LG LSK279-8TZM Bedienungsanleitung
Dual Tuner DVR STB Users Manual (Draft Version)
( Model : LSK279-8TZM )
Author : DTV Research Lab D1 Group
November. 14, 2007
1/12
Front & Rear Panel Specification
[ Front Panel Layout ]
[ Rear Panel Layout ]
2/12
Cable In
Cable Out
(loop-through)
Ethernet
S-Video Composite
Component
SPDIF
(Optical)
HDMI
AC Accessory
Outlet
Audio (L/R)
USB
iEEE-1394
External
SATA
AC Inlet
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates
uses and can radiate radio frequency energy and, if not in-stalled and used in accordance
with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on, the user is encouraged to try to
correct the interference by one or more of the following measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the equipment and receiver.
—Connect the equipment into an outlet on a circuit different from that to which
the receiver is connected.
—Consult the dealer or an experienced radio/ TV technician for help.
FCC Rules
“Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.”
Remote Control Lay-out
Basic Function + Hot Key
Navigation Key
Number + Character Input Key
Picture in Picture
Layout
Remote Controller
Remote Control Lay-out
* Requirement : ALL Classes of NGSTB's shall be able to receive signal transmitted by Motorola DRC800
and Philips RC1445301 remote controls and correctly interpret the IR code transmitted.
* Remote Control IR Codes
REMOTE control Key /IR code Mapping shall conform to the following table:
Key Name IR code
00
11
22
33
44
55
66
77
88
99
POWER 0A
CHAN + 0B
CHAN - 0C
V
OL + 0D
V
OL - 0E
MUTE 0F
SELECT/OK 11
EXIT 12
LAST CHANNEL 13
INPUT/RF BYPASS 14
FAVORITE 15
A (Yellow Triangle) 17
MENU 19
V
OD 1A
PLAY 1B
STOP 1C
FAST FORWARD 1D
REWIND 1E
PAUSE 1F
PiP ON/OFF 22
PiP SWAP 23
B (Blue Square) 27
C (Red Circle) 28
D (Green Diamond) 29
GUIDE 30
RECORD 31
INFO 33
UP 34
DOWN 35
LEFT 36
RIGHT 37
REPLAY 3C
LIST (DIG ITAL RECO RDING S) 3D
SKIP FO RW ARD 3F
A
SPECT 40
FiOS TV 41
Options 42
Widgets 43
*/CC 44
Remote Controller
Feature Description Method
OpenCable
Compliant
HD STB
A standard Interface
between OpenCable HD
STB and CableCARD
Module that handles CAS.
Creation of a bidirectional
OpenCable HD STB that satisfies
digital cable broadcast standard
using Broadcom Cable Chip
(BCM7400)
M-CARD UDCP Verification
Digital Cable
Signal
Transmission/Re
ception
In-Band Channel:
Reception of 64/256 QAM
signal
Communication between
STB and Head-End:
Down channel : Legacy
OOB,
Up channel : MoCA
MR-DVR Connectivity between
Home Devices
Home
Networking
Over Coaxial
Cable
Inter-compatibility and
Contents sharing between
CE, PC and Mobile Devices
via wired/wireless
networking,
Receiving 64/256 Digital cable QAM
signal via Cable in the home
For bidirectional communication
between cable Head-End and STB,
Legacy OOB (down channel) and
MoCA (up channel) are used.
Creation of On-board MoCA Module in
order to utilize MoCA in the home
Cable Network.
Creation of DLNA/UPnP stack for the
intercommunication between Consumer
devices in the home.
Participation in Plug Fest, Certification
and DLNA Logo program.
AV streaming via MoCA Network with
DLNA/UPnP stack
Viewing of saved server Contents using
media Player
Connectivity of Home Network Devices
Contents Up/Download feature
Link Protection (DTCP-IP)
Mobile Device Connectivity support
(HID)
- MIU: Media Interoperability
- M-NCF: Network Connectivity
New function introduction
3/12
In-home Networking and MR-DVR Through MoCA
•Entropic’s “c.LINK”enables cable STB with integrated PVR
or cable modem to be a whole-house solution extending
–PVR & IPTV services to all TVs
–Ethernet directly to a PC
•No consumer adoption or education issues
–Consumer is not aware of the presence of any network.
No new wires, connections, or behavior
5/12
MPEG-2
Stream
Multiplexer
Combine
/Splitter
OOB
Modulator
MPEG
Stream
Spooler Digital
Modulator Up-
converter
Cable Head-end (Signal Lab)
PSIP
Server
(In-band)
AV Channel
PSIP Table
CableCARD
PC ECB
Ethernet c.Link
[64/256 QAM Channel]
♦For the A/V Channel Tuning test, the existing QAM signal set up at the AV Business Dept.
will be used.
♦Verify A/V output and channel change with basic channel tuning.
[OOB Channel]
♦Produce random signals from the OOB Modulator and verify Tuning status.
[MoCA Channel]
♦Verify MoCA Network communication with Ethernet connection between the PC and ECB.
[CableCARD]
♦Verify CableCARD Operation.
[Home Networking]
♦Verify connectivity between STBs (Server/Client).
♦Verify Media Interoperability and Network Connectivity.
LGE Native UI App
OOB SI Table
Broadcom STB API
LG STB API
Operational Concept
Home
Networking
¾QAM/IP STB Operational Concept
6/12
1. In-band tuner tuned A/V channel Navigation
1) Without a cable card, turn the power on.
After the system boots, it will tune to a
preset channel like the screen on the left.
(Note) The first channel is tuned using saved
Channel information from the clear QAM
signal that is currently broadcasted from
the research lab.
(note) The banner OSD is setup to display the
currently tuned channel number.
2) If the remote control or front panel’s CH UP
or CH DN key is pressed, the A/V will mute and
tune to the next channel.
At this time the currently tuned channel number
will be displayed on the banner OSD. The
channel banner will automatically disappear
after 3 seconds.
3) If the channel change is complete, the
banner OSD will disappear and A/V will output.
2. Basic Set-top Box Functionality Verification
using the menu
1) MAIN MENU
If the MENU key is pressed, the Menu OSD will
be displayed like the screen on the left.
(Note) Basic MENU Navigation can be
performed using the UP, DOWN, LEFT, RIGHT
and SELECT (OK) keys.
(Note) Menu items will increase for future
functionality tests.
2) SYSTEM INFO
If the SELECT (OK) key is pressed at the Info &
Test menu, the Info & Test drop down menu
will be displayed.
Like the picture on the left, the System Info
menu item will display the Set-top Box’s basic
information (Model Number, S/W Information,
H/W Information, etc).
3) TUNER INFO
Tuner Info will show signal strength information
for the set-top’s 2 tuners in the form of simple
bars.
4) HDD INFO
HDD Info will show the set-top internal SATA
HDD’s basic information.
Inhaltsverzeichnis
Andere LG Tuner Handbücher
