LG DFSWLWT0A Bedienungsanleitung
DFSWLWT0A
Instruction Manual
Mini-Split Wireless Wall Thermostat Kit
Manuel d’instructions
Kit de thermostat mural sans fil Mini-Split
Manual de instrucciones
Kit de termostato inalámbrico
parapared Mini-Split
Mini-Split Wireless Wall ThermostatKit
Your kit includes:
1Thermostat
1Battery Backplate
1Mini-Split Control Card
4Plastic gyproc screw anchors and 4 screws
4432Screws – 1” which anchor the thermostat
tothe backplate
MINI-SPLIT THERMOSTAT CONTROL PACKAGE
LG Electronics, Inc.
IMPORTANT – LG Mini-Split UNIT must be
unplugged before starting the installation.
Refer to Mini-Split Owner’s Manual
1 Remove Front Grille Cover by pulling out the bottom of the front
grille and then lift up.
2 Remove Option Cover of the Control Box, located on the right
side, by removing the screw at the top.
3 Power up the LG Mini-Split UNIT.
4 Wire the Minisplit Control Card as per the diagram.
Once you have wired the card, place the sensor aligned to
the cover. Remove the adhesive cover and firmly press the
plastic housing to the Mini-split unit.
Installation Diagram of LG Mini-Split Control Board
ADVANCED SETTINGS
The LG Mini-Split Wireless Wall Thermostat Kit is
designed to work seamlessly with the LG Mini-Split
Unit. In many installations multiple units will be
installed so to ensure proper installation and opera-
tion each Wireless Wall Thermostat in every room
must be merged within the proximity of the Mini-
Split Unit the same room. Follow these steps for
success every time!
STEP 1
On the bottom right of the thermostat touch and release the black
reset button.
• Touch target centre
• When you see the display indicate touch for advanced settings
–touch the screen immediately
•Nowyou are ready to setup
the thermostat.
INSTALLING THE THERMOSTAT
Locateyour Thermostat approximately 5 ft (1.5m) meters above the
floor. For best results ensure that the thermostat is away from direct
sunlight and on an interior wall.
Using the dimensions 3.2” wide 3.1” (81mm x 78mm) high or the
template included, locate where the thermostat will be placed and cut
out the space on the wall.
Insertthe battery backplate into the cut-out area ensuring the top is up
Mark the four inside holesfor drilling the 3/16” holes required for the
plastic screwanchors
Remove the battery backplate and drill four (4) 3/16” holes in these
locations.
Insert the plastic gyproc screw anchors and tighten them securely.
Mount the battery backplate using four (4) supplied screws
Insert two (2) D batteries into the recess. Important: Use only Alkaline
Size D batteries for normal life operation.
Align four (4) pins on the thermostat tothe battery backplate and
gently but firmly attach the two units together
Using four (4) 1” screws provided, place them in the four outside
holes and fasten tightly. Replace the top trim.
1 DAYLIGHT TIME : Choose Daylight Time On or Off dependent
on your Time Zone.
ADVANCED SETTINGS - WELCOME
ENERGY WATCH: Enter the HVAC system consumption
parameters (rounded off to kW) as well as your electrical
energy cost (¢/kW) and the ENERGY WATCH feature
will display a real time totals of electrical energy consumption
and cost. To review touch the ENERGY WATCH button on
the MENU SCREEN.
*EXAMPLE: Heat Pump 1kW/ton, 5-30kW,7-9¢/kW
ENERGY WATCH feature will run consecutively for 255 days.
If you do not enter your information what will appear on
the display is the total time the Compressor has been
operating.
FILTER: Enter the air filter "fan run time" information here.
The Filter Monitor featureusesthis information to inform you
when tochange or clean your air filter by displaying
CHANGE FILTER icon on the HOME SCREEN.
ADVANCED SETTINGS
These are the factory default settings
➜IMPORTANT:By inadvertently modifying system configuration
settings, you may seriously degrade HVAC system performance.
➜Choose system heating and cooling equipment – remember all
you need to do is toggle the appropriate button until the correct
setting appears.
1 Choose HEAT PUMP (Factory setting)
2 Choose FURNACE OFF (No Furnace)
3 CYCLE RATE : Set the Maximum compressor cycles per hour.
We recommend that the factory default be maintained for
optimal performance.
HIGH Speed Fan
Medium Speed Fan
LowSpeed Fan
MAX Speed Fan
THE LG Mini Split Thermostat can run the fan in 4 speeds to
ensure quality air circulation and comfort. By initializing the
fan between 1 and 4 degrees from your setpoint, and choosing
the fan speed you control comfort and maximize efficiency,
and reduce fan noise.
The LG Wireless Wall Thermostat Kit is designed to work seamlessly
with the LG Mini-Split Unit. In many installations multiple units will
be installed so toensure proper installation and operation each
Wireless Wall Thermostat in every room must be merged with the
Mini-Split Unit the same room.
1Press INIT Mini-Split on thermostat screen 5 seconds until
you see the message: PLEASE WAIT….
2Immediatelypress the black button located on the Mini-Split
Control Card
ADVANCED SETTINGS
3Within 1 minute a message will appear on the screen acknowledging
the communication links:
LINK SUCCEEDED LINK FAILED
Touch TEST Mini-Split You need to repeat
The fan will immediately come on the above steps
4You have now merged the thermostat with the Mini-Split Unit.
Momentarily touch the reset button on the bottom right
corner of the thermostat and when the message TOUCH FOR LG
THERMOSTAT appears, touch immediately. You have now
configured the thermostat and you can move to the room settings.
ADVANCED SETTINGS
Final Phase
USING THE THERMOSTAT
International Icons provide friendly and easily recognizable sym-
bols with word back-up to control all features.
Your Mini-Split thermostat can run in Program Mode or hold a fixed
temperature.
RUN PROGRAM : Your custom program settings will be initiated
–4events per day including the fan mode.
HOLD TEMPERATURE : Allows you to raise or lower the
temperature setpoint by touching the heat/cool
•to lower + to raise
THERMOSTAT MODE
Menu Hold Temp Dehumidify Run Program Cool Heat Fan
Menu Hold Temp Dehumidify Run Program Cool Heat Fan
•HEAT : Raise or lower the heat setpoint
•COOL : Raise or lower the cool setpoint
•DE-HUMIDIFY : Initializesthe fan to reduce humidity
•HOME : Returns you to the main screen
TEMPERATURE MODE
•FAN AUTO : The fan will run on only when there is
ademand for heating or cooling.
•FAN ON : The fan runs continuously
FAN MODE
Menu Hold Temp Dehumidify Run Program Cool Heat Fan Menu Hold Temp Dehumidify Run Program Cool Heat Fan
MENU PAGE
➜Toaccess the Menu Page, simply touch Menu from the
Control Page. Remember it is as easy as a touch of
the button.
• Set-up of your Mini-Split Thermostat is effortless with intuitive
menu driven programming - on our patented touchscreen.
• Enter DATE AND TIME SETTINGS : Program 7 days with 4
events per day to improve efficiency and reduce energy costs
•ENERGY WATCH : display kWh consumption as well as the
dollar cost of the HVAC System - configure this feature in
Advanced Settings
• Access the SET SCREEN menu
• View FILTER MONITOR
•Select the 12 or 24 hour clock display.
•Set the time of day by choosing hour and minute buttons.
•Setthe Month, Day and Year by choosing the buttons.
MENU PAGE - DATE AND TIME SETTINGS
Menu Hold Temp Dehumidify Run Program Cool Heat Fan Menu Hold Temp Dehumidify Run Program Cool Heat Fan
Inhaltsverzeichnis
Andere LG Thermostat Handbücher
Beliebte Thermostat Handbücher anderer Marken
EWELLY
EWELLY EW-181 Bedienungsanleitung
Prolon
Prolon T1100 Montageanleitung
Computherm
Computherm Q20 Bedienungsanleitung
Heatmiser
Heatmiser neoStat Bedienungsanleitung
Aube Technologies
Aube Technologies TH111GFCI-NP 240 VCA Bedienungsanleitung
Mars
Mars HEAT CONTROLLER IR Wireless Thermostat Bedienungsanleitung
