.

: Warning and Caution are indicated in this guide and the product itself to help protect the users

from danger.

WARNING

CAUTION

WARNING

Entrust installation of the

product to the service center

because improper installation

may cause fire, an electric

shock, explosion, and physical

injury.

Use the original parts in

order to prevent fire, an

electric shock, explosion,

and product breakdown.

Keep combustible and/or

inflammable materials away

from the product in order to

prevent fire or product

breakdown.

Do not disassemble, repair, or

modify the product at your

discretion in order to prevent fire

or an electric shock.

Do not install the product in wet

and humid areas in order to

prevent product breakdown.

Do not expose the product to the

sun in order to prevent product

breakdown.

Safety Precautions

4Simple Wired Remote Controller

Do not modify or lengthen the

power cable at your discretion.

It may cause fire or an electric

shock.

Do not place a heating device

near the product. It may cause

fire.

Do not drop water on to the

product. It may cause an electric

shock or product breakdown.

Do not place something heavy on

the power cable. It may cause fire

or an electric shock.

Do not place a heavy thing on the

product. It may cause product

breakdown.

Iftheproductwassubmerged

under water, ask the service

center for instruction. It may

causefireoranelectricshock

unless you do that.

■In-use

Service Center

Make sure children or senor

citizens use the product under

proper observation in order to

prevent safety accident.

Do not subject the product to

shock. It will cause product

breakdown.

Do not pick the product with a

sharp tool. It may cause

product breakdown with the

damage to its parts.

Do not clean the product with strong cleanser such

as solvent. Use soft clothes in order to prevent fire

or product deformation.

Do not touch the product with a wet hand. Do not

pull the lead cable. It may cause product breakdown

or an electric shock.

CAUTION

Part Description

Owner’s & Installation Manual 5

PQRCUCA0

FAN

SPEED

MODE

Cooling Heating Auto Dry Fan

Defrost Preheat Out door

Slo

Med

Room Temp

Total on

Central Run

1. Wired Remote Controller

2. LCD Screen

3. Connecting Cable and Connector

Part Description

Accessory

Connecting Cable

(1EA)

Fixing Screw (2EA) User / Installation

Manual

Installation Paper

Part Description

6Simple Wired Remote Controller

Simple Wired Remote Controller

PQRCUCA0

FAN

SPEED

MODE

Cooling Heating Auto Dry Fan

Defrost Preheat Out door

Slo

Med

Room Temp

Total on

Central Run

Each function will be shown on the display panel for three second or so when the power is applied at first.

1. Operation Display Panel

2. On/Off Function

3. Fan Speed Button

4. Temperature Control Button

5. Mode Selection Check

Button

Wired remote controller switch information

Owner’s & Installation Manual 7

S/W GR

Group Control

Ceiling Height/Default E.S.P

Room Temp. Sensing

Select Product

S/W

S/W 2

123

S/W 1

Product selection switch

1. Cooling ONLY product

2. HEAT PUMP product

Indoor temperature sensor

selection switch

1. Use the temperature sensor on the remote

controller

2. Use the temperature sensor on the product.

3. Use the sensor with the lower temperature

between the remote

Ceiling height selection switch

1. Low ceiling

2. Standard ceiling

3. High ceiling

Group control switch

1. For individual control use

2. For group control use

* When changing the product selection switch and

group control switch, the power must be

reconnected to reflect the changes.

Wired remote controller switch information

8Simple Wired Remote Controller

Installation Method

CN-REMO

LO2K

J15

LO1K

LO1D C07D

C01K

J14

CN-DISP

CN-M CN-ZONEC

IC01A

The position of the fixing screws

Side of

remote Controller

Side of

Indoor Unit

Main

indoor unit

Red Yellow Brown

Main frame

Fixing the

remote controller

2cm

Put the installation paper on the place and determine the

position and height of the fixing screws of the wired remote

controller.

•Refer to the printed side of the installation paper.

Plug the connecting cable into the indoor unit.

•The product is being shipped with the cable

connected only to the remote controller.

Fix the connecting cable with the cable rack.

Remove the installation paper before installing

the remote controller so that it can fit at the right

place.

* Do not embed the remote controller into the wall. (It may cause the breakdown of the temperature

sensor.)

* If you want to install a number of remote controller at the same place in a vertical line, install them at

regular intervals of 2cm. (It may cause the breakdown of the temperature sensor.)

* Do not install the cable with a distance of 50 m or longer. (This can cause communication error.)

* When installing the cable, check whether the connector between the remote controller and the product is

installed properly. The connector will not be connected when installed in opposite sides.

❏Supply the power after connecting wired remote controller.

When you need to change wired remote controller, switch off the main power and change it.

If the wired remote controller is changed before switching off the main power, the option function of the indoor

unit can't be used. (option function like "slo" fan speed selection)

Installation Method

Owner’s & Installation Manual 9

Necessary function before using

Necessary functions before using

Out door

Room Temp

Total on

Central Run

Defrost Preheat

PQRCUCA0

FAN

SPEED

MODE

The trial operation is to check the installation status of the product. The temperature will not be controlled during

trial operation. Instead the product will operate in several modes such as cooling, strong wind, comp-on.

* This function might not be available for Multi Product like Multi V system.

If you want to set the trial operation mode, press the

mode button and the Fan speed button same time for

three seconds.

Then the product will begin the trial operation and the

display will be like as shown on left side picture.

If you want to cancel the trial operation mode, just

press the On/Off button.

The trail operation will be shut down automatically

after 18 minutes and system will go to the standby

mode.

Trial Operation

10 Simple Wired Remote Controller

Note : The remote controller displays 'HL' if central controller has locked the remote controller .

Necessary function before using

Out door

Room Temp

Total on

Central Run

Defrost Preheat

PQRCUCA0

FAN

SPEED

MODE

FAN

SPEED

MODE

Group No.

Indoor Unit No.

If you want to set the address on the display panel,

press both temperature control buttons (▲/▼)same

time for three seconds.

Press the temperature-increasing button to change the

group number. Press the temperature-decreasing

button to change the indoor unit number.

e.g. As shown on the left side panel, it displays 23.

Group No. : 2

Indoor Unit No. : 3

Set the address by pressing both temperature control

buttons again(▲/▼) at the same time for three

seconds.

•If you connect the indoor unit to the central controller, you should set the network

address of the indoor unit so that the central controller could recognize it.

•The center-control address is composed of the group number and the indoor-unit

number.

Setting the Central-Control Address

Please set the address while using the central controller.

You don't need to set address if you don't use central controller.

Inhaltsverzeichnis

Andere LG Fernbedienung Handbücher

Beliebte Fernbedienung Handbücher anderer Marken

Panasonic

Panasonic EUR7622KB0 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen Beo4 Bedienungsanleitung

Sunwave Tech.

Sunwave Tech. RemoteComm SRC-7000 Bedienungsanleitung

Multiplex

Multiplex PROFI TX 9 Bedienungsanleitung

One Remote

One Remote RMB4 Bedienungsanleitung

FUTABA

FUTABA 9ZAP - PART2 Bedienungsanleitung

HR Matic

HR Matic HR MULTI 3 Bedienungsanleitung

Yamaha

Yamaha ACC-GNRST-30-20 Bedienungsanleitung

EisSound

EisSound KBSOUND Bedienungsanleitung

Marantz

Marantz RC101 Bedienungsanleitung

Conrad

Conrad FS20 TC6 Bedienungsanleitung

Anritsu

Anritsu MP1777A Bedienungsanleitung

Niles

Niles WVC100 Fehlerbehebungshandbuch

RCA

RCA RCU1300 Bedienungsanleitung

Bang & Olufsen

Bang & Olufsen BEO6 Bedienungsanleitung

GE 94901 Bedienungsanleitung

Onbon

Onbon YQ1-75 Bedienungsanleitung

FUTABA

FUTABA R7108SB Montageanleitung