LG DU-42PY10X Bedienungsanleitung

PLASMA TV

SERVICE MANUAL

CAUTION

BEFORE SERVICING THE CHASSIS,

READ THE SAFETY PRECAUTIONS IN THIS MANUAL.

CHASSIS : AF-044P

MODEL : DU-42PY10X DU-42PY10XH

CANADA : http//biz.lgservice.com

USA : http//www.lgservice.com

: http//lgservice.com/techsup.html

TV/VIDEO

VOL CH

POWER

TV GUIDE

- 2 -

SAFETY PRECAUTIONS

Many electrical and mechanical parts in this chassis have special safety-related characteristics. These parts are identified by in

the Schematic Diagram and Replacement Parts List.

It is essential that these special safety parts should be replaced with the same components as recommended in this manual to

prevent X-RADIATION, Shock, Fire, or other Hazards.

Do not modify the original design without permission of manufacturer.

General Guidance

An lsolation Transformer should always be used during

the servicing of a receiver whose chassis is not isolated from

the AC power line. Use a transformer of adequate power rating

as this protects the technician from accidents resulting in

personal injury from electrical shocks.

It will also protect the receiver and it's components from being

damaged by accidental shorts of the circuitary that may be

inadvertently introduced during the service operation.

If any fuse (or Fusible Resistor) in this monitor is blown, replace

it with the same specified type.

When replacing a high wattage resistor (Oxide Metal Film

Resistor, over 1W), keep the resistor 10mm away from PCB.

Keep wires away from high voltage or high temperature parts.

Leakage Current Cold Check(Antenna Cold Check)

With the instrument AC plug removed from AC source,

connect an electrical jumper across the two AC plug prongs.

Place the AC switch in the on positioin, connect one lead of

ohm-meter to the AC plug prongs tied together and touch other

ohm-meter lead in turn to each exposed metallic parts such as

antenna terminals, phone jacks, etc.

If the exposed metallic part has a return path to the chassis, the

measured resistance should be between 1MΩ and 5.2MΩ.

When the exposed metal has no return path to the chassis the

reading must be infinite.

An other abnormality exists that must be corrected before the

receiver is returned to the customer.

Leakage Current Hot Check (See below Figure)

Plug the AC cord directly into the AC outlet.

Do not use a line Isolation Transformer during this check.

Connect 1.5K/10watt resistor in parallel with a 0.15uF capacitor

between a known good earth ground (Water Pipe, Conduit, etc.)

and the exposed metallic parts.

Measure the AC voltage across the resistor using AC

voltmeter with 1000 ohms/volt or more sensitivity.

Reverse plug the AC cord into the AC outlet and repeat AC

voltage measurements for each esposed metallic part. Any

voltage measured must not exceed 0.75 volt RMS which is

corresponds to 0.5mA.

In case any measurement is out of the limits sepcified, there is

possibility of shock hazard and the set must be checked and

repaired before it is returned to the customer.

Leakage Current Hot Check circuit

CANADA: LG Electronics Canada, Inc. 550 Matheson

Boulevard East Mississauga, Ontario L4Z 4G3

USA : LG Customer Interactive Center

P.O.Box 240007, 201 James Record Road Huntsville,

AL 35824

Digital TV Hotline 1-800-243-0000

1.5 Kohm/10W

To Instrument's

exposed

METALLIC PARTS

Good Earth Ground

such as WATER PIPE,

CONDUIT etc.

AC Volt-meter

IMPORTANT SAFETY NOTICE

0.15uF

- 3 -

DESCRIPTION OF CONTROLS...........................................4

ADJUSTMENT INSTRUCTIONS ..........................................7

PRINTED CIRCUIT BOARDS.............................................17

BLOCK DIAGRAM...............................................................23

EXPLODED VIEW...............................................................24

EXPLODED VIEW PARTS LIST.........................................25

REPLACEMENT PARTS LIST............................................26

SCHEMATIC DIAGRAM..........................................................

TABLE OF CONTENTS

- 4 -

TV/VIDEO

VOL CH

POWER

TV GUIDE

POWER

Controls

- This is a simplified representation of front panel.

Here shown may be somewhat different from your TV.

Front Panel Controls

TV/VIDEO

VOL

TV GUIDE

MENU Button

TV/VIDEO Button

POWER Button

VOLUME (FF,GG) Buttons

CHANNEL (EE, DD) Buttons

INDEX

Switches

LED Display

on or off.

TV GUIDE Button

Remote Control

Sensor

TTruSurround XTruSurround XT

Power Indicator

Illuminates orange in stand-

by mode, Illuminates green

when the TV is turned on.

(If power isn’t turn on in red,

contact your service center.)

DESCRIPTION OF CONTROLS

- 5 -

Connection Options

RS-VIDEOVIDEO

L / MONO

AUDIO

FRONT A/V INPUT

DVI

COMPONENT2

DIGITAL AUDIO(OPTICAL)

VIDEO INPUT

AUDIO INPUT

CABLE

HDMI /

DVI(VIDEO)

Cable

ANTENNA

AC INPUT

Back Connection Panel

Antenna Inputs

Connect antenna sig-

nals to the TV, either

directly or through

your cable box.

RGB/AUDIO

INPUT

Connect the moni-

tor output connec-

tor from a PC to

the appropriate

input port.

Digital Audio (DVI: Digital

Visual

Interface/Component2)

Input/

Digital Audio Output

Connect digital audio from

various types of equipment.

Note: In standby mode,

these ports will not work.

DVD/DTV Input

(Component 1-2)

Connect a component

video/audio device to

these jacks.

Monitor Output

Connect a second

TV or Monitor.

Remote Control Port

Connect your wired

remote control here.

S-Video Input

Connect S-Video out

from an S-VIDEO

device to the S-

VIDEO input.

IEEE1394

Connect

DVHS or

MicroMV to

IEEE1394

Connector.

CABLE Inputs

Connect cable

signals to the TV,

either directly or

through your

cable box.

RS-232C

INPUT (CON-

TROL/SER-

VICE) PORT

Connect to the

RS-232C port

on a PC.

CableCARD

Used for

CableCARD

received Cable

Service Provider.

G-LINK

Connect an

IR controller

to this jack.

HDMI/DVI(VIDEO)

Connect a

HDMI/DVI(Video)

signal to this jack.

S-VIDEO Input

A connection available to provide bet-

ter picture quality than the video input.

VIDEO Input

Connects the video signal from a

video device.

AUDIO Input

Use to connect to hear stereo sound

from an external device.

Power Cord Socket

This TV operates on an AC power. The voltage is indi-

cated on the Specifications page. Never attempt to oper-

ate the TV on DC power.

Audio/Video Input

Connect audio/video

output from an exter-

nal device to these

jacks.

DESCRIPTION OF CONTROLS

- 6 -

-When using the remote control, aim it at the remote control sensor on the TV.

SKIP

LIGHT

TV/VIDEO

MODE

COMP/RGB/HDMI

MUTE SURF

VOL CH

PGUP

PGDN

INFO

SAP

RATIO

TV GUIDE

TIMER

EXIT

PLAY

PAUSE STOP

RECORD

PIP PIPCH- PIPCH+ PIPINPUT

ENTER

SIGNAL SWAP

REW FF

POWER

1394

FLASHBK

VIDEO SOUND

ADJUST

DAY +

DAY -

FREEZE ZOOM

LIGHT

Illuminates the remote control buttons.

TV/VIDEO

Selects: DTV, Analog, Video, Front Video,

Component 1-2, RGB-DTV (or RGB-PC),

HDMI/DVI input sources.

COMP/RGB/HDMI

Selects: Component 1-2, RGB-DTV (or RGB-

PC), HDMI/DVI input sources.

NUMBER buttons

DASH

Used to enter a program number for multiple

program channels such as 2-1,2-2,etc.

MUTE

Switches the sound on or off.

VCR/DVD BUTTONS

Control some video cassette recorders or

DVD player ("RECORD" button is not avail-

able for DVD player).

RATIO

Changes the aspect ratio.

MODE

Selects the remote operating mode: TV,

VCR, DVD, CABLE, HDSTB or AUDIO.

Select other operating modes, for the

remote to operate external devices.

POWER

Turns your TV or any other programmed

equipment on or off, depending on mode.

1394

SURF

Use to scroll the Surf channel.

Select a closed caption:

Off, CC1~4, Text1~4.

FLASHBK

Tunes to the last channel viewed.

THUMBSTICK (Up/Down/Left/Right/ENTER)

Allows you to navigate the on-screen menus

and adjust the system settings to your pref-

erence.

CHANNEL UP/DOWN

Selects available channels found with EZ

scan.

PAGE UP/PAGE DOWN

Moves from one full set of screen infor-

mation to the next one.

EXIT

Clears all on-screen displays and returns to

TV viewing from any menu.

TIMER

Lets you select the amount of time before

your TV turns itself off automatically.

VOLUME UP/DOWN

Increases/decreases the sound level.

SAP

Selects MTS sound: Mono, Stereo, and SAP

in Analog mode. Change the audio language

in DTV mode.

Brings up the main menu to the screen.

INFO

When you watch the TV, displays information

on top of the screen. Not available in

Component 1-2, RGB and HDMI/DVI mode.

TV GUIDE

Brings up the TV Guide On Screen system to

the screen.

PIP

Switches between PIP, POP (Picture-out-of-

Picture) and Twin picture modes.

PIPCH-/PIPCH+

Changes to next higher/lower PIP channel.

PIP INPUT

Selects the input source for the sub picture.

SWAP

Exchanges the main/sub images in

PIP/Twin picture mode.

VIDEO

Adjusts the factory preset picture

according to the room.

ADJUST

Adjusts screen position, clock, and

phase in PC mode.

SOUND

Selects the sound appropriate

for the program's character.

SIGNAL

Displays the digital signal strength.

Remote Control Key Functions

FREEZE

Freezes the currently-viewed picture. Main pic-

ture is frozen in PIP/Twin picture mode.

ZOOM

Enlarges the main picture size.

DAY+/DAY-

Moves forward of backwards in 24 hour

increments in the Listings Grid.

DESCRIPTION OF CONTROLS

- 7 -

1. Application Object

These instructions are applied to all of the PDP TV, AF-044P.

2. Notes

(1) Because this is not a hot chassis, it is not necessary to use

an isolation transformer. However, the use of isolation

transformer will help protect test equipment.

(2) Adjustments must be done in the correct order.

(3) The adjustments must be performed in the circumstance of

25±5°C of temperature and 65±10% of relative humidity if

there is no specific designation.

(4) The input voltage of the receiver be must kept 110V, 60Hz

when adjusting.

(5) The receiver must be operational for about 15 minutes

prior to the adjustments.

1) After receiving 100% white pattern, the receiver must be

operated prior to adjustment. (Or 9. White Pattern

condition in EZ - Adjust)

2) Enter into White Pattern

- Enter the Ez - Adjust by pressing ADJ Key on Service

Remote Control (S R/C).

- Select the 9. White Pattern using CH +/- Key and

press the Enter(Y) Key.

Display the 100% Full White Pattern.

[Set is activated HEAT-RUN without signal generator in

this mode.

If you turn on a still screen more than 20 minutes (Especially

Digital pattern(13 CH), Cross Hatch Pattern), an afterimage

may occur in the black level part of the screen.

3. EPLD Download

(1) Test Equipment: PC, Jig for download

(2) Connect the power of VSC B/D.

(3) Execute download program(iMPACK) of PC.

(4) After executing the hot key on the Programmer, click icon

(5) End after confirming

4. Gemstar VBI Micom Download

4-1. Preparation for Adjustment

(1) As shown below, connect the MPLAB ICD2 equipment, PC

and Digital Connector.

(2) Turn on the MPLAB ICD2 POWER Supply.

(3) After turn on the PC and MONITOR, select the ‘MPLAB

IDE’ from the screen.

4-2. Adjustment Sequence

(1) When the program is executed, select the MPLAB ICD2

from Programmer -> Select Programmer .

(2) Select "Configure -> Select Device".

(3) When the "Select Device" window appears, select the

PIC18F1220 from "Device" and press OK.

ADJUSTMENT INSTRUCTIONS

PC VSC

B/D

<Fig 1> Connection Diagram of EPLD Download

+13V

Connect the MPLAB ICD2 and connector of Digital Board

Connect the RS-232 or USB Cable

GND

Data

- 8 -

ADJUSTMENT INSTRUCTIONS

(4) Select "Programmer -> Connect".

When connected with the Micom, the display message on

the Output window appears as below.

(5) Select "File -> Import", select the Work HEX file and open.

(6) Select "Programmer -> Program".

(7) Download is executed and about 5 seconds later, the

"Programming succeeded" message is displayed on the

Output window and the Download process is ended.

(8) The execution of process (6) is convenient when using the

short-cut icon.

5. Gemstar IR Micom Download

5-1. Preparation for Adjustment

(1) As shown below, connect the MPLAB ICD2 equipment, PC

and Digital Connector.

(2) Turn on the MPLAB ICD2 POWER Supply.

(3) After turn on the PC and MONITOR, select the ‘MPLAB

IDE’ from the screen.

5-2. Adjustment Sequence

(1) When the program is executed, select the MPLAB ICD2

from "Programmer -> Select Programmer" .

(2) Select "Configure -> Select Device".

+13V

+5V

GND

Data

Clock

Connect the MPLAB ICD2 and connector of Digital Board

Connect the RS-232 or USB Cable

Connecting to MPLAB ICD 2

...Connected

Setting Vdd source to MPLAB ICD 2

Target Device PIC18F1220 found, revision = 0x4

...Reading ICD Product ID

Running ICD Self Test

...Passed

MPLAB ICD 2 Ready

- 9 -

ADJUSTMENT INSTRUCTIONS

(3) When the "Select Device" window appears, select the

PIC18F242 from "Device" and press OK.

(4) Select "Programmer -> Connect".

When connect with the Micom, the display message on the

Output window appears as below.

(5) Select "File -> Import", select the Work HEX file and open.

(6) Select "Programmer -> Program".

(7) Download is executed and about 3 seconds later, the

"Programming succeeded" message is displayed on the

Output window and the Download process is ended.

(8) The execution of process (6) is convenient when using the

short-cut icon.

6. POD Certificate Download &

IEEE1394(DTCP) Download

6-1. Preparation for Adjustment

(1) Connect the MEMORY JIG and PC.

(2) Turn on the JIG MAIN POWER SWITCH.

(3) After turn on the PC and MONITOR, execute the

‘Certificate Downloader v1.4’ from the screen.

6-2. Adjustment Sequence

(1) After open the ‘Certificate Downloader v1.4’, enter

Connection set and set the as same below.

The port settings are determined by each PC's setup.

Connecting to MPLAB ICD 2

...Connected

Setting Vdd source to MPLAB ICD 2

Target Device PIC18F242 found, revision = 0x7

...Reading ICD Product ID

Running ICD Self Test

...Passed

MPLAB ICD 2 Ready

- 10 -

ADJUSTMENT INSTRUCTIONS

(2) Select ‘Connection’ and SET connected to RS-232C.

(3) After clicking "Enter", confirm that "Enter Password:"

appears.

(4) Click the "OpenFile - Download" button from CP Data

Download, ‘select the Private Key’ appears and click

ENTER.

(5) After clicking ENTER, the ‘opens Private key' window

appears and select the Private key applied to the SET.

The Private Key file name is on the Label of the Digital

Board.

(6) When the Dialog window appears, click OK and the write

work will begin.

(7) When completed, click ‘CP Data Download: OK’

[When ‘CP Data Download: OK’ does not appear, certificate

has not Download correctly.

SET is rebooted and certificate Download work must be

repeated.

(8) Now, you may begin IEEE1394 (DTCP) Download work.

Select the “DTCP.dat” file by pressing the ‘DTCP File

Open’ button.

Andere Handbücher für DU-42PY10X

Dieses Handbuch passt für folgende Modelle

Inhaltsverzeichnis

Andere LG Fernseher Handbücher

LG 50PC1DR - - 50" Plasma TV Bedienungsanleitung

LG RE-28CB80RX Bedienungsanleitung

LG 55SK9000PUA Kurzanleitung

LG LCD Colour Television Bedienungsanleitung

LG 55LA620V Bedienungsanleitung

LG LG24V55 Produktinformationsblatt

LG LCD Colour Television Bedienungsanleitung

LG 47LS4600 Montageanleitung

LG 84LM9600 Bedienungsanleitung

LG LB55 Bedienungsanleitung

LG 32LG35 Series Bedienungsanleitung

LG 50PC1DR - - 50" Plasma TV Bedienungsanleitung

LG HECTO Bedienungsanleitung

LG DR385 Bedienungsanleitung

LG 43UK6500 Bedienungsanleitung

LG 55EW960H Bedienungsanleitung

LG 21FU6PL Bedienungsanleitung

LG RE-29FA34RB Bedienungsanleitung

LG UK63 Series Bedienungsanleitung

LG GoldStar CB-28C20X Bedienungsanleitung

LG 47LH90 Series Bedienungsanleitung

LG RT-32FZ30RB Bedienungsanleitung

LG 29FC2RNX/RNB Bedienungsanleitung

LG MC-049A Bedienungsanleitung

Beliebte Fernseher Handbücher anderer Marken

Philips

Philips Colour Television Bedienungsanleitung

Toshiba

Toshiba 27A10 Bedienungsanleitung

Philips

Philips 42PF9630A/37 Bedienungsanleitung

Hitachi

Hitachi 32FX48B Bedienungsanleitung

DAEWOO ELECTRONICS

DAEWOO ELECTRONICS DTQ-14V1FC Bedienungsanleitung

Changhong Electric

Changhong Electric uhd55b6000is Bedienungsanleitung

Philips

Philips Matchline 21CE7551 Bedienungsanleitung

Panasonic

Panasonic Genus TX-G10 Bedienungsanleitung

Toshiba

Toshiba 19A20 Bedienungsanleitung

Philips

Philips 25PT4523-16 Bedienungsanleitung

Sony

Sony XBR-100Z9D Bedienungsanleitung

Philips

Philips PR0930X3 Bedienungsanleitung

Philips

Philips Brilliance 231P4QPY Bedienungsanleitung

Samsung

Samsung 55S9 B Series Bedienungsanleitung

Philips

Philips 32HF9385D Fehlerbehebungshandbuch

Sharp

Sharp LC-40FI5012E Bedienungsanleitung

Loewe

Loewe Table Stand Reference 55 Bedienungsanleitung

Philips

Philips 32PFH5300 Bedienungsanleitung